- Home
- GLEF388GBA
- Instructions
GLEF388GBA Frigidaire Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
No Power to the Oven
1 of 3 people
found this instruction helpful.
-
Tony from Hartford, CT
- Really Easy
- Less than 15 mins
-
Screw drivers
Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.
Was this helpful?
Thank you for voting!
Lens cover for oven light broke.
0 of 1 people
found this instruction helpful.
-
Amy from Corona, CA
- Really Easy
- Less than 15 mins
Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.
Was this helpful?
Thank you for voting!
Convection fan making noise
0 of 1 people
found this instruction helpful.
-
Willis from Friendsville, TN
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
Removed old fan and replaced with new fan. To replace fan, the over interior fan blade was removed, then the two slip on wires were removed from the old fan motor, then the three screws securing the old fan motor were removed. The process was reversed to install replacement fan
Was this helpful?
Thank you for voting!
Broil Element shorted out
0 of 1 people
found this instruction helpful.
-
Frederick from Pompano Beach, FL
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I unplugged the Stove/Oven electrical cord from the wall, then removed the oven door by unlocking the door brackets with a flat head screw driver then closing the door to the last position before it closes and removing the door from the stove (found instructions on YouTube - very easy, which is optional), then removed the oven racks. Rem
... Read more
oving the door made it a lot easier to access the broil element and element support bracket screws using a socket wrench. I removed the screws from the rear cover on the back of the stove with a socket wrench to access and disconnect the broil element wires with my hand (pliers if needed). I removed the old broil element and inserted and reconnected the new broil element wires, then re-installed the rear cover. I tightened the broil element in place then re-installed the element support bracket and screws, replaced the oven racks, re-installed the oven door and plugged the stove into the wall. This took about twenty minutes and the broil element is working fine.
Read less
Was this helpful?
Thank you for voting!
Cracked inside glass
0 of 2 people
found this instruction helpful.
-
patti from Greer, SC
- A Bit Difficult
- 1- 2 hours
-
Screw drivers
I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti
Was this helpful?
Thank you for voting!
Control will not work - only clock blinks
0 of 4 people
found this instruction helpful.
-
Sue from Lampasas, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.
Was this helpful?
Thank you for voting!
Broken globe in oven and burnt out light bulb
0 of 5 people
found this instruction helpful.
-
Sharon from Foley, AL
- Really Easy
- Less than 15 mins
Easy as 1-2-3
Other Parts Used:
Was this helpful?
Thank you for voting!
element quick working
1 of 9 people
found this instruction helpful.
-
Kathy from Shepherd, MT
- Easy
- 15 - 30 mins
-
Screw drivers
Ordering the part was easy.
Was this helpful?
Thank you for voting!
Heating element would not heat
-
Rita from Somerset, KY
- Easy
- 15 - 30 mins
-
Socket set
Took bolts out of back of oven ,pull out element had take electric clips off .Then I just plugged in the element ,push in and tighten up bolts. Turn oven on IT Works Yea!!!!!
Was this helpful?
Thank you for voting!
burner would not heat up
-
MARGARET from MILFORD, PA
- Really Easy
- 15 - 30 mins
-
Screw drivers
simple, removed a few screw's, unplugged old burner, plugged in the new one. that was basically it. easy!
Was this helpful?
Thank you for voting!
burner wouldn't heat up
-
Stephen from Columbia, SC
- Easy
- 15 - 30 mins
-
Nutdriver
I unplugged the stove. Then I lifted up the top of the stove to expose the burners. I unscrewed the necessary screws and plugs that attached the old burner to the stove. Then I simply put the new one back in it's place. The stove was one of those flat burner stoves, and I was a little concerned that I would be able to do it. The repair m
... Read more
an wanted to charge me $150.00 for labor.
Read less
Was this helpful?
Thank you for voting!
Small plastic lens on control panel broken.
-
James from Louisville, KY
- Really Easy
- Less than 15 mins
-
Nutdriver
Pulled the range out, unplugged it, removed upper back panel, inserted lens through front of control panel, slid the notch on the actual light onto the lip on the back of the plastic lens. Done!
Was this helpful?
Thank you for voting!
no heat
-
John M. from PLEASANT PRAIRIE, WI
- Easy
- Less than 15 mins
-
Nutdriver
Replaced the oven probe because a no heat problem. also had to replace the oven control. That was a bit expensive but still saved me hundreds not calling a serviceman. By the way, it works like new.....
Was this helpful?
Thank you for voting!
Needed to install an anti-tip bracket on my stove.
-
Daniel from Provo, UT
- Really Easy
- Less than 15 mins
-
Socket set
Moved the stove. Used the template to position the bracket. Put the supplied screws to attach bracket to the floor. Slid stove back into place. DONE!
Was this helpful?
Thank you for voting!
Oven not heating up properly
-
Larry from Jordan, AR
- Really Easy
- Less than 15 mins
-
Nutdriver
I removed back cover and replaced the probe. The troubleshooting info indicated this is the problem 99% of the time. Guess what, it did not help! Further checks indicate that broil element may be out. Am going to resistance check and order if that is the problem.
Was this helpful?
Thank you for voting!