EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

GDF520PSJ0SS General Electric Dishwasher - Instructions

All Instructions for the GDF520PSJ0SS
121 - 135 of 151

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dishwasher did not dry dishes
3 of 6 people found this instruction helpful.
  • Teresa from DETROIT, MI
  • Easy
  • 30 - 60 mins
  • Socket set
Followed directions on YouTube
Was this helpful?
Thank you for voting!
washer would nt ru it beeped 3x and flash start lite
2 of 3 people found this instruction helpful.
  • Robert from ST AUGUSTINE, FL
  • Easy
  • 30 - 60 mins
  • Screw drivers
Looked upm the problem it said door wasn.t closed so cause was the door latch. put in the new one no change so I bought a new dishwasher
Was this helpful?
Thank you for voting!
Door gasket at bottom of door was falling apart and leaking
2 of 3 people found this instruction helpful.
  • Alvin from SCHENECTADY, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
1. Shut off circuit breaker power
2. remove toekick
3 .disconnect door wire harness at bottom of main control board
4. release 2 wire ties securing harness to tub using long nose pliers
5. remove 2- 1/4 in. hex head screws from bottom of door
6. insert 5/32 in Allen wrench through existing holes in front leg and h inge arm when door is partially opened.(about 1/4 of the way)
7. repeat step 6 on both sides (this locks door partially open)
8. lift door up about 3 in. then tilt door in and remove door completely
9. slide old gasket out and replace with new gasket
9. reassemble door
Was this helpful?
Thank you for voting!
Leaking under door
2 of 3 people found this instruction helpful.
  • Josef from MT CARMEL, TN
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Since I have granite countertops, unscrewed 2 screws on each side of cabinet. Unscrewed the toe plate, unplugged the wire connector, and disconnected the cable
from the door which was held by tie wraps. Pulled out dishwasher about a foot. Unhooked the spring cable to the door, lifted the door out and placed it on a spare table. Wit h door face down on a towel, I unscrewed the screws at the bottom to release the latches, then unscrew the screws that hold the door locked in place. Turned the door on its back face up, wedged a flathead driver to release the settings display, from the body of the door. Separated the 2 panels replaced the foam rubber vent seal. Placed the face face down, reconnected both pieces of the door together pushing down. Rescrewed the bottom to lock the 2 pieces together reinsert the hinges, screwed them in with nutdriver1/4". Grabbed the old gasket, replaced it with new one, sliding it into the groove on the bottom inside of door. Reattached the door to the washer, rehooked the cables to the door, retired with zip ties the cable to the underside of door, reinstalled the wire connector, and re screwed the toe plate. Pushed the dishwasher, leveled, rescrewed into cabinet. Replaced the tub gasket.
Was this helpful?
Thank you for voting!
Dishwasher would not know door was closed
1 person found this instruction helpful.
  • Lesa from BETHALTO, IL
  • Very Difficult
  • 30 - 60 mins
  • Pliers
Parts diagram shows Striker can be popped out with screwdriver. Not true. It has a screw bolting it internally. Impossible to get to unless you disassemble the entire door. We took a power drill and small drill bit and bore it out like a cavity in a tooth. Needle nose pliers to extract the screw. Pretend your a dentist. Fixed it in 5 minutes. Replacement fit tight. A+
Was this helpful?
Thank you for voting!
DISHWASHER DIDN'T RESPOND TO SWITCHES. WON'T RUN.
1 person found this instruction helpful.
  • Dan from Page, AZ
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Screw drivers, Socket set
1. REMOVE LOWER FRONT KICK PANEL.
2. CHECK FOR 14VOLTS BETWEEN PIN 2 AND PIN 5= NO VOLTAGE.
3. LOWER CONTROL BOARD PANEL
4. REPLACE ELECTRONIC CONTROL BOARD.
5. CHECK FOR PROPER OPERATION.
Was this helpful?
Thank you for voting!
Heating element broke off and burned a hole in rubber tube, leaking water.
1 person found this instruction helpful.
  • Mario from CHESAPEAKE, VA
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Replaced the dishwasher with a new one! used the same brand (GE) but different model to make the job a little easier, first cut power to the outlet, disconnected electrically from dishwasher, cut off water source from dishwasher, and disconnected hose from garbage disposal, removed old dishwasher put new one in, connected electrical wires (color coded), connected water supply with pliers, and connect your hose to your disposal and level your new disposal with leveling screws that comes with the new dishwasher. Put front cover plate on with screws provided with a screwdriver and that's it.
Was this helpful?
Thank you for voting!
Not drying dishes
1 person found this instruction helpful.
  • Paul from STEWARTSVILLE, NJ
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
Installed new heater by pulling unit out of it’s cubby hole. Was able to gain access to the nuts that hold it down and make the seal, as well as the electrical connections. Re-installed. Helpful if you remove both dish baskets and utencil basket for access when installing heater.
Was this helpful?
Thank you for voting!
Heating Coil was inoperable
1 person found this instruction helpful.
  • Robert from AUGUSTA, GA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
My heating coil was not working so naturally I thought I needed a new coil and ordered one accordingly. During the time it took to ship to me, I did more research and people suggested testing the coil with and ohmmeter for resistance as often times the coil is fine and it is the flood switch that is the problem. I got an ohmmeter and chec ked the old coil and it returned readings that were just fine (btw 15-30), so I returned the coil and ordered this flood switch.

