EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

CW20P8AC Crosley Washer - Instructions

All Instructions for the CW20P8AC
106 - 120 of 264

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer Walking Across Floor,From Being Off Balance
0 of 1 people found this instruction helpful.
  • Kenneth from Griffith, IN
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
1- Unplug unit 2-disconnect water hoses 3-put unit in open area so you can work on it. 4-Open top cover with screw driver 5-take off front cover with appropriate socket 6-lay unit on it back to get access to the drive belt (take off). And take off water hose with plyers. 7-With vise grips take off the six springs. 8-Take tub assy ou t,and lay it on the floor upside down. 9-Loosen the screws to take out the old snubber ring, note ( when lossening screws,keep your finger on the bottom of the screw ,so you can feel how far to back the screws out,just enough to have access to the snubber ring,to take out,and install new one. )Remember not to take screws out completely. The unit is under spring tension. 10-Put washer back together in reverse order,and problem solved!
Was this helpful?
Thank you for voting!
drive pulley broke off from drain pump
0 of 1 people found this instruction helpful.
  • John from Pomfret, MD
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Raised washer. Identified problem. Removed from panel, gaining access to drain pump. Removed hoses, replaced pump. NOTE: I used blue Loctite on pump mounting bolts. Reinstalled from panel, lowered washer, cleaned drum. Ran one (1) cycle with hot water and bleach ONLY.
Was this helpful?
Thank you for voting!
Washer going out of balance
0 of 1 people found this instruction helpful.
  • Brian from Rock Hill, SC
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Tilted washer back and removed belt
Lifted front of top and propped up
Unscrewed two screws and removed front of washer
Disconnected two drain lines from tub
Disconnected 6 springs from tub
Removed tub
Popped off bottom plastic cap
Removed locking ring
Slid off gear from shaft
Unbolted screws f rom snubber support ring
replaced snubber
Put everything back together in reverse order

Worked like a champ!!!!!
Was this helpful?
Thank you for voting!
Pulley Bearings Siezed; Pump Quit
0 of 1 people found this instruction helpful.
  • Robert from Columbia, MO
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
Turned it over to my 35-year old son who removed pump and pulley assembly and the old drive belt, then simply replaced with new assembly and belt from PartSelect! Could not have been easier - from my viewpoint.
Was this helpful?
Thank you for voting!
Needed to replace the water pump
0 of 1 people found this instruction helpful.
  • Theresa from Zanesville, OH
  • Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Wrench set
The Clamps for the hoses were difficult to get to, otherwise was a simple replacement job, involving clamps and screws and bolts.
Was this helpful?
Thank you for voting!
Bearings in mechanical pump seized.
0 of 1 people found this instruction helpful.
  • Scott from Idaho Falls, ID
  • Easy
  • Less than 15 mins
  • Pliers, Socket set
Unbolt old pump with three bolt from top of pump inside the washer. Use needlenose pliers to remove intake and output hoses from old pump. Remove belt from pulley under washer. Reverse procedure to install. I was worried because there were two pumps listed for this model number, one being $95 and the other being $40. I bought the cheaper one and prayed. It worked just fine. Fixed a $500 washer that was on it's way to the dump and made $100 in the process!
Was this helpful?
Thank you for voting!
Washing machine had difficulty in spine cycle
0 of 1 people found this instruction helpful.
  • Stephanie from Ticonderoga, NY
  • Really Easy
  • Less than 15 mins
Unplugged everything, disconnected hoses, took belt off and put new one on.
Was this helpful?
Thank you for voting!
worn drive belt
0 of 1 people found this instruction helpful.
  • James from Shortsville, NY
  • Really Easy
  • Less than 15 mins
tilted the machine forward, worked off the old belt and put the new belt back on. no tools required, done in less than 5 minutes.
Was this helpful?
Thank you for voting!
Washer Machine just shut down.
0 of 1 people found this instruction helpful.
  • Patrick from Indianola, MS
  • Really Easy
  • Less than 15 mins
All i had to do was pull the washer machine from the wall and lean it back as far as i could and get under it and place the (DRIVE BELT) on the two smallest pulley then put the belt on the large pulley and my work was done it was very simple and easy.......
Was this helpful?
Thank you for voting!
Made an awful sqealing noise and did not spin the water out all the way
0 of 1 people found this instruction helpful.
  • Deborah from Baltimore, MD
  • Really Easy
  • Less than 15 mins
  • Socket set
Leaned the washer back and propped it up and changed the belt. This is the first time ever repairing an appliance. I feel very good about myself as I am 49 yrs old and did not have to call a repairman for this.
Was this helpful?
Thank you for voting!
Washer would not go into spin cycle.
0 of 1 people found this instruction helpful.
  • Jack from Scottdale, PA
  • Really Easy
  • Less than 15 mins
I pulled the washer away from the wall so that I could lean it back at an angle. I removed the old belt and put the new one on. I started with the smaller pulley first and put the belt into the groove. Next I went to the next larger pulley and did the same thing. Then I went to the largest pulley and started to put the belt into the groov e and started turning the pulley by hand. The belt went right on.
Was this helpful?
Thank you for voting!
washing machine filled with water, nothing else happened.
0 of 1 people found this instruction helpful.
  • Ellie from Eastview, KY
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Spoke with a trusted repair man, described the problem best as I could. I smelled a burning rubber smell. Got on Internet for troubleshooting problems, 77% likely a drive belt. BINGO! Ordered a new belt, took old one off, cleaned the pulley ( it had burnt rubber stuck on it, difficult to remove) lightly sanded pulley just so it would be r eally smooth. replaced belt. Magic, it worked. I am no repair woman, but carefully listening and explaining helped. Oh, belt is under the very bottom of machine. Very easy to get to, just tilt back and lodge at an angle and make sure it doesn't move.
Was this helpful?
Thank you for voting!
loud sqeaking noise, burnt rubber smell, motor siezing up
0 of 1 people found this instruction helpful.
  • Ricky from Colorado Springs, CO
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Unplugged electrical plug. Disconnected water and drain hoses. Turned washer on front side. Removed old belt from bottom of washer. Removed pump access panel. Removed old pump. Installed new pump. Torqued pump mounting screws 1/4 turn with socket wrench. Installed new belt. Put on pump access panel. Hand tested motion of belt and pulleys for smooth travel. Put drain hose on. Turned washer in the upright position. Reconnected water hoses. Washer works like new.
Was this helpful?
Thank you for voting!
loud noise while washing, spinning and draining
0 of 1 people found this instruction helpful.
  • Julia from Columbia, IL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
took off back small metal panel, tilted washer front side down, easy to put into place after removing old part
Was this helpful?
Thank you for voting!
Squealing Belt In All Cycles
0 of 1 people found this instruction helpful.
  • TERRY E from TUCSON, AZ
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
Because I live alone, the washer is very heavy so I just used some sliding robots under the legs of washer so I could slide it out from the wall by myslef after removing the small plate in the back to accfess the water pump I used the nut driver to remove the 3 screws holding the pump in place, but I used the pliers to remove the 2 water hoses first then I mounted the water pump back into place, installed both hoses again then I tilted it back against the wall while re installing the belt then I pushed it back against the wall and removed the sliders so I could make sure it was back level this was a very easy repair even if you never fixed any thing before the belt replacement was even more simple to replace because the motor is springloaded so you just had to pull on it enough to remove it from the pulleys
Was this helpful?
Thank you for voting!
All Instructions for the CW20P8AC
106 - 120 of 264