- Home
- JCBP35DP1BB
- Instructions
JCBP35DP1BB General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Drawer glide broken
3 of 3 people
found this instruction helpful.
-
TERESA from SALTVILLE, VA
- Very Easy
- 15 - 30 mins
-
Socket set
took nut driver to remove the old and replaced with new. simple.
Was this helpful?
Thank you for voting!
OVEN CLOCK CONTROL MALFUNCTIONED
3 of 3 people
found this instruction helpful.
-
Gregoire from N CHESTERFLD, VA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Wrench set
I turned off the circuit breaker and unplugged the stove. I removed the back panel and marked the location of the wires on the new oven clock control. I detached the wires and removed the old card. I installed the new one and reconnected the wires. I plugged the stove and turned on the circuit breaker. All the lights came on and the oven
... Read more
worked fine. I reinstalled the back panel and it took me less than thirty minutes to complete the job.
Read less
Was this helpful?
Thank you for voting!
The oven does not keep adequate temperature.
3 of 3 people
found this instruction helpful.
-
Michael from GILLETTE, WY
- Really Easy
- 15 - 30 mins
-
Nutdriver
Pull the range out from the wall to access the rear of the unit. Turn off power to the range by unplugging from the wall or turning off the breaker.
Remove the large back cover from the oven portion of the range. Locate the two small wires and connector which is located between the two connections for the broiler heating element. Unp ... Read more lug the small connector.
Open the oven door and remove the screw that holds the temperature sensor in place between the broiler heating elements on the inside of the oven. Gently pull the sensor and the wire connector through the hole and discard.
Feed the new connector and wire through the hole from the inside of the oven. Attach the sensor to the oven wall with the screw.
Go to the back of the unit and make sure that no insulation has gotten into the oven space. Re-route the new wire being careful not to let it touch the contacts for the broiler heating element. Reconnect the wires to the connector and replace the back cover of the oven.
Plug in the range or turn on the circuit breaker. Slide the range back into place and re-level the unit. Test the oven to make sure the temperature is accurate and will maintain temperature.
Remove the large back cover from the oven portion of the range. Locate the two small wires and connector which is located between the two connections for the broiler heating element. Unp ... Read more lug the small connector.
Open the oven door and remove the screw that holds the temperature sensor in place between the broiler heating elements on the inside of the oven. Gently pull the sensor and the wire connector through the hole and discard.
Feed the new connector and wire through the hole from the inside of the oven. Attach the sensor to the oven wall with the screw.
Go to the back of the unit and make sure that no insulation has gotten into the oven space. Re-route the new wire being careful not to let it touch the contacts for the broiler heating element. Reconnect the wires to the connector and replace the back cover of the oven.
Plug in the range or turn on the circuit breaker. Slide the range back into place and re-level the unit. Test the oven to make sure the temperature is accurate and will maintain temperature.
Read less
Was this helpful?
Thank you for voting!
blew out board by crossing wires..mistakenly toke out bulb assembly to replace bad bulb
3 of 3 people
found this instruction helpful.
-
Ken from CALABASH, NC
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Turne off power to range..pulled oven out..Took top back panel off with nut driver. 4screws .. Took picture of control board....removed bad control board with Phillips driver...4 screws....installed New board...removed 1 connection at a time and replaced in New board..Turned power on to test new board...check picture to make sure connect
... Read more
ions are correct...turn off power...put back panel back on...put range back in place...turn power back o n...done ..approximate time 15 to 20 minutes..
Read less
Was this helpful?
Thank you for voting!
burner not work
3 of 4 people
found this instruction helpful.
-
SILVIA from Midlothian, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers
Fue muy facil desconectar primero la estufa despues quite los tornillos de la parte superior detras de la estufa, desconecte un cable del switch y lo conecte en el nuevo despues el siguiente hasta conectar todos los cables en el nuevo switch. Lo mejor es desconectar uno por uno para mo mesclar los cables , despues removi el switch de la e
... Read more
stufa y puse el nuevo , puse las partes de regreso y listo conecte la estufa t revise si funcionava el quemador y listo sin ningun problema.
Read less
Was this helpful?
Thank you for voting!
old drip pans rusted
3 of 4 people
found this instruction helpful.
-
noreen from torrington, CT
- Really Easy
- Less than 15 mins
I unplugged the burner, lifted the old drip pan out, put new drip pan in, plugged burner in. The stove looks brand new and it took less than 2 minutes.
Other Parts Used:
Was this helpful?
Thank you for voting!
aged burner bowls
3 of 4 people
found this instruction helpful.
