CW18P2WC Crosley Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer was leaking water.
1 of 3 people
found this instruction helpful.
-
Steven from Atlanta, GA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Socket set, Wrench (Adjustable)
Removed front of washer following instructions on partselect.com (used putty knife to release catches). Removed hoses and belt from pump, then removed and replaced the pump. Reattaching the belt was the only awkward task.
Was this helpful?
Thank you for voting!
Pump was making a grinding noise.
1 of 3 people
found this instruction helpful.
-
Daniel from Hinsdale, IL
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
I tilted the machine on it's back to remove the drive belt. You could feel the friction in the pump when you turned the pulley. I set the machine back down and removed the back cover (4 screws). I removed the two hoses with a pair of pliers. I used a small socket set to remove the three mounting screws. I ordered the pump. I
... Read more
reversed the process to put it back together. It took about 35 minutes to determine what the problem was and to remove the pump. It took about 20 minutes to put it back together.
Read less
Was this helpful?
Thank you for voting!
Noisy Pump
2 of 7 people
found this instruction helpful.
-
Frederick from Yuma, AZ
- Really Easy
- 15 - 30 mins
-
Nutdriver
I placed the washer on a couple of work-horses so I could have access to the belt underneath. Then I used my nutdriver to removed the lower back panel. Disconnected both of the hoses, and removed the pump with my nutdrivers. Placed the new pump in place, placed the belt back on the pump's pully, tightened down the pump. I then plugged
... Read more
in the washer and put a little water in the washer to test that everything was working. After confirming that everything worked, I replaced the lower back panel and put the washer back in business. 30 minutes from beginning to end ... and a good time was had by all.
Read less
Was this helpful?
Thank you for voting!
Bearing on pump making noise and would go out soon.
0 of 1 people
found this instruction helpful.
-
Marcus from Camarillo, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I diagnosed the bearing by putting a 3/4 inch rubber hose up to my ear. I pointed it around until isolating the noise to the pump. The bearing was not servicable without replacing the pump. After diagnosing the problem I ordered the part. Getting the part from PartSelect.com was a snap. It arrived in one day. In 15 minutes I had it back t
... Read more
o gether and working quiet and smooth.
Read less
Was this helpful?
Thank you for voting!
dead pump
1 of 4 people
found this instruction helpful.
-
Andre. M from Glendale, CA
- Really Easy
- 15 - 30 mins
-
Socket set
I first opoen the front panel of the washer. That was a bit tricky. Had to slide a thin blade between the top of the washer and the front panel, pushed in to release the "clamp" and gently raise the top, it hinges on the back.
The rest was undoing three bolts, refit the new pump and put the belt back on.
The part cost me less ... Read more then $65.00.
The repair estimate by the local repair man was $ 250.00.
I am very happy.
Thank you PartSelect.
Andre M. Roberty
The rest was undoing three bolts, refit the new pump and put the belt back on.
The part cost me less ... Read more then $65.00.
The repair estimate by the local repair man was $ 250.00.
I am very happy.
Thank you PartSelect.
Andre M. Roberty
Read less
Was this helpful?
Thank you for voting!
Washer making loud noise when water pump operating, still worked but made very loud noise
0 of 1 people
found this instruction helpful.
-
Buddy from Ogden, UT
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
I ordered the replacement pump assembly (water pump)for my Atlantis model maytag washer, removed the old one, installed the new one and works like a charm. The only difficulty I had was trying to figure out how to remove the cover on the front of the washer, to remove the clips, it slid side to side instead of popping out, found the inst
... Read more
ructions on-line, NO instructions came with the pump but if you have any common sense when it comes to repairs it was easy to remove and install the new part.
Read less
Was this helpful?
Thank you for voting!
washing machine filled with water, nothing else happened.
0 of 1 people
found this instruction helpful.
