- Home
- JCBP35DP1BB
- Instructions
JCBP35DP1BB General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Incorrect Burner Bowls
0 of 2 people
found this instruction helpful.
-
Valerie from Corvallis, OR
- Really Easy
- Less than 15 mins
For 12 years I've been suffering with the incorrect burner bowls...I love to cook and it's really irritating when your bowls don't fit correctly. Now, I am amazed at how my burners fit! Thank you! What a Blessing!
Other Parts Used:
Was this helpful?
Thank you for voting!
Light burnt out.
2 of 8 people
found this instruction helpful.
-
Roscoe G from ROCHESTER, NY
- Very Easy
- Less than 15 mins
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this helpful?
Thank you for voting!
Bad control board
-
Daryl from Savannah, TN
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
Removed top back plate of oven. unpluged all of the wiring plugs on the control board. Removed two screws on the control board. Removed face plate from old control board and put it on the new control board. Atteched new board with the two screws. Connected all of the plugs to new board ( all plugs are color coded to board). Re-installed o
... Read more
ven back plate. Pluged oven in. Works great.
Read less
Was this helpful?
Thank you for voting!
Plastic glide broke
-
Mary Ann from Granby, CT
- Really Easy
- Less than 15 mins
-
Screw drivers
The person I spoke to knew exactly what I was trying to describe. The part arrived in 2 days. 5 minutes later the drawer was back in place. I was glad I save the screw as the part did not come with one.
Was this helpful?
Thank you for voting!
The 8" burner switch heated burner to high Temp
-
Randy from Ellenboro, NC
- Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
Went online looked up model no and found Part No. and ordered it couple of days It came in mail Cut power to oven took knob off two screws back panel. wired new switch like the old one replced thwe switch and two screws and panel connected the power tried new switch it worked great.
Was this helpful?
Thank you for voting!
Mother board was blown
-
Kenneth from Bradenton, FL
- Easy
- 15 - 30 mins
Purchased the board installed it and saved about 130 dollars.
Was this helpful?
Thank you for voting!
Bottom Heating Element not heating up.
-
Wallace from Demorest,, GA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I miss diagnosed the situation at first. When the top element only heated up I thought the control was the problem. Wrong. Apparently both elements heat up during initial start up. It turned out that the bottom element was not working so it needed to be replaced rather then the control. Now both are replaced and the oven is now back
... Read more
to original status. Entire repair cost about $80. I saved over $100 by attempting this myself. Easy fix. Obviously I am not a pro. My local hardware store had a generic heating element that worked just fine and only cost $22. Two screws to repair after removing the back panel. Remember to pull the plug before you begin and after the repair put all panels back on before plugging back in. Pizza anyone?
Read less
Was this helpful?
Thank you for voting!
Burner switch shorted out
-
Robert from Blairsville, GA
- Really Easy
- 15 - 30 mins
-
Screw drivers
This burner is on a Monarch wood and electric range. The 8in burner shorted out and fried the switch. I had to remove the cover over the switch's. I marked each lead with paper and stapled the paper to the leads. When the switch came in I just had to reattach the leads.
Was this helpful?
Thank you for voting!
Burner went to high heat at any setting
-
Robert W from Whitehall, PA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Thanks to Partselect's instructions the repair went very easy. When I was done and the wife finished cleaning the sides of the stove and the floor behind it, I was surprised after I plugged the stove back in and noticed the clock was only 18 minutes off! Awesome company to deal with, Thanks!
Was this helpful?
Thank you for voting!
Replacment of burner control switches
-
Judith from Keezletown, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
I watched your video on the subject and followed it exactly. It explained everything I needed to know. The hardest part was CLEANING under the stove once I pulled it out from the wall!
Was this helpful?
Thank you for voting!
Burner was always on high when on.
-
David from Jericho, VT
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Disconnected the power. Removed hex head screws from top and lower rear panel. I think there were 8 all together. Pull the knob of the burner control, removed two screws that held the switch in place. Moved the wires one at a time to the new switch, re-assembled. Burner worked properly. Very easy to find the right part from this web
... Read more
-site, and the instructions from others like this were helpful. Easy fix!
Read less
Was this helpful?
Thank you for voting!
Burner light would not shut off
-
Curt from Maple Grove, MN
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Checked each burner switch by disconnecting the light indicator wire. Located the switch, replaced the switch and the indicator light operated as it should.
Was this helpful?
Thank you for voting!
The burner combusted burning the the burner switch
-
Felipe from Donna, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
Disconnected the appliacnce from the power source. Using screwdriver, removed the back panel and disconnected every wire that are connected to the switch. Pulled out the front nob and removed the switch. Then install the new switch by screwing it back in. Place all wires back and back panel. Connect and finish.
Was this helpful?
Thank you for voting!
clock, over control, oven light , timer did not work
-
Robert from Austin, AR
- Really Easy
- Less than 15 mins
-
Nutdriver
remove rear panel cover, removered four screws that held control panel, disconnected colored wires, removed circuit control board, reinstall new board and connected color coded wire to the correct spot on the board, plugged in 220 volt cord, switch on circuit breaker, everything worked normal again
Was this helpful?
Thank you for voting!
Orange light "Hot Stovetop" lense broke off.
-
John from Woodbridge, VA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Parts arrived in record time and the right parts. The detailed diagram was so helpful in finding exactly the part I needed to order. Was so easy my girlfriend with no mechanical or electrical experience completely helped me through the entire project. She secured the electrical breaker to the range, and I had the top back to the oven r
... Read more
emoved. I showed her how the little white box simply slides off the lens cover, then replaced the new one in the holes and slide it back on. Secured the back and she turned on the breaker back on...and all lights work. Thanks for making this project easy, simple and quick.
Read less
Was this helpful?
Thank you for voting!