- Home
- GDF520PSJ0SS
- Instructions
GDF520PSJ0SS General Electric Dishwasher - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The heating element on our dishwasher burned the lower spray arm, melting it in 2 pieces
4 of 5 people
found this instruction helpful.
-
Jake from SACRAMENTO, CA
- Very Easy
- Less than 15 mins
Simply unscrewed the old damaged arm and screwed the new one on, took less than a minute
Was this helpful?
Thank you for voting!
No water in dishwasher
4 of 5 people
found this instruction helpful.
-
Ryan from Saint Joseph, IL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers
It took longer to uninstall and reinstall the dishwasher than it did to change out the part
Was this helpful?
Thank you for voting!
Broken door latch and springs were not connected.
4 of 5 people
found this instruction helpful.
-
Mike from LAS VEGAS, NV
- Really Easy
- 15 - 30 mins
-
Screw drivers
Looked up the replacement part on YouTube, watched a video and followed the instructions. Part ordered was the correct part and the video showed how to access for replacing. Watched a different video for hooking up the disconnected springs that allow the door to lower and close smoothly. Whole process for repairs was less than 30 minut
... Read more
es.
Read less
Was this helpful?
Thank you for voting!
Dispenser no longer opened during wash cycle
4 of 5 people
found this instruction helpful.
-
Maurice from SAN JOSE, CA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Very straight forward. After removing the power source the dishwasher was pulled forward enough to access the the door hinge springs. Then the door could be removed and the inner skin separated to access the the dispenser mounting screws.
Was this helpful?
Thank you for voting!
Lower spray arm had melted tips
4 of 5 people
found this instruction helpful.
-
Ed from TRAVELERS RST, SC
- Really Easy
- 30 - 60 mins
A quick twist of the locking nut
Was this helpful?
Thank you for voting!
seals were leaking (they'd been chewed on by a mouse)
3 of 3 people
found this instruction helpful.
-
Tim from South Charleston, WV
- Really Easy
- 30 - 60 mins
the hardest part was removing the door from the face of the washer. Getting the door off required accessing the sides, so I had to lower the feet so it would slide out of the recess it sits in.
Disconnecting the springs for the door was straight forward and simple. once those were disconnected, it lifted off the hinges easily. ... Read more The seals themselves were simply press-fit into the recesses. the old ones pulled loose cleanly and easily.. the new ones pressed into place very simply and without any real effort.
Getting the door back on was a little problematic, mostly in getting the hinge pins to line up properly.. but once it settled in, it line up itself, and the springs were easily replaced. I re-leveled the dishwasher, and then ran it for a full cycle to ensure it wouldn't leak anymore.
Disconnecting the springs for the door was straight forward and simple. once those were disconnected, it lifted off the hinges easily. ... Read more The seals themselves were simply press-fit into the recesses. the old ones pulled loose cleanly and easily.. the new ones pressed into place very simply and without any real effort.
Getting the door back on was a little problematic, mostly in getting the hinge pins to line up properly.. but once it settled in, it line up itself, and the springs were easily replaced. I re-leveled the dishwasher, and then ran it for a full cycle to ensure it wouldn't leak anymore.
Read less
Was this helpful?
Thank you for voting!
No heat in both water and air
3 of 3 people
found this instruction helpful.
-
Alvin from SCHENECTADY, NY
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
Followed troubleshooting procedure to determine that defective Flood Switch caused the problem and not the Heating Element. Replaced only the Flood Switch. I also replaced a deteriorated door gasket.
De-installed dishwasher from cabinet, removed door, and tipped unit over with back of tub resting on floor.
I follow ... Read more ed the document referenced here for the troubleshooting and repair procedures: GE Appliances Technical Service Guide, 2012 GE Dishwasher, 31-9226.pdf available on web.
De-installed dishwasher from cabinet, removed door, and tipped unit over with back of tub resting on floor.
I follow ... Read more ed the document referenced here for the troubleshooting and repair procedures: GE Appliances Technical Service Guide, 2012 GE Dishwasher, 31-9226.pdf available on web.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Dishwasher Not Draining
3 of 3 people
found this instruction helpful.
-
Ivan from MANSFIELD, TX
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
The pump went out after a few months of very loud noise during the drain cycle and then one day no drain or noise. A bit of research shows that this pump goes out frequently on this model so I ordered a new pump after inspecting the old pump for a clog or snag on the rotors.
The Install:
After removing the dishwasher from ... Read more it's installed location and turning it on it's side (unplug water and electric of course), I was able to remove the pump from the two lines that connected it to the dishwasher and the drain line. I also had to unplug the pump from an electric connection to the dishwasher. Swapping out the new pump was the same but in reverse. Not a hard install, only simple tools required.
