EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

EJS306 Caloric Range - Instructions

All Instructions for the EJS306
76 - 90 of 140

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven light burnt out
3 of 10 people found this instruction helpful.
  • William from Schwenksville, PA
  • Easy
  • Less than 15 mins
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Was this helpful?
Thank you for voting!
contacts had gotten burnt out/blackened with age so burner was intermittent.
0 of 1 people found this instruction helpful.
  • john from reading, MA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
lifted the cover, unscrewed the ceramic wire fastners, put the new part in, and voila, job done and working perfectly
Was this helpful?
Thank you for voting!
Old surface element burned out.
0 of 2 people found this instruction helpful.
  • Royce from Rio Rancho, NM
  • Really Easy
  • Less than 15 mins
I ordered and received the replacement element, then unplugged the old one and plugged in the new one.

Job done.
Was this helpful?
Thank you for voting!
large burners not working
0 of 2 people found this instruction helpful.
  • Greg from Versailles, IN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Read instuctions first Turn breaker off to stove or unplug to be sure. Remove burner and drip pans. Remove scews holding socket in place if you are doing more than one make sure you keep in same location. Raise cook top untill supports latch in. Assemble plug it comes with two types holder compare to your plug. cut wire to old plug so yo u have enough wire to connect back with new. Strip wire back and place shrink tubeover wires wire nut together heat with a lighter or heat gun then do remaining plugges. place back in cover and replace scews. make sure wire are not to long to get under burner when cook top lowered. Lower cook top and clean burner plug ends with a little sandpaper to make sure they make good connection. replace pans and burner. turn on breaker or plug in stove making sure the burners come on when turned on good luck g.d.
Was this helpful?
Thank you for voting!
Bulb Replacement
0 of 2 people found this instruction helpful.
  • Judith from Phoenix, AZ
  • Really Easy
  • Less than 15 mins
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this helpful?
Thank you for voting!
replace burner coil connector
0 of 2 people found this instruction helpful.
  • dicky from mcrae, AR
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be su re and disconnect power before starting!!
Was this helpful?
Thank you for voting!
Burners quit working
  • Brenda from Brazoria, TX
  • Really Easy
  • Less than 15 mins
Bought two new replacement burners,they work great!
Was this helpful?
Thank you for voting!
burner not working
  • gene from kent, WA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
burner was shorting out replaced part works great
Was this helpful?
Thank you for voting!
burner would not heat up the connection was bad
  • Earl from Union Mills, NC
  • Really Easy
  • Less than 15 mins
  • Screw drivers
loosened the screw holding the block pulled it out toget to wire cut it about 4 inches long followed the inst.with block kit and it was a breeze. burner working fine now should have did it sooner.
Was this helpful?
Thank you for voting!
Light bulb failure
  • Grant from Alexandria, VA
  • Really Easy
  • Less than 15 mins
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this helpful?
Thank you for voting!
Surface burner block corroded
  • Teresa from Kasson, MN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
It was a very easy fix. I followed the instructions that came with the kit and cut the original cable. Everything you need is in the kit; very few parts. Piece of cake and saved a lot of money an appliance repair person would have charged. This burner works better than the rest. I'm seriously considering replacing the other three blocks.
Was this helpful?
Thank you for voting!
Blocks were broken
  • James J from Sweet Grass, MT
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
The four kits arrived, use of a pliers and shink wrap and side cutters...strip wires, twist wires connect wire ties, shrink wrap...little fire, plug the elements...done...four in about ten minutes...Instructions in each package...no problem...very easy...saved twice the money or more...Thanks for the parts...recommend this site purchase.. .parts arrived very timely...J. Iriwn
Was this helpful?
Thank you for voting!
circuit breaker blew
  • Richard from Sarasota, FL
  • Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in abo ut 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.
Was this helpful?
Thank you for voting!
needed a new drip bowl and couldn't find ons that fit exactly but you had it
  • Elsie from Garner, NC
  • Really Easy
  • Less than 15 mins
I removed the old one and put in the new one. Works great!!!!!!!!!!!!
Was this helpful?
Thank you for voting!
To Old Needed To Be Replace
  • ROSARIO from MESQUITE, TX
  • Really Easy
  • Less than 15 mins
Actualy I just removed the old ones and replace them with the new ones . And thank you for your prompt delivery I found some one I can trust . Thanks again . Mrs bolanos
Was this helpful?
Thank you for voting!
All Instructions for the EJS306
76 - 90 of 140