EJS306 Caloric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Element had burned out
1 of 2 people
found this instruction helpful.
-
Judith from Star, ID
- Really Easy
- Less than 15 mins
Package arrived while I was working at the computer and my husband announced minutes later, "That's what I like to see". I didn't know what he was talking about until he tossed the packing list on my desk and said, "It works perfectly. Good Job!" It had only taken a minute to pop the new parts in and he already had water on for coffee.
Other Parts Used:
Was this helpful?
Thank you for voting!
Simple - needed to replace the drip pans on the stove between tenants in a rental apartment
1 of 2 people
found this instruction helpful.
-
Tama from Pacific Grove, CA
- Really Easy
- Less than 15 mins
This wasn't much of a repair -- rather a replacement of a simple abused part. At the same time, PartSelect allowed me to order what I needed after two failed attempts to buy replacements that would fit the range. I'll remember PartSelect if we need parts for other older appliances in the rental units.
Was this helpful?
Thank you for voting!
Stove Burner wouldn't heat up
1 of 2 people
found this instruction helpful.
-
Donna from Sandwich, MA
- Really Easy
- Less than 15 mins
Someone did the repair for me.
Was this helpful?
Thank you for voting!
broiler pan missing
1 of 2 people
found this instruction helpful.
-
RAYMOND from JACKSONVILLE, FL
- Really Easy
- Less than 15 mins
ordered new broiler pan
Was this helpful?
Thank you for voting!
Drip pans were old and with burnt on food that I couldn't get off. Disgusting!!
1 of 2 people
found this instruction helpful.
-
Nicki from ELSIE, NE
- Very Easy
- Less than 15 mins
No problem Took off old ones and replaced with new.
Was this helpful?
Thank you for voting!
Drip pans needed to be replaced
1 of 2 people
found this instruction helpful.
-
Mark from ROSENBERG, TX
- Very Easy
- Less than 15 mins
1) removed heating elements. 2) removed drip pans. 3) installed new drip pans. 4) reinstalled heating elements
Other Parts Used:
Was this helpful?
Thank you for voting!
Large burner on stove not working
1 of 2 people
found this instruction helpful.
-
Cherie from Dowagiac, MI
- Really Easy
- Less than 15 mins
I removed the heating element and noticed that the prongs were corroded. I looked for a model number but couldn't find it so it made it difficult to find a replacement until I got on this website. I found the replacement part and also found that as I checked for other sites for this part this company was the most resonable priced.
T ... Read more he part arrived and I replaced it in seconds. Turned it on and it worked immediately. Super easy.
T ... Read more he part arrived and I replaced it in seconds. Turned it on and it worked immediately. Super easy.
Read less
Was this helpful?
Thank you for voting!
My drip pans were in bad shape
2 of 5 people
found this instruction helpful.
-
Sandra from Oldsmar, FL
- Really Easy
- Less than 15 mins
I removed the old and repaced with new. I never ordered anything one day and got it the next. I'm impressed
Other Parts Used:
Was this helpful?
Thank you for voting!
Had 2 bad cooking elements and needed 4 new pans for the burners
1 of 3 people
found this instruction helpful.
-
Miles from Apache Junction, AZ
- Really Easy
- Less than 15 mins
Ordered the parts and when I received them I simply removed the old ones and replaced them with the new ones. No tools were required.
Other Parts Used:
Was this helpful?
Thank you for voting!
2 of the burners were not working arching and smoking
1 of 3 people
found this instruction helpful.
-
Tina from Laurel, MT
- Really Easy
- 15 - 30 mins
-
Screw drivers
Time was do to the fact that I replaced two elements! I turned off the power to the braker box, unplugged the stove and removed the screw holding the element plug in, removed the part, and cut the wires where they were clean looking (not damaged by smoke or the arch) I then stripped the wire and took the new part and twisted the parts t
... Read more
ogether with the caps and then put the heat shrink on and used the blow dryer on them, attached the part to the bracket and screwed it to the hood of the stove plugged the burner in, plugged in the oven and turned on the power tested it worked, did the same for the next burner and yes mind you I am a woman it was very easy to do.
Read less
Was this helpful?
Thank you for voting!
burned oven bulb
3 of 9 people
found this instruction helpful.
-
Ivanka from Atlantra, GA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new ligh
... Read more
t bulb in was not the problem.
Read less
Was this helpful?
Thank you for voting!
cooking element shorted out and did not heat.
0 of 1 people
found this instruction helpful.
-
Carolyn from Fyffe, AL
- Really Easy
- 30 - 60 mins
-
Screw drivers
I had bought the 1st set of plug-in blocks at lowes, They were the only type they had the univeral ones! They did not hold the elements plug tight enough and half the time they would have to be punshed in more then they would snap and sizzle- I ordere the newer style and they have done great they are better made and heavier metal parts-
... Read more
they elements fit in snuggly and do not sizzle or nor do I have to push the element in. This stove is 35 years old and I have replaced most everything on it. But it's still cooking...
Read less
Was this helpful?
Thank you for voting!
contacts in plug-in block badly burned & oxidized
0 of 1 people
found this instruction helpful.
-
william from port st lucie, FL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
First I removed the one screw that held the element in place. I then pulled the element out about 3 inches and cut the two wires...)
Assembled the block parts.
Installed shrink sleve and applied wire nuts to electrical connection to 2 wires then shrunk the sleve.
Did the above procedure for 2 heating elements.
They w ... Read more ork very well now.
Assembled the block parts.
Installed shrink sleve and applied wire nuts to electrical connection to 2 wires then shrunk the sleve.
Did the above procedure for 2 heating elements.
They w ... Read more ork very well now.
Read less
Was this helpful?
Thank you for voting!
burner connector - bad connection
0 of 1 people
found this instruction helpful.
-
Terry from Grand Forks, ND
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed burner and tray. Removed burner connector from stove top using screw driver.
Removed existing heat shrink and wirenuts.
Installed new connector - wire nuts and heat shrink. Used lighter to shrink.
Took 20 minutes.
Removed existing heat shrink and wirenuts.
Installed new connector - wire nuts and heat shrink. Used lighter to shrink.
Took 20 minutes.
Was this helpful?
Thank you for voting!
burner wouldn`t stay hot.
0 of 1 people
found this instruction helpful.
-
Cary from Gilbertsville, PA
- Easy
- 15 - 30 mins
-
Screw drivers
First I lifted the cooktop out of the countertop & removed the screws so I could access under the burners.Then I cut the wires for the old plug-in block & then stripped the wires.Next I connected the new wires with the wire nuts & then used a lighter to shrink wrap the wire nuts.Then I screwed in the new block & re-installed the screws fo
... Read more
r the cooktop.I put in the new burner & it worked just like new.
Read less
Was this helpful?
Thank you for voting!