EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JCBP35DP1BB General Electric Range - Instructions

All Instructions for the JCBP35DP1BB
121 - 135 of 171

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Replaced All Burner Receptacles After One Failed And Also Replaced Ball Burner Bowls
  • ROBERT from MECHANICSBURG, PA
  • Really Easy
  • Less than 15 mins
This installation was for a replacement for one of the burner bowls on the original order. Replacement bowl fits proiperly.
Was this helpful?
Thank you for voting!
Burner bowls had been used and abused for year gone by in this rental.
  • Diane from Rio Rancho, NM
  • Really Easy
  • Less than 15 mins
Replaced them all. Next I want to replace the burners.
Was this helpful?
Thank you for voting!
Oven light wire broken, damaged socket
  • Patricia from Brandenburg, KY
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers
Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.
Was this helpful?
Thank you for voting!
burner control
  • hugh from sun city center, FL
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
installed new burner control w/knob. about 30 min. stove back in place. working fine
Was this helpful?
Thank you for voting!
Burner light would not go out.
  • Creed from Topsham, ME
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers, Socket set
Identified the switch that went bad. Order a new one and replaced it. The part came in a timely fashion and I am pleased with the result.
Was this helpful?
Thank you for voting!
needed to unstall "anti tilt" bracket on back of electric range to be code compliant for property..
  • Greg from Ft. Washington, PA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Turned off circuit breaker, Then pulled out range, straight out and away from wall and cabinets. Layed braket on flooring and moved stove back in to make certain it aligned with range rear stands. Moved range back out, marked holes in braket, screwed in screws to anchor bracket. Pushed range back into placed against wall. Tried to |"til t" range by pulling down on door after opened - range was held in place sre
Was this helpful?
Thank you for voting!
slot that heating element fits was worn down and caused burners to be uneven
  • Judith from Broadway, VA
  • Really Easy
  • Less than 15 mins
replaced with new ones
Was this helpful?
Thank you for voting!
6" and 8" burner bowl replacement
  • Shawn from Lubbock, TX
  • Really Easy
  • Less than 15 mins
Slide out burner elements. Remove old burner bowls. Insert new burner bowls and reinstall burner elements.
Was this helpful?
Thank you for voting!
Burner Switch Went Out
  • Jim from Prosser, WA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers
Turn off power at main electric panel/ move stove away from wall and unplug cord from outlet. Take knob off the front take two screws off the panel, take back panel off and remove the used switch and take and replace the wiring to the new one , one at a time wire for wire. Then put back tighter in reverse of the way you took it off. Plug in cord and move stove back to the wall. Easy
Was this helpful?
Thank you for voting!
surface burner would not work
  • julio from hobbs, NM
  • Really Easy
  • Less than 15 mins
  • Nutdriver
watched it on parts select this is a real fast and simple install took longer to pull the range out of its position well started by shuting off the power then double checked that the range was deenergized removed the knob then the 2 screws then on the rear of the range removed the back panel about 8 screws used a nut driver then removed t he old switch removed each wire one by one and pluged each wire into the new switch just as they were on the old switch the new switch was exactly the same so every thing matched up perfect installed the screws to the front which hold the swich in place then the back cover turned on the power and tested the switch every thing working ok done shut off power slid range back into its place turned power back on everything still ok
Was this helpful?
Thank you for voting!
bowls were worn out
  • frances from winston salem, NC
  • Really Easy
  • Less than 15 mins
Open the box and inserted the bowls
Was this helpful?
Thank you for voting!
oven continued to get F2, F3 and F5 error messages when ovewn got hot
  • Ralph from Redding, CA
  • Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set
This repair was quite a bit more difficult then what had been described on the web site. First off, I have a double wall oven that is built in. Sliding it out of the cabinet was difficult and because oven was hard wired, I had to disconnect the actual wiring from the oven back. . Positioning the oven and allowing for it to rest on a s upport bench was the most difficult part The oven is heavy. Eventually, removing the back and top panels of the oven revealed the sensor connection. I was then able to feed it through the oven and reconnect all the wiring harnesses.. Getting the oven back in the cabinet was equally a challenge. But it did seem to fix the problem with over heating.
Was this helpful?
Thank you for voting!
Oven Sensor Replacement
  • Barbara from Edwardsville, IL
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver
The part was just like the old one and would have been an easy fix except our range suffered from a lighting hit. The clips had melted together. Called a dealer and asked about a new wiring harness. He said in those cases just cut the clip off and hard wire with wire clips,or firecrackers. We used wire nuts and taped all together and the oven works just great. Nothing is ever as easy as it should be.
Was this helpful?
Thank you for voting!
Shorted Control Unit -
  • Gerald from Plantsville, CT
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Control unit was easy to remove ,wires color coded-the face plate(key pad) needed to be separated from the old unit. Carefully used a hair dryer to warm the decal. . . Secured the old unit gently in a vise, warmed ( and separated slowly, with a razor blade and thin putty knife(patience). . Once removed, applied to the new unit. . . 5 Stars to partselect for service. . . . Turned a $400 repair into $100 do-it your self. Partselect will be my 1st "go to" from now-on.
Was this helpful?
Thank you for voting!
Burner Would Not Turn Off
  • BILLY from WEBSTER, FL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Replace control switch
Was this helpful?
Thank you for voting!
All Instructions for the JCBP35DP1BB
121 - 135 of 171