CW20P8AC Crosley Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water removal pump stopped working.
1 person
found this instruction helpful.
-
Timothy from Palmdale, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Removed lower rear panel by removing 8 screws. Then I removed the two hoses that are attached to the pump by removing the hose clamps with a pair of plyers. The three hex head screws that anchor the pump to the base of the washer unit were removed and the pump came right out. To put the new pump in I just slipped the pump through the hol
... Read more
e at the bottom of the washer and attached the belt onto the pulley. Then reversed the installation process. The washer had to be tipped forward slightly for this process and blocked (approx. 8 in.) to allow access to pulley. Very easy install, no help needed. Washer must be empty and preferable dry when task is done or water will be everywhere.
Read less
Was this helpful?
Thank you for voting!
Water leak
2 of 4 people
found this instruction helpful.
-
Joe from Clearfield, PA
- Really Easy
- 15 - 30 mins
-
Socket set
Removed front cover, identified leak, ordered part, saved over half of the cost on part, no service call fee. I feel great!
Was this helpful?
Thank you for voting!
Washer made horrible noise when entering the spin cycle.
1 person
found this instruction helpful.
-
Lance D. from Broken Arrow, OK
- Easy
- Less than 15 mins
-
Nutdriver, Pliers, Socket set
I removed the cover on the back of the machine, detatched the 2 hoses and removed the 3 screws holding in the Vertical Style Pump - with pulley. These screws are 10 mm nut-driver. The cover if I remember correctly was a standard rather than metric so make sure you have both available.
Screwed new part in, re-attached hoses an ... Read more d replaced cover. The last step requires strength to hold the machine up and re-configure the belt. This is best accomplished by looping it onto the tub and the pump first, the using the tub pulley to maneuver the belt onto the motor.
Only discouragement was that it took 8 days to receive the part as the first shipment was not the correct part at the fault of the distrutor.
Screwed new part in, re-attached hoses an ... Read more d replaced cover. The last step requires strength to hold the machine up and re-configure the belt. This is best accomplished by looping it onto the tub and the pump first, the using the tub pulley to maneuver the belt onto the motor.
Only discouragement was that it took 8 days to receive the part as the first shipment was not the correct part at the fault of the distrutor.
Read less
Was this helpful?
Thank you for voting!
pump bering failure
1 person
found this instruction helpful.
-
Robert from Englewood, FL
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
first i removed the front panel unclamped the hoses unscrewed the 3 screws that hold it in pulled it out, opened the new one and actually dropped it in and it fell into place with the holes lining up inserted the screws and hose clamps and reinstalled the belt which fell off when the old pump was removed, put the front back on and gave it
... Read more
a test then let the wife do a load of wash it worked like new
Read less
Was this helpful?
Thank you for voting!
water leaking from under front of washer
1 person
found this instruction helpful.
-
Mark from Isom, KY
- Really Easy
- Less than 15 mins
after doing some research I found out that a loose or slipping water pump belt could cause the water pump to not pump out the water correctly. Under the washer is the belt. All you do is have someone lift the front of the washer up enough that you can reach under and remove the belt. Then replace the belt back like you took it off.
Was this helpful?
Thank you for voting!
would not engage spin cycle, belt was shredding.
1 person
found this instruction helpful.
-
john from mashpee, MA
- Really Easy
- Less than 15 mins
pulled the machine out, tilted it backward to expose the bottom. pulled off the old belt. got the new belt started on the three pulleys. pulled the belt to spin it , and...............done !!
Was this helpful?
Thank you for voting!
Had a squeaky belt
1 person
found this instruction helpful.
-
Michael from Mokena, IL
- Really Easy
- Less than 15 mins
Piece of cake. Raise up the front of the machine. the belt slips of easy by turning the main drive wheel. put the belt on the two small one and then rotate the big wheel as you slip the belt into the grove. good idea to first clean the wheels of any old belt material that may be worn off. Piece of cake!
Was this helpful?
Thank you for voting!
Broken belt needed to be replaced.
1 person
found this instruction helpful.
-
Niels from Hopewell Junction, NY
- Easy
- Less than 15 mins
-
Socket set, Wrench (Adjustable)
Replacing a belt on a washing machine is a pretty easy process, depending slightly on how easy it is to access the belt. On our Maytag, the belt can be accessed directly underneith the washing machine. So, I lifted the front of the machine and put a few blocks of scrap wood under the legs to hold up the front of the machine. Once that
... Read more
was done, there was nothing else that needed to be removed to access the pullies that the belt had to go around. The motor itself is generally adjustable to allow the belt to be changed. So, I first wrapped the belt around the largest one that spins the washin machine tub, and then wrapped it around the one that spins the water pump. Finally, I loosened the bolt on the motor to allow it to move, wrapped the belt around the motor, pulled the motor back to tighten up the belt, and tightened the bolt that holds the motor in place. It's a pretty straight forward repair that narly anyone could do thmselves.
