J797D2 General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
No problems
1 person
found this instruction helpful.
-
Darlene from NORTH AUGUSTA, SC
- Really Easy
- Less than 15 mins
lift eye slide in bowl and trim ring, put the eye back down,
Other Parts Used:
Was this helpful?
Thank you for voting!
Old broil element was shorted out.
1 person
found this instruction helpful.
-
Vittorio from MATAWAN, NJ
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Unscrewed the 2 screws holding the old one in and the 2 bolts holding the bracket. Installed the new one in. 20 minutes.
Was this helpful?
Thank you for voting!
Customer service
2 of 4 people
found this instruction helpful.
-
Patricia from San Jose, CA
- Really Easy
- Less than 15 mins
Customer service is great. Fast shipping. Great communication. I have them bookmarked from a previous order. Same good service as the first time. Thank you.
Other Parts Used:
Was this helpful?
Thank you for voting!
Oven wouldn't heat
2 of 4 people
found this instruction helpful.
-
Peter from Sacramento, CA
- Really Easy
- Less than 15 mins
-
Nutdriver
First I shut off the circuit breaker for the oven then removed the screws that hold the element in place. The element was pulled out about 3 inches and unscrewed the 2 screws to disconnect the two wires. Upon receipt of the new element, I simply reversed the above process and the oven performed like new. Very easy, very quick and very
... Read more
grateful to have the oven operating again and it was a very inexpensive fix.
Read less
Was this helpful?
Thank you for voting!
Broiler element burned out
1 of 2 people
found this instruction helpful.
-
Alyce from Littleton, CO
- Really Easy
- Less than 15 mins
-
Nutdriver
The customer service at PartSelect.com is wonderful. They assisted me to located a part for a 40 year old oven. Took only a few minutes to take the old one out and put the new one in. Process was pretty self explanitory.
Was this helpful?
Thank you for voting!
Baking element broken in two
2 of 5 people
found this instruction helpful.
-
Diana from Galion, OH
- Really Easy
- 15 - 30 mins
-
Nutdriver
The baking element burned through, in my really old double oven. (It was in our home when we bought it 16 years ago.) It was the top oven element that broke. I wasn't sure it could be repaired. I looked on line and I found it. It took my husband less than 30 min. to fix it. I have my oven back but it would have nice to get a new one.
Was this helpful?
Thank you for voting!
Broken broiler element
1 of 2 people
found this instruction helpful.
-
Michael from Medford, NY
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Replacing the part was fairly simple. Do not forget to dis-connect the element from the back.
Was this helpful?
Thank you for voting!
broiler element not coming on
1 of 2 people
found this instruction helpful.
-
Michele from Roanoke, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
removed 2 nuts holding the element in the oven. removed 2 screws that secured the wires to the element. installed the new element in reverse.
Was this helpful?
Thank you for voting!
Replace cracked broiler element
1 of 2 people
found this instruction helpful.
-
Deborah from Middletown, CT
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench set
Unplugged Stove, pulled away from wall. With smaller wrenches, took the two screw-nuts off the inside back and above that hold the broiler element in place. Since it is an older stove...took the back panel off the stove with philips screw-driver which consisted of 10 screws. Once that was removed was able to unscrew the broiler element fr
... Read more
om the two wires that provide the electricity. Used the flash light when I had to unfasten the screw-nuts inside the stove because kitchen lighting wasn't strong enough.
Read less
Was this helpful?
Thank you for voting!
burned-out broiler element
2 of 5 people
found this instruction helpful.
-
William from Carmel, NY
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
turn off breaker in electrical panel....remove stove socket from outlet....remove rear panel from stove....undo wire connectios from broiler element....inside the oven, gently move thermostat wire out of the way....unbolt broiler plate from rear wall....remove broiler hanger and then broiler element....reverse procedure and you're all set
... Read more
.
Read less
Was this helpful?
Thank you for voting!
Door seal had large pieces missing
1 of 2 people
found this instruction helpful.
-
David from BROOKLYN, MI
- Difficult
- More than 2 hours
-
Nutdriver, Screw drivers, Socket set
I had to remove the door, burners, stove cooktop, both oven heating elements. Two j bolts in the rear of range hold oven box to range body and sandwich the seal in place. After removing the oven box the new seal could be installed, then reassemble everything.
Was this helpful?
Thank you for voting!
Top element burned out of oven.
1 of 3 people
found this instruction helpful.
-
Fred from Porter Ranch, CA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
Turned power off to oven. Unscrewed back plate exposing wires connected to heating element. It was difficult to unscrew the connections between them as it was hard to reach in because the oven door was in the way, but i finally succeeded. Unscrewed the bracket holding the burned out element and then attached the wires to the new element.
... Read more
Attached the bracket and I turned on the power. I then tested the oven and it worked.
Read less
Was this helpful?
Thank you for voting!
The broiler element had been broken for some time.
0 of 1 people
found this instruction helpful.
-
Susan D. from Holland, MA
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
The stove was new when we moved into our new home but opted to leave "our" stove in the basement until the one that came with the house had seen it's better days. The removal of the original element required the use an allen type of driver - it's removal was simple and the new element popped-into place without a problem and I refastened w
... Read more
ith the screws that came with the new element. The part arrived from PartSelect right on time, in good condition, and I would definitely do business with PartSelect again when I need to! My only complaint has nothing to do with PartSelect, it is the angle one must assume to refasten the part into place! Thank you, and I'll be back!
Read less
Was this helpful?
Thank you for voting!
Old Broiler Ekement burned out
0 of 1 people
found this instruction helpful.
-
Stacy from Houston, TX
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
The removal- replacement problem basically involves the shortness of the connector wires to the terminals. Because the burner is close to the top there is little room to use a screwdriver. The old unit used metal screws. The new came with open threaded holes in the terminals with two threaded screws. Used a small 1/4" ratchet which wor
... Read more
ked OK, but had to carefully bend the ends of the terminals to allow me to lower the element to an angle that would all room for ratchet action. (All design engineers should first have to work in maintenance before going to drawing board!)
S. Cooke, Houston Texas
S. Cooke, Houston Texas
Read less
Was this helpful?
Thank you for voting!
Broil Element
0 of 1 people
found this instruction helpful.
-
Richard from Concord, NH
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Replaced damaged element exercising the care suggested in repair comments by previous customers. Old unit had screws connecting the broiler element to the stove's electrical supply wires, which were difficult to remove due to old age. Just took a little extra care to ensure that supply wires were not damaged during disconnect and after re
... Read more
connecting the new element the broiler tested OK. It is once again broiling steak to perfection
Read less
Was this helpful?
Thank you for voting!