EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JCBP35DP1BB General Electric Range - Instructions

All Instructions for the JCBP35DP1BB
76 - 90 of 171

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Could not adjust heat on burner.
2 of 4 people found this instruction helpful.
  • Roy from Au Gres, MI
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Followed directions given by previous customers problems which we found on the internet.
Was this helpful?
Thank you for voting!
Element blew hole in self then no power to burner.
2 of 4 people found this instruction helpful.
  • Melvin from Portland, TN
  • Easy
  • Less than 15 mins
  • Screw drivers, Socket set
Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.
Was this helpful?
Thank you for voting!
temperature sensor went
1 person found this instruction helpful.
  • Alex R from Randoff, NJ
  • Easy
  • Less than 15 mins
  • Nutdriver
Took back panel off unplugged sensor and replugged in and worked like a charm!Sears wanted $400 and was going to 'overrepair"Got the 60 dollar part on here. UPS shipped to wrong address and customer service refunded my shipping and was excellent! would definetly use again!thanks
Was this helpful?
Thank you for voting!
Broken right END of oven door HANDLE (3 separate pieces assembled)
1 person found this instruction helpful.
  • Margaret from SARASOTA, FL
  • Very Difficult
  • 1- 2 hours
  • Pliers, Screw drivers, Wrench (Adjustable), Wrench set
(Followed the ORIGINAL manufacturer's instructions for assembly we retained when purchasing the appliance.) Replacing the broken handle end involved removal of the LEFT handle end as well as the broken RIGHT end, the center rod handle, and unscrewing the outer door face from the inner door face. Had to find specialty screwdriver for non-s tandard screw heads. Sigh. It was impossible to replace the door handle, as it requires removing the entire door - It is too heavy for one person to hold in place while the 2nd person tried to blindly replace screws thru a 1/2 inch slit in the outer and inner door pieces. Hiring a handyman is impossible leading up to the holidays, so we decided to just buy a new stove. Something that should be really simple to replace for less than $50 is now a major budget outlay due to a crappy design.
Was this helpful?
Thank you for voting!
Oven no longer working after running the self clean option. Only Stove top burners worked
1 person found this instruction helpful.
  • Dominick from THORNWOOD, NY
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
I began by turning off the breaker in the panel.
Slide the oven out into the open area.
Removed 3 screws in order to remove rear top panel.
Took 2 pictures of the wiring location on the PCB
Removed all wiring going to the circuit board total of 8.
Removed 4 screws in order to remove bad PCB.
Remove faceplate from bad PCB (you will need to place this faceplate on the new PCB.

To Install.
Reverse steps above
Was this helpful?
Thank you for voting!
BASE OF BULB BROKE OFF & WELDED TO SOCKET
1 person found this instruction helpful.
  • NEIL from ROCKY POINT, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
Was this helpful?
Thank you for voting!
Knob part broke on & off switch.Got a nee
1 person found this instruction helpful.
  • Sandra from Saint Johns, AZ
  • Very Easy
  • 15 - 30 mins
Got a new knob.
Was this helpful?
Thank you for voting!
Bake button stopped registering
1 person found this instruction helpful.
  • Ryan from COHOES, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
This was simple enough to repair for me, a relative novice. Just remember you need a nut driver to take the back panel off, take a photo of the existing board so you remember which wires go where, and you definitely need a hair dryer to heat up the sticker on the old board so you can remove it and put it on the new board.
Was this helpful?
Thank you for voting!
control switch had stopped working, burner wouldn't work properly
1 person found this instruction helpful.
  • Ruth from JACKSON, MO
  • Really Easy
  • Less than 15 mins
  • Screw drivers
took out a couple of screws and replaced with new switch, plugged in switch wires. very easy
Was this helpful?
Thank you for voting!
Rubber cracked
1 person found this instruction helpful.
  • Mark from ANDOVER, OH
  • Very Easy
  • Less than 15 mins
Took 5 minutes to repair easy peasy??
Was this helpful?
Thank you for voting!
THE FACE PLATE IS HARD TO GET OFF THE OLD CONTROL BOARD. USE A THIN KNIFE
1 person found this instruction helpful.
  • Melvin from WEBSTER, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
THE INSTRUCTIONS THAT COME IN THE EMAIL ARE VERY GOOD. BE SURE TO TAKE A PICTURE OF THE WIRING.
Was this helpful?
Thank you for voting!
Oven board went out
1 person found this instruction helpful.
  • Jackie from TICKFAW, LA
  • Very Easy
  • 15 - 30 mins
  • Pliers
One wire at at time then used my razor blade to get front off stuck right back on
Was this helpful?
Thank you for voting!
Hot burner light lens broke off.
1 of 2 people found this instruction helpful.
  • Charles from NEKOOSA, WI
  • Easy
  • 15 - 30 mins
  • Screw drivers
Pull range away from back wall. Remove panel behind control knobs by removing the screws that hold it on. Find hot burner light that holds lens. Remove broken part of lens. Insert new lens into hole on front of control panel and into hot burner light receptacle. Replace back panel. Slide range back into place.
Was this helpful?
Thank you for voting!
Change bulb
3 of 8 people found this instruction helpful.
  • Louis from LEAGUE CITY, TX
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Easy
Was this helpful?
Thank you for voting!
Surface element switch failed
1 of 2 people found this instruction helpful.
  • William W. from Seattle, WA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
Top front sloping sheet metal panel with all controls and plastic end caps has to come off. Need 2 people, one to hold it while other replaces switch. Problem was getting screw holes on bottom ends lined up and cuts from sheet metal edges. Ten minutes to get it apart, 40 to get it back together. New switch works fine.
Was this helpful?
Thank you for voting!
All Instructions for the JCBP35DP1BB
76 - 90 of 171