Anyone reading this debating between buying the coil and switch can save themselves a lot of trouble/time/money by removing the coil and testing it first.

The installation of the flood switch is fairly simple. There's a great video on Youtube for it (titled "GE Dishwasher not Drying Dishes - How to Replace Bad Flood Switch:), so I won't walk through the step-by-step on it.

However, one word of advice is to be careful when installing so that you don't let the o-ring on the switch slide down the connector/wire once you connect them or you'll get a slow leak into the catch pan at the bottom.

Also, if this if your first repair on a GE Dishwasher then get to know the unit while you have it pulled out. It won't be your last repair based on my experience...
Was this helpful?
Thank you for voting!
Door would not shut, machine would not run.
1 person found this instruction helpful.
  • Deborah from BRADENTON, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Took out 2 screws that held machine in cabinet. Pulled out dishwasher about 4 inches. removed old latch and disconnected electric connection. Put in new latch, reconnected electric connection, replaced screws, pushed machine back in cabinet, replaced 2 screws that hold machine in place. Works like new!
Was this helpful?
Thank you for voting!
Lower arm spay was breaking apart
1 person found this instruction helpful.
  • Carol from Toms River, NJ
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Followed instructions used flat head screwdriver to unlach old arm. Took out and put in new spray arm. Really easy
Was this helpful?
Thank you for voting!
snapped new spray arm in place
1 person found this instruction helpful.
  • Timothy from Pedro, OH
  • Very Easy
  • Less than 15 mins
snapped new spray arm in place
Was this helpful?
Thank you for voting!
Top tray rusting
1 person found this instruction helpful.
  • Leland from Celina, TX
  • Very Easy
  • Less than 15 mins
Ordered new one, pulled old off, pulled arm off, attached new tray and attached washer arm. Easy!
Was this helpful?
Thank you for voting!
Dishwasher ceased to fully drain after full cycle
1 person found this instruction helpful.
  • David from RIVERVIEW, MI
  • Easy
  • Less than 15 mins
  • Nutdriver, Pliers
First, drain as much water as possible using a shop vac or siphon. Unscrew two plastic lugs and food screen to release the metal *disk* found inside the dishwasher at the bottom. Then, remove the grey retainer ring found under the food screen.
Using the nut driver, remove two screws from the white plastic retainer ring at bottom th e flood switch.
I used pliers to grip the ring to take it out.
**Dry everything in the "well" where the flood switch sits.**
Now, remove the bottom front cosmetic panel. This exposes the underside of the appliance. Locate the flood switch wire underneath and gently pull down the small black plastic tab which holds the wires in place. This allows more movement to make your job a little easier!
Pull up on the flood switch and simply unplug it and swap in your new switch! Replace everything as you found it, don't over-tighten your screws, and make your kids load that sucker! Hope this helps, and have a beautiful day!
Was this helpful?
Thank you for voting!
The blue colored silverware holders had broken pegs at the ends.
1 person found this instruction helpful.
  • Tom from BEND, OR
  • Very Easy
  • Less than 15 mins
Removed the old assembly and put the new one in. Took about 15 seconds. Perfect replacement. This assembly is the complete basket. The color of the blue silverware holders changed to grey which is not an issue at all unless that was the reason you bought this dishwasher in the first place. ;-)
Was this helpful?
Thank you for voting!
All Instructions for the GDF520PSJ0SS
121 - 135 of 151