ESD3492H Caloric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
One burner didn't work all the time the other would go red hot
15 of 16 people
found this instruction helpful.
-
Phillip from Pekin, IL
- Really Easy
- 15 - 30 mins
-
Screw drivers
I unplugged the stove from the outlet, then removed the two burners I was going to be working on and the drip pans. Then I raised the top part of the stove and removed the screws holding the plug-in blocks to the stove. Then I cut the two wires going to the old plug-in block and stripped the wires back to match the new wire parts. Then I
... Read more
placed the sleeves over the new wires, then I placed the new wire beside the wire I stripped on the stove and screw on the wire cap making sure it was tight. I repeated this three more times, once I had all four wires connected I then placed the sleeves over the connections and heated them up until they were formed around the connection. Once I had all the connections done I placed one wire at a time into the plug-in block until it locked into place ( I looked at my old plug-in blocks first to make sure I placed the new wires in the correct way ).I then used the metal mounting bracket that matched my old ones and snapped the correct one onto each plug-in block. Before mounting them onto the stove I compared them to my old ones to make sure they were correct. Then I used the new screws to mount them to the stove. I took a second look at everything I had done before closing the top cover of my stove. After lowering the cover back into place I put both the drip covers in place and then installed the burners.I then plugged the stove back into the outlet and tried the burners. This was very simple and the video on the web site shows this very well which made my job very simple.
Read less
Was this helpful?
Thank you for voting!
Broiler burned out
8 of 8 people
found this instruction helpful.
-
David from Lewisburg, TN
- Easy
- Less than 15 mins
-
Screw drivers, Socket set
The Job didn’t take very long at all. I pulled the unit out and unplug it before I started the repair. I had to remove the back two access cover plates to get to the two wire leads that connect the broiler. I don’t believe there was enough wire to be able to do it all from the front side. Next I disconnected the two wires that connected i
... Read more
t while remembering what color goes to the correct side (just incase this does matter). After removing the wires I moved on to remove the element with a Philips screwdriver. The new part already had the hangers on it so I reused the old screws and installed the new element. Next I reconnected the wires in the back and re-installed the back panels. I plugged it up and it works as good as new now. This was definitely a lot cheaper to fix this myself than hire a repairman.
Read less
Was this helpful?
Thank you for voting!
The bake element burned in half, shorted out, made the lights in the house flick and burst in to a short lived flame.er
7 of 7 people
found this instruction helpful.
-
Michael from Winchendon, MA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Exactly:
(e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)
(e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)
Was this helpful?
Thank you for voting!
Electric burners where consistently intermittently working right. Sometimes they would work on High but not able to adjust to low heat. Sometimes they would just not want to come on at all. Occasionally there was a spark at the connection. If I jiggled the element just right it may or may not wo
7 of 9 people
found this instruction helpful.
-
JOAN from Pickford, MI
- Easy
- 15 - 30 mins
-
Screw drivers
Thought we was going to have to replace the range all together, due to most parts not being available for this model anymore. Since this is an expensive model, we did not look forward to having to replace it. So I thought just by chance I would check to see if anyone had parts to help in repairing it. Part Select did happen to have the
... Read more
Surface Plug-in block kit that was needed. After going at least a year with this problem, I am sooooo happy to say it is finally fixed and working great! Thanks much Parts Select.
Read less
Was this helpful?
Thank you for voting!
Electric burner on stove would not work
5 of 5 people
found this instruction helpful.
-
Ronald from Fresno, CA
- Easy
- 30 - 60 mins
-
Screw drivers
The first thing I did was to turn the power off to the stove by turning the Stove circuit breaker off at the Main breaker panel. I next removed the 4 burners by pulling them out of their plug-in blocks. I then removed the four screws that held the top of the stove to the body so I could access the bad plug-in block, the screws were loca
... Read more
ted under each of the burners drip pans. I next removed the screw holding the bad block. I lifted up the top of the stove so as to relocate the bad block, with wires connected, through the opening of the back burner. The bad block was located in the front rt part of the stove and by rerouting this to the back I could lay the top down and have easy access to what I needed to replace. I next used the knife to make a cut down the length of the old shrink tubing so as to gain access to the old splice. I next removed the old wire nuts which allowed the removal of the bad block. I then install the new clips into the new block. I installed one each shrink tubing onto each of the pigtails from the new clips and twisted the one new wire to the stove wiring harnes were the old wire was connected . I connected the seconded wire in the same manner. I pulled on each wire to verify that they were tightly secured together. I then positioned each shrink tubing over each wire nut (you have to fold the wire nut and wires down against the wire so as the shrink tubing will slip over the wire nut) and used a heating tool (hair dryer on high) to shrink the tubing around the wire nutted connection. I next installed the metal clip that would hold the block to the stove top. I placed the new block back to the location where the old block came from and secured it with the new screw provided by the kit. I re-installed the four screws to hold the top down, plugged in the four burners, turned the power on at the breaker box and turned the burner on to test that it work.
Read less
Was this helpful?
Thank you for voting!
not proper heat in oven
5 of 6 people
found this instruction helpful.