-
Ellie from Eastview, KY
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Spoke with a trusted repair man, described the problem best as I could. I smelled a burning rubber smell. Got on Internet for troubleshooting problems, 77% likely a drive belt. BINGO! Ordered a new belt, took old one off, cleaned the pulley ( it had burnt rubber stuck on it, difficult to remove) lightly sanded pulley just so it would be r
... Read more
eally smooth. replaced belt. Magic, it worked. I am no repair woman, but carefully listening and explaining helped. Oh, belt is under the very bottom of machine. Very easy to get to, just tilt back and lodge at an angle and make sure it doesn't move.
Read less
Was this helpful?
Thank you for voting!
loud sqeaking noise, burnt rubber smell, motor siezing up
0 of 1 people
found this instruction helpful.
-
Ricky from Colorado Springs, CO
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Unplugged electrical plug. Disconnected water and drain hoses. Turned washer on front side. Removed old belt from bottom of washer. Removed pump access panel. Removed old pump. Installed new pump. Torqued pump mounting screws 1/4 turn with socket wrench. Installed new belt. Put on pump access panel. Hand tested motion of belt and pulleys
... Read more
for smooth travel. Put drain hose on. Turned washer in the upright position. Reconnected water hoses. Washer works like new.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
loud noise while washing, spinning and draining
0 of 1 people
found this instruction helpful.
-
Julia from Columbia, IL
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
took off back small metal panel, tilted washer front side down, easy to put into place after removing old part
Was this helpful?
Thank you for voting!
Squealing Belt In All Cycles
0 of 1 people
found this instruction helpful.
-
TERRY E from TUCSON, AZ
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Because I live alone, the washer is very heavy so I just used some sliding robots under the legs of washer so I could slide it out from the wall by myslef after removing the small plate in the back to accfess the water pump I used the nut driver to remove the 3 screws holding the pump in place, but I used the pliers to remove the 2 water
... Read more
hoses first then I mounted the water pump back into place, installed both hoses again then I tilted it back against the wall while re installing the belt then I pushed it back against the wall and removed the sliders so I could make sure it was back level this was a very easy repair even if you never fixed any thing before the belt replacement was even more simple to replace because the motor is springloaded so you just had to pull on it enough to remove it from the pulleys
Read less
Was this helpful?
Thank you for voting!
noisy pump
0 of 1 people
found this instruction helpful.
-
Tery from Orange, CA
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Removed back plate, tilted up washer removed pump removed belt. Then replace pump and then replaced belt
Other Parts Used:
Was this helpful?
Thank you for voting!
worn drive belt
0 of 1 people
found this instruction helpful.
-
James from Shortsville, NY
- Really Easy
- Less than 15 mins
tilted the machine forward, worked off the old belt and put the new belt back on. no tools required, done in less than 5 minutes.
Was this helpful?
Thank you for voting!
Washer Machine just shut down.
0 of 1 people
found this instruction helpful.
-
Patrick from Indianola, MS
- Really Easy
- Less than 15 mins
All i had to do was pull the washer machine from the wall and lean it back as far as i could and get under it and place the (DRIVE BELT) on the two smallest pulley then put the belt on the large pulley and my work was done it was very simple and easy.......
Was this helpful?
Thank you for voting!
Made an awful sqealing noise and did not spin the water out all the way
0 of 1 people
found this instruction helpful.
-
Deborah from Baltimore, MD
- Really Easy
- Less than 15 mins
-
Socket set
Leaned the washer back and propped it up and changed the belt. This is the first time ever repairing an appliance. I feel very good about myself as I am 49 yrs old and did not have to call a repairman for this.
Was this helpful?
Thank you for voting!
Washer would not go into spin cycle.
0 of 1 people
found this instruction helpful.
-
Jack from Scottdale, PA
- Really Easy
- Less than 15 mins
I pulled the washer away from the wall so that I could lean it back at an angle. I removed the old belt and put the new one on. I started with the smaller pulley first and put the belt into the groove. Next I went to the next larger pulley and did the same thing. Then I went to the largest pulley and started to put the belt into the groov
... Read more
e and started turning the pulley by hand. The belt went right on.
Read less
Was this helpful?
Thank you for voting!