EJS306 Caloric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
burner would not heat.
1 person
found this instruction helpful.
-
Jackie from Hughes Springs, TX
- Really Easy
- Less than 15 mins
I unpluged the old burner and pluged the new one in. Repair done in about 2 min,
Was this helpful?
Thank you for voting!
The dryer tumbler belt broke
1 person
found this instruction helpful.
-
John from Dillingham, AK
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I opened the dryer by lifting the top and propping it open. I unscrewed two screws on either side with a flat-blade screwdriver, unclipped the dryer stop door micro switch. I slid the new belt over the drum to the center, then used the flashlight to see where it went. There is a tension wheel that had to be pulled to the right and with t
... Read more
he belt in place release against the belt to apply constant pressure during operation. I vacuumed the dryer out and put it back together
Read less
Was this helpful?
Thank you for voting!
ELECTRIC BURNER SUPPORT FELL OFF AND BURNER SOMETIMES WOULD NOT COME ON.
1 person
found this instruction helpful.
-
RICHARD from SHOW LOW, AZ
- Very Easy
- Less than 15 mins
Stuck the new one into the plugin.
Was this helpful?
Thank you for voting!
Oven element broken
1 person
found this instruction helpful.
-
Louise from BROOKFIELD, IL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Unscrewed element connection and replaced with new one! Better than buying a new stove??thank you! We did turned off the circuit breaker!!
Was this helpful?
Thank you for voting!
N/A
1 person
found this instruction helpful.
-
Gerry from Mackay, ID
- Really Easy
- 15 - 30 mins
-
Screw drivers
I followed the instructions provided.
Was this helpful?
Thank you for voting!
Drip Pans were stained and burned on.
1 person
found this instruction helpful.
-
Sandra Collignon from SANTA CLAUS, IN
- Really Easy
- 30 - 60 mins
Replaced drip pan. Notch did not want to match the burner notch. Was a close fit bit with a little pressure made it work.
Was this helpful?
Thank you for voting!
Three of four electric coils won't turn on
1 of 2 people
found this instruction helpful.
-
Arsenio from Beaverton, OR
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I took out the coils manually by pulling them out with slight pressure. Then I lift the hood by first unscrewing the four screws. I have never done anything like this before just intuitive sense to locate the screws that needed to be loosened. Afterwards I remember placing something underneath like a piece of 2x4 wood block to act as supp
... Read more
ort to hold the hood open so I can work on the coils. The parts I got are exactly the same as those I am replacing so I just copied the connection and voila my electric range is working like new. Well of course before I touched anything, I made sure I turned off the main switch and that nobody switches it back on without my knowledge. Thanks for providing the parts, I just saved myself from buying a $600 electric range.
Read less
Was this helpful?
Thank you for voting!
I snapped a bolt on the main power terminal block when connecting the pigtail.
3 of 8 people
found this instruction helpful.
-
Frank from Palm Coast, FL
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver.
... Read more
Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.
Read less
Was this helpful?
Thank you for voting!
Sockets burnt out.
1 of 2 people
found this instruction helpful.
-
James from Bear, DE
- Really Easy
- 15 - 30 mins
-
Screw drivers
Repair was very east. The suppliers package had all of the necessary parts ceramic wire nuts wire Ect. Excellent.
Will buy from Part Select Appliance again.
Will buy from Part Select Appliance again.
Was this helpful?
Thank you for voting!
The Problem Was That The Plug Was Gone It Fell Down Out Of The Bracket
1 of 2 people
found this instruction helpful.
-
Elnora from Brundidge, AL
- Easy
- 15 - 30 mins
-
Screw drivers
I took the old wires and plug off and replaced it with the new block it works fine
Was this helpful?
Thank you for voting!
wire came loose and shorted out
1 of 2 people
found this instruction helpful.
-
Elizabeth from HOUSTON, TX
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.
Was this helpful?
Thank you for voting!
Just needed new drip pans for burners
1 of 2 people
found this instruction helpful.
-
Ann from Cadiz, KY
- Really Easy
- Less than 15 mins
Was glad to get the correct ones for a 30 year old stove. Had already wasted $12 shipping trying to order from someone else.
Other Parts Used:
Was this helpful?
Thank you for voting!
Burner ceramic disintegrated & spalled
1 of 2 people
found this instruction helpful.
-
Gary L from North Tonawanda, NY
- Really Easy
- Less than 15 mins
Pulled buner element out of socket as you would for detailed cleaning. Replaced burner element & drip pan with OEM parts. Fit was perfect, tested burner on all heat ranges, good as new.
Was this helpful?
Thank you for voting!
Drip bowls very dirty and stained
1 of 2 people
found this instruction helpful.
-
john from donna, TX
- Really Easy
- Less than 15 mins
Remove burner elements. Remove old drip pans. Thoroughly clean stove top under drip pan edges, and under top cover. Install new drip pans. Install burner elements.
I never seem to be able to find the correct replacement drip pans at retail outlets in the quantities I need. Your parts identification, selection and ordering proces ... Read more ses were simple and delivery was faster than I hed expected.
Thank you
I never seem to be able to find the correct replacement drip pans at retail outlets in the quantities I need. Your parts identification, selection and ordering proces ... Read more ses were simple and delivery was faster than I hed expected.
Thank you
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Old burner pan warped.burner sat at 15 degree angle.
1 of 2 people
found this instruction helpful.
-
Michael from Portland, OR
- Really Easy
- Less than 15 mins
Removed burner and then burner pan.Then replaced pan and reinstalled burner.
Was this helpful?
Thank you for voting!