EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

CW18P2WC Crosley Washer - Instructions

All Instructions for the CW18P2WC
121 - 135 of 271

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
drive belt broke
0 of 1 people found this instruction helpful.
  • Gerard from Keansburg, NJ
  • Really Easy
  • Less than 15 mins
pulled out the washing machine that was the hard part, tilted it back checked too make sure everything spun by hand just to see if that was reason for the belt to snap but everything spun by hand nice and smoothly poped on the drive belt and everything works fine back in business.
Was this helpful?
Thank you for voting!
Under belt was used and ready to let go..
0 of 1 people found this instruction helpful.
  • Melanie from Tamarac, FL
  • Really Easy
  • Less than 15 mins
First I am a woman and was able to do it, and if I can do it anyone should be able to do this. The service call alone was 75.00, and the belt was 23.00 with shipping. First we tilted the washer at a 45 degree angle and I removed the belt, and just rolled the newer one on the track. That was it and I was done. My washer now purrs like a ki tten love it. And Part Select sent out my part and I recieved it next day, thank you for wonderful service that kind of service is hard to find. <3
Was this helpful?
Thank you for voting!
Bearings in mechanical pump seized.
0 of 1 people found this instruction helpful.
  • Scott from Idaho Falls, ID
  • Easy
  • Less than 15 mins
  • Pliers, Socket set
Unbolt old pump with three bolt from top of pump inside the washer. Use needlenose pliers to remove intake and output hoses from old pump. Remove belt from pulley under washer. Reverse procedure to install. I was worried because there were two pumps listed for this model number, one being $95 and the other being $40. I bought the cheaper one and prayed. It worked just fine. Fixed a $500 washer that was on it's way to the dump and made $100 in the process!
Was this helpful?
Thank you for voting!
Washing machine had difficulty in spine cycle
0 of 1 people found this instruction helpful.
  • Stephanie from Ticonderoga, NY
  • Really Easy
  • Less than 15 mins
Unplugged everything, disconnected hoses, took belt off and put new one on.
Was this helpful?
Thank you for voting!
Belt was frayed and pump was leaking.
0 of 1 people found this instruction helpful.
  • Glenn from Kansasville, WI
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
I removed the back panel and then removed the old pump. After attaching the new pump I flipped the machine and attached the new belt. I put everything back together and voila, the machine works.
Was this helpful?
Thank you for voting!
Had some difficulty placing pulley back in place
0 of 1 people found this instruction helpful.
  • Oscar from Weslaco, TX
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers, Socket set
Laid washer on its side, released five of the six tub springs, then removed the dive belt and the main pulley. With some effort removing the old snubber ring, placed the new snubber in place. After fighting with the large spring under the pulley I was able to replaced the six screws with the help of an assistant. Replaced the pulley, b elt and the five springs. Closed the unit up and placed all the hoses back in place. I was amazed at how smooth the washer functioned with no vibration at all! Thank You.
Was this helpful?
Thank you for voting!
Washer shook and danced on basement floor
0 of 1 people found this instruction helpful.
  • Bruce H from Mason City, IA
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers, Socket set, Wrench set
I found on-line that replacing the snubber ring may fix the problem and ordered the part. With the instructions also downloaded I started taking the washer apart. Without the instructions the task would have been more difficult and possibly disastrous as I might have taken the bolts out that tighten down the snubber ring. All went well wi th a little patience. The washer works good.
Was this helpful?
Thank you for voting!
when in spin cycle it would shake rattle &roll
0 of 1 people found this instruction helpful.
  • Marvin from Manteca, CA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers
open top,remove back panel.then laid on the side and removed belt.remove hose from tub to pump.removed small hose for fill level.Hard part was to remove springs from tub.Then pull tub and transmission out of housing.Remove pulley from shaft.Lossen screws around snubber ring but do not remove them.Remove old snubber ring.clean surfaces wit h alcohol.install new snubber ring and assemble in reverse order.
Was this helpful?
Thank you for voting!
Water would not drain and tub would not spin.
0 of 1 people found this instruction helpful.
  • Larry from Waukesha, WI
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
I had to raise the top of the washer and take off the front pannel. It was not too hard to replace the pump except that it was in the back corner and it was hard to reach the bolts to remove and install the new pump.
Was this helpful?
Thank you for voting!
washer shaking
0 of 1 people found this instruction helpful.
  • Jerry from Troy, PA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Socket set
took drum out replase snubber put drum back in
Was this helpful?
Thank you for voting!
Washer Walking Across Floor,From Being Off Balance
0 of 1 people found this instruction helpful.
  • Kenneth from Griffith, IN
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
1- Unplug unit 2-disconnect water hoses 3-put unit in open area so you can work on it. 4-Open top cover with screw driver 5-take off front cover with appropriate socket 6-lay unit on it back to get access to the drive belt (take off). And take off water hose with plyers. 7-With vise grips take off the six springs. 8-Take tub assy ou t,and lay it on the floor upside down. 9-Loosen the screws to take out the old snubber ring, note ( when lossening screws,keep your finger on the bottom of the screw ,so you can feel how far to back the screws out,just enough to have access to the snubber ring,to take out,and install new one. )Remember not to take screws out completely. The unit is under spring tension. 10-Put washer back together in reverse order,and problem solved!
Was this helpful?
Thank you for voting!
drive pulley broke off from drain pump
0 of 1 people found this instruction helpful.
  • John from Pomfret, MD
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Raised washer. Identified problem. Removed from panel, gaining access to drain pump. Removed hoses, replaced pump. NOTE: I used blue Loctite on pump mounting bolts. Reinstalled from panel, lowered washer, cleaned drum. Ran one (1) cycle with hot water and bleach ONLY.
Was this helpful?
Thank you for voting!
Washer going out of balance
0 of 1 people found this instruction helpful.
  • Brian from Rock Hill, SC
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Tilted washer back and removed belt
Lifted front of top and propped up
Unscrewed two screws and removed front of washer
Disconnected two drain lines from tub
Disconnected 6 springs from tub
Removed tub
Popped off bottom plastic cap
Removed locking ring
Slid off gear from shaft
Unbolted screws f rom snubber support ring
replaced snubber
Put everything back together in reverse order

Worked like a champ!!!!!
Was this helpful?
Thank you for voting!
Pulley Bearings Siezed; Pump Quit
0 of 1 people found this instruction helpful.
  • Robert from Columbia, MO
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
Turned it over to my 35-year old son who removed pump and pulley assembly and the old drive belt, then simply replaced with new assembly and belt from PartSelect! Could not have been easier - from my viewpoint.
Was this helpful?
Thank you for voting!
Needed to replace the water pump
0 of 1 people found this instruction helpful.
  • Theresa from Zanesville, OH
  • Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Wrench set
The Clamps for the hoses were difficult to get to, otherwise was a simple replacement job, involving clamps and screws and bolts.
Was this helpful?
Thank you for voting!
All Instructions for the CW18P2WC
121 - 135 of 271