Read less
Was this helpful?
Thank you for voting!
Locked up the machine.
1 person
found this instruction helpful.
-
Mitchell B. from Moreno Valley, CA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers, Socket set
Unhooked the macine pulled out for easy access .removed drive belt rear cover plate ,vaccumed remaining water out thru drain hose with wet and dry vac. Removed hose clamps and hoses .removed the three hex screws holding the pump to the base plate. The removed the old pump , Installed the new pump hoses access plate and belt . Hooked the
... Read more
machine up . Worked perfect.
the
the
Read less
Was this helpful?
Thank you for voting!
Wore out Pulley/Bearing
1 person
found this instruction helpful.
-
Mark from Akron, CO
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
Disconnect all water supply and unplug washer. Remove 3 screws on back panel of the washer. This will expose the pump unit. Detach belt on the bottom of the washer. Then detach two hoses that connects to the pump unit. Use pliers if necessary to disconnect hoses. Use 5/16 socket with extension to take out three bolts the connect pump to t
... Read more
he washer. That's it, now replace old pump unit and with new. Place bolts back in the 3 holes, reattached hoses, cover the back with 3 scres. Connect the belt to the pulley system on the bottom. Connect water supply and plug it in.
Read less
Was this helpful?
Thank you for voting!
Machine was wailing like a stuck pig!
1 person
found this instruction helpful.
-
Jeff from Sugar Land, TX
- Really Easy
- Less than 15 mins
Pulled that sucker out from the wall and leaned him back just enough to prop a case a beer under it. Slid up under there with the biggest dust bunny I ever seen. Yanked that old belt off and threw it away. Tried to uncoil the new one and it slapped me in the nose! Got it uncoiled and around the two smaller pulleys pulling the adjustable o
... Read more
ne in to it's limit and walked the belt around the big drum pulley. By the time my wife put down her coffee and came to see if she can lend me a hand I was done!.
Read less
Was this helpful?
Thank you for voting!
Made noise on spin cycle
1 of 2 people
found this instruction helpful.
-
Les from Moneta, VA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Took off belt and ran motor. No noise. Then took off drain pump and spun it by hand and felt rubbing on one spot. I figured the bearings were going bad, so I ordered the parts and replaced them.
Other Parts Used:
Was this helpful?
Thank you for voting!
machine was starting to make noises when spinning
1 of 2 people
found this instruction helpful.
-
Virginia from Rockford, IL
- Really Easy
- Less than 15 mins
My husband unhooked the water lines, unplugged the washer and remove the waste water hose, then we tipped it over and easy as pie the belt came off and the new one went right back on. I did not see any tears or breaks in the old belt, but it was stretched out a bit, and the washer is once again quiet. This also gave me an opportunity to
... Read more
clean under the washer, which we all know we don't do unless we have to. Cheap, quick, and easy fix for someone to do there self.
Read less
Was this helpful?
Thank you for voting!
Water pump replacement
1 of 2 people
found this instruction helpful.
-
Lon from Morton Grove, IL
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Pliers, Socket set
Reverse the process to install new pump
Unplug the machine
Place pad on floor to protect the machine from scratches
Lay front of machine on floor
Remove back cover (10 screws)
Disconnect 2 hoses
Remove 4 screws which secure pump to bottom frame
Remove belt
Remove pump
Reverse the process ... Read more to install a new pump
Your web sites intuitive design makes it easy to navigate and the customer service person was knowledgeable, easy to understand and professional.
The part arrived via UPS in 3 days. It was double boxed (well packaged) and most importantly, it was the correct part.
This was is 1st time we used your server but it won’t be the last!
Kudos to the entire staff and please…keep up the good work.
Sincerely,
Lon Thomas
Unplug the machine
Place pad on floor to protect the machine from scratches
Lay front of machine on floor
Remove back cover (10 screws)
Disconnect 2 hoses
Remove 4 screws which secure pump to bottom frame
Remove belt
Remove pump
Reverse the process ... Read more to install a new pump
Your web sites intuitive design makes it easy to navigate and the customer service person was knowledgeable, easy to understand and professional.
The part arrived via UPS in 3 days. It was double boxed (well packaged) and most importantly, it was the correct part.
This was is 1st time we used your server but it won’t be the last!
Kudos to the entire staff and please…keep up the good work.
Sincerely,
Lon Thomas
Read less
Was this helpful?
Thank you for voting!
Made noise during washing and rinse cycle
1 of 2 people
found this instruction helpful.
-
Jose from Elizabeth, NJ
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
It was easy to replace the water pump
Other Parts Used:
Was this helpful?
Thank you for voting!