-
Mary from Raytown, MO
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
ordered part -got it the next day- stalled as long as I could then opened oven removed racks-used screwdriver to loosen screws in bracket holding element on- pulled out element-used pliers to take off wires in element-thew old element as far as possible-reversed procedure to put in new element-replaced rack-received praises of all afffect
... Read more
ed-the end
Read less
Was this helpful?
Thank you for voting!
Electric stove burners working intermitantly.
4 of 4 people
found this instruction helpful.
-
Michael from St. Louis, MO
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
replaced old, worn blocks with new style surface plug in block kits - all 4 burners. Completely resolved the problem at very low cost (less than $50.00).
Was this helpful?
Thank you for voting!
broken prong that knob fit onto
7 of 14 people
found this instruction helpful.
-
Lisa from Oklahoma City, OK
- Really Easy
- 15 - 30 mins
-
Wrench set
This was a piece of cake! We put off doing this for ourselves because we thought it would be difficult. We sold the house and "had" to do it. Turns out we should have done it for ourselves a long time ago.
Was this helpful?
Thank you for voting!
Sparks emitted at burner connection and burner does not work.
4 of 5 people
found this instruction helpful.
-
Doug from Puyallup, WA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
1. Turn off circuit breaker, pull out element and remove reflector pan.
2. Unfasten terminal block mounting screw and remove terminal block from casing.
3. Cut wires as close to defective terminal block as possible (not as per instructions) since you will need the maximum possible length of wire.
4. Slip on heat shrink slee ... Read more ves, strip stove wires and connect to new terminal block per instructions.
5. Heat shrink sleeves per instructions.
2. Unfasten terminal block mounting screw and remove terminal block from casing.
3. Cut wires as close to defective terminal block as possible (not as per instructions) since you will need the maximum possible length of wire.
4. Slip on heat shrink slee ... Read more ves, strip stove wires and connect to new terminal block per instructions.
5. Heat shrink sleeves per instructions.
Read less
Was this helpful?
Thank you for voting!
Broil element broke
4 of 5 people
found this instruction helpful.
-
Randall from Cartersville, GA
- Really Easy
- Less than 15 mins
-
Screw drivers
Top (broil) element broke in two on oven. Ordered part,it was there in three days. Quick fix, removed screw holding element to oven wall, unplugged wires, then just swaped out elements. Re-attached wires just as they were on old element and screwed back into same place and oven is working again.
Was this helpful?
Thank you for voting!
Broiler Element went out
3 of 3 people
found this instruction helpful.
-
Michele from Salem, OR
- Easy
- Less than 15 mins
-
Screw drivers
I unscrewed the 3 screws that held the element in place. My husband disconnected the back wired part of element .Then he reconnected new element wires and I rescrewed 3 screws in of new element. Very simple. I just wasn't sure about the back wired part, but like I said my husband seemed to know what he was doing so I let him do that part
... Read more
!
Read less
Was this helpful?
Thank you for voting!
Stove-top Burner intermittently shut off and on-wouldn't heat properly
3 of 3 people
found this instruction helpful.
-
George from New Bloomfield, PA
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
removed old Plug-in block by removing 1 screw and cutting 2 wires. (Screw was so tight and rusty that I had to use vise grips to remove it). Installed new Plug-in block with wire nuts and heat shrink wraps. YOU just have to make sure the wires are seated in the block properly. This job was much easier than I anticipated. The burner works
... Read more
great now!
Read less
Was this helpful?
Thank you for voting!
Burned out bake element
4 of 6 people
found this instruction helpful.
-
Gregory from Norfolk, VA
- Easy
- 15 - 30 mins
-
Screw drivers
Went together real easy , but I poped a fuse/circuit braker.
The braker would not reset at first, but we got it all working fine.
The braker would not reset at first, but we got it all working fine.
Was this helpful?
Thank you for voting!
Blowing Breaker
3 of 4 people
found this instruction helpful.
-
Jason from Wrentham, MA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed screws holding rear cover, removed cover. Male connector on Broil Element had rusted off and caused wire to fall onto the frame of the range, shorting it out.
Removed element by disconnecting other wire and removing the single Phillips head screw accessible from inside the oven. Released the element from the two hook ... Read more s towards the front of the oven near the door and removed.
The wire to the element that burned off had a high temperature female push on connector that I did not have on hand. I had a high temp ring connector so I drilled one of the male connectors on the new element so I could use a small stainless screw and nut which I had to hold the ring terminal on.
After crimping the new connector on I fastened it to the element, connected the other wire and put the rear cover back.
Good to go now!
Removed element by disconnecting other wire and removing the single Phillips head screw accessible from inside the oven. Released the element from the two hook ... Read more s towards the front of the oven near the door and removed.
The wire to the element that burned off had a high temperature female push on connector that I did not have on hand. I had a high temp ring connector so I drilled one of the male connectors on the new element so I could use a small stainless screw and nut which I had to hold the ring terminal on.
After crimping the new connector on I fastened it to the element, connected the other wire and put the rear cover back.
Good to go now!
Read less
Was this helpful?
Thank you for voting!
i sat a tupperware bowl on a hot burner and it stuck to the burner so i had to replace it
3 of 4 people
found this instruction helpful.
-
judy from palatine, IL
- Really Easy
- 15 - 30 mins
just plugged it in!
Was this helpful?
Thank you for voting!