The drain pump had three screws. Frist unplug the machine and turn the water off. And unplug the hose for the Hot and Clod Water. Make sure their no water in the tub. Unplug the pipe from the Tub. The unscrew the nut for the connector. Then unplug the connector and be careful not to damage plug for the connector. Press the plug connector
... Read morewith your finger or long nose pliers . Then just hook the new plumb and you all set.
Read less
Was this helpful?
Thank you for voting!
Don’t do this, but we prop the washer lid open so it doesn’t get musty between use; we put a sock or something in there to prevent the striker fro closing. When a family member hops up on the washer to get to the highest shelf in the laundry closet it snaps! And the. The washer won’t function.
4 of 4 peoplefound this instruction helpful.
Heather from CHARLESTON, IL
Very Easy
Less than 15 mins
Screw drivers
REALLY easy- Just unscrewed the two screws with a Phillips, slid the old one out, the new one set in perfectly, and used the same screws to hold it in place. 2 minute task total.
Was this helpful?
Thank you for voting!
Solenoid valves on water inlet assembly leaking by the valve seats.
4 of 4 peoplefound this instruction helpful.
Joseph from GRANBURY, TX
Really Easy
15 - 30 mins
Pliers, Screw drivers, Socket set
1. Unplug washer. 2. Turn off water and disconnect hoses. 3. Remove control panel and set aside. It's held in place by 2 screws on the back. 4. Remove 2 screws to remove water inlet valve assembly. 5. Replace in reverse order.
Was this helpful?
Thank you for voting!
Water wouldn't drain
4 of 4 peoplefound this instruction helpful.
Kevin from ZOAR, OH
Easy
15 - 30 mins
Pliers, Socket set
Replaced water pump. Washer now works as new. Wife is now happy!
Was this helpful?
Thank you for voting!
Water inlet would not stop running after filling
4 of 4 peoplefound this instruction helpful.
Michael from D HANIS, TX
Really Easy
15 - 30 mins
Nutdriver
Two screws to take off rear panel. Slid control panel board back to unlock and laid forward. Exposed two more screws holding in water inlet. Removed and slid old water inlet out, new water inlet in. Attached two screws, control panel and rear panel and works perfectly. So much easier than I imagined!
Was this helpful?
Thank you for voting!
Water dripping into tub when washer was off
4 of 4 peoplefound this instruction helpful.
Michael from ELBERTA, AL
Really Easy
15 - 30 mins
Nutdriver
Removed the top assembly where the controls are located by removing the two mounting screws, one on each side. Removed the two hoses. Removed the two mounting screws, Removed old part, installed new part in reverse order.
Was this helpful?
Thank you for voting!
Washer would not start
6 of 10 peoplefound this instruction helpful.
Jack from KENT, OH
Difficult
1- 2 hours
Nutdriver, Screw drivers
The parts I ordered were made of junk plastic and did not match up with the the existing parts. The parts did not end up fixing the problem and I bought a new washer instead.
Being a woman I had to figure out tipping it in its front. I put it on a dollie and drop it down real easy. Removed all water lines after water was shut off. Removed bolts. Removed bolts on plate to the right to unplug old pump. Plugged in new one and replaced all bolts, hoses and tipped her back up. Works like a charm a
... Read morend I saved $408 by doing it myself!!!!!
Read less
Was this helpful?
Thank you for voting!
Wash machine would not drain/pump water out of machine.
4 of 5 peoplefound this instruction helpful.
Jeff from FOLEY, MN
Easy
30 - 60 mins
Pliers, Socket set
1 Disconnect power 2) Cut water supply to washer 3) Disconnect water supply hoses from supply. ***if pump broke with water in tub, remove water from tub. 4) tip machine onto it's front side 5) remove hose clamp of exhaust hose & then remove exhaust hose from pump 6) Remove pump with socket/ratchet 7) disconnect pump electrical plug
... Read more 8) tell old pump to take a hike & throw in garbage 9)Iinstall new pump 10) Do steps 7—1 in reverse order to put back into business.******Be prepared to do it again in 6 months; I havnt had good luck!
Read less
Was this helpful?
Thank you for voting!
belt was about an inch loose from 4 years of washing clothes
3 of 3 peoplefound this instruction helpful.
Arnold from FRESNO, CA
A Bit Difficult
30 - 60 mins
Nutdriver, Screw drivers
Disconnected power and water, laid it on its back, took off the belt, then took the new belt and put it on with a little difficulty putting the belt back on. really have to watch your fingers if you are not careful
Was this helpful?
Thank you for voting!
Would not spin
3 of 3 peoplefound this instruction helpful.
Ricky from KRUM, TX
Really Easy
15 - 30 mins
Screw drivers
Took 4 screws out of back of control panel. Tested old capacitor. Installed new one. Put back on tested spin cycle everything is doing great
Was this helpful?
Thank you for voting!
The washer did not drain. It also did not click or sound like the drain cycle was being engaged.
3 of 3 peoplefound this instruction helpful.
Lindy from LILLINGTON, NC
Easy
30 - 60 mins
Emptied the washer, took the back cover off, tipped it foward, unplugge the old pump, remove two mount bolts. The replaced the new pump. The new pump resolved the issue.
My Orders