-
Louis from Sandwich, MA
- Really Easy
- Less than 15 mins
I just removed the range elements and old bowls, placed the new bowls into the range top, and inserted the heating elements. What surprised me was the quickness in filling the order. I had the new parts the next day! Great!
Other Parts Used:
Was this helpful?
Thank you for voting!
oven would not get hot
2 of 2 people
found this instruction helpful.
-
Paul from GATE CITY, VA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
ordered over the phone a new temp sensor. Un plug the oven, take off the back, open oven and unscrew the temp sensor, pull the sensor until the elec connector clip comes through so you can unclip the old sensor, clip on the new then pull the line back and re attach the sensor to the ovn. Plug in the oven.
Pretty simple, just hard t ... Read more o work inside the oven. I unclipped the sensor line outside the oven to make sure it would come apart first before I was working inside the oven.
Pretty simple, just hard t ... Read more o work inside the oven. I unclipped the sensor line outside the oven to make sure it would come apart first before I was working inside the oven.
Read less
Was this helpful?
Thank you for voting!
Oven temp wouldn't regulate.
2 of 2 people
found this instruction helpful.
-
Ronald from Crumpler, NC
- Very Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Followed the directions!
Was this helpful?
Thank you for voting!
lights blown out
6 of 14 people
found this instruction helpful.
-
Gerald from WINTERVILLE, GA
- Very Easy
- Less than 15 mins
replaced lights in refrigirator and freezer
Was this helpful?
Thank you for voting!
Broken drawer glider
2 of 2 people
found this instruction helpful.
-
James from RANCHO MIRAGE, CA
- Very Easy
- Less than 15 mins
-
Screw drivers
Took off broken part and replaced it with the new part by removing a Phillips head screw, the broken part, replace with new and reinstalling the same screw.
Was this helpful?
Thank you for voting!
Drawer support broke
2 of 2 people
found this instruction helpful.
-
Charles from BOULDER, WY
- Really Easy
- Less than 15 mins
-
Nutdriver
Remove drawer by pulling out and lifting up so drawer will slide out of range. Use 1/4 inch Nutdriver or socket - remove the screw that holds the drawer support to the body of the range. Remove support and install new one with screw Pay attention to the way the support fits. There are two holes one for the screw and the other for the plas
... Read more
tic prong on the bottom of the support. The prong fits in the bottom hole and the screw in the above hole.
Read less
Was this helpful?
Thank you for voting!
just needed new GE burner bowls
2 of 2 people
found this instruction helpful.
-
Jacqueline from E WENATCHEE, WA
- Very Easy
- Less than 15 mins
Only instructions I have has nothing to do with installation. But I'd like to suggest that you find a better shipping method. Placed my order on Feb. 7, received message later same day that it'd shipped. I didn't receive it until Feb. 16th -- very poor delivery service.
Other Parts Used:
Was this helpful?
Thank you for voting!
Drawer sticking and not operating smoothly
3 of 5 people
found this instruction helpful.
-
Bill from Philadelphia, PA
- Easy
- Less than 15 mins
-
Screw drivers
I was so sick of this drawer and I over heard a buddy telling a story about a website that you can get ANY piece for appliances. I take the drawer out, look up the website (partselect.com) look at the appliance diagram and find the missing piece. Order it, get it, install it. My wife thinks I'm a hero and I think I'm pretty cool too.
Was this helpful?
Thank you for voting!
Stove was not getting enough power.
2 of 2 people
found this instruction helpful.
-
Nathan from Wells, ME
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
My stove didn't seem to be getting enough power for the oven to heat up and the burners to get hot enough. When I checked the connection of the electric cord I found that one of the 3 terminals that the plug connects to was broken off. When the new part came I removed the old part by first disconnecting the 3 wires [black,white(ground),r
... Read more
ed] and then using a small but long 1/4 socket (that I found at Lowes)I removed the 2 screws that held the old part to the stove and the green screw under it holding the flat copper piece that also connects under the white ground wire of the part. I mounted the new piece on with the 2 1/4 screws. The new part comes with a piece of copper that is for grounding the part to the stove. When I compared it to the old part it was a little different. I first screwed the copper piece onto the stove (under the part) with the green screw then I screwed the white wire over the copper piece to the center terminal(you have to make the hole of the copper piece line up to the screw hole). I connected the other 2 wires and then connected the electric cord to the new terminal block and then put the back cover back on the stove and plugged it in. The clock came on I turned on the four burners they all got hot and red. I turned on the oven the element on the bottom got red I then turned on the broiler the top element got red. My stove is fixed.
Read less
Was this helpful?
Thank you for voting!