CW18P2WC Crosley Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The water pump went out
1 person
found this instruction helpful.
-
felicia from Broken Arrow, OK
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
UNPLUG ELECTRICITY. I pulled out the washing machine turned the water off pulled all of your hoses from the back of the machine there may be a mess so you need some thing that will catch the water as it comes out of the hoses. On the bottom of the machine is a belt you have to remove it. Its easy just pull it off. On the back is a panel t
... Read more
hat you unscrew four screws. On the water pump it self you unscrew three screws. Then for the new part you do in reverse order screw your three screws back in put your hoses back on make sure your clamps are tight around your hoses or you will have a leak. Put your panel back on. Put your belt back on. Turn your water on from the wall plug in the electricity and you are done.
Read less
Was this helpful?
Thank you for voting!
Problem manifested as a loud squealing/grinding noise during all cycles.
1 person
found this instruction helpful.
-
Michael from Atlanta, GA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Disconnected both power and hot and cold input water lines. Laid the washer on its front side for access to the bottom. Removed the small access panel from the back of the machine to remove the metal screws holding the pump in place. Removed the single drive belt. New pump installed easily, replaced the belt and access panel. Reconne
... Read more
cted the power and water hoses and everything worked fine.
Read less
Was this helpful?
Thank you for voting!
Drain pump making load screeching noise
1 person
found this instruction helpful.
-
Danny from Fort Worth, TX
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
I pulled washer out and removed filler hoses from water supply and drain hose and tilted it forward placing three short 2X4's under the washer to keep it tilted forward. Removed
back plate with nutdriver. Removed belt from pulley and disconnected the two hoses from pump with pliers. Removed three large screws from pump base with nut ... Read more driver and removed old pump. Installed the new pump in reverse order. Quick and fairly easy took about 30 minutes.
back plate with nutdriver. Removed belt from pulley and disconnected the two hoses from pump with pliers. Removed three large screws from pump base with nut ... Read more driver and removed old pump. Installed the new pump in reverse order. Quick and