One note, my electric connection to the dish washer was different on this model pump since they changed the original part but there is an adapter included with this part so make sure it is in the box and fits before beginning.
The Install:
After removing the dishwasher from ... Read more it's installed location and turning it on it's side (unplug water and electric of course), I was able to remove the pump from the two lines that connected it to the dishwasher and the drain line. I also had to unplug the pump from an electric connection to the dishwasher. Swapping out the new pump was the same but in reverse. Not a hard install, only simple tools required.
One note, my electric connection to the dish washer was different on this model pump since they changed the original part but there is an adapter included with this part so make sure it is in the box and fits before beginning.
Read less
Was this helpful?
Thank you for voting!
The machine has no response to any operation.
3 of 3 people
found this instruction helpful.
-
Yongxin from CARROLLTON, TX
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
I replaced the User Control and Display Board and it is working very well now. The important things that should be noted are to take off the door and to open the door cover by unscrewing it. Those screws are located at the bottom of the door and two are hided inside.
Was this helpful?
Thank you for voting!
Door did not latch, therefore would not operate
5 of 9 people
found this instruction helpful.
-
Dawn from JAMESTOWN, TN
- Really Easy
- 30 - 60 mins
-
Screw drivers
Replaced latch
Was this helpful?
Thank you for voting!
Dish washer would not turn on
4 of 6 people
found this instruction helpful.
-
Patrick from BROOKFIELD, WI
- Very Easy
- 15 - 30 mins
-
Screw drivers, Socket set
took off 2 sheet metal on the bottom, lowered the dish washer, pulled it out enought to unscrew 2 screws, unplugged the old part plugged in the new, put it back together.
Works like a champ.
Works like a champ.
Was this helpful?
Thank you for voting!
soap did not dispense correctly
3 of 3 people
found this instruction helpful.
-
LaRay from PRESCOTT, AZ
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
Followed video instructions step by step.
I was fortunate i had enough slack in water, electric and discharge lines to avoid disconnecting.
Two wrinkles
1. wire clips on my door had to be pulled/pried loose from door and there were two not one
2. could not slide dishwasher out after lowering adjusters and ... Read more figured out it was the mounting tabs bumpimng the granite countertop, thus the use of putty knives to slide the dishwasher out.
I was fortunate i had enough slack in water, electric and discharge lines to avoid disconnecting.
Two wrinkles
1. wire clips on my door had to be pulled/pried loose from door and there were two not one
2. could not slide dishwasher out after lowering adjusters and ... Read more figured out it was the mounting tabs bumpimng the granite countertop, thus the use of putty knives to slide the dishwasher out.
Read less
Was this helpful?
Thank you for voting!
REPLACE DOOR CABLE
3 of 3 people
found this instruction helpful.
-
Lonnie from YUKON, OK
- Really Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
Removed the top two screws that hold the dishwasher to the cabinet , remove the two screws on the bottom panel and remove the panel. Screw the levelers all of the way up and pull out the dishwasher about 6 to 8 inch. Hook the new cabe on the spring and pull around pulley and attach it to the door bracket. I replaced both cables. Reverse
... Read more
to complete.
Read less
Was this helpful?
Thank you for voting!
Mid Spray Arm Assembly not spinning
3 of 3 people
found this instruction helpful.
-
Robert from FLUSHING, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
The Mid Spray Arm Assembly was not spinning due to a dish that was in placed the dishwasher that was too high and hitting the arm. When it spun until it broke the center shaft. Replacement was easy. After removing power I pulled the upper tray out and removed the Conduit Mid Tiered Assembly by unsnapping it from the tray. I twisted of
... Read more
f the broken spindle of the damaged arm assembly from the Conduit Mid Tiered Assembly and inserted the new arm and gently pushed it until it snapped into the Mid Tiered Assembly. Reinstalled the assembled parts by snapping into the tray making sure it was centered.
Read less
Was this helpful?
Thank you for voting!
Water was leaking at the bottom of the door
3 of 3 people
found this instruction helpful.
-
Brian from GRAND MARSH, WI
- Very Easy
- Less than 15 mins
The old gasket pulled right out with no tools needed,
The new gasket went in the same way.
Results:
It did help on one side, but the bottom gasket also needs to be replaced it has a couple of tears one on each end.
Next Steps:
When the bottom gasket gets here I will replace that and it should be as g ... Read more ood as new.
The new gasket went in the same way.
Results:
It did help on one side, but the bottom gasket also needs to be replaced it has a couple of tears one on each end.
Next Steps:
When the bottom gasket gets here I will replace that and it should be as g ... Read more ood as new.
Read less
Was this helpful?
Thank you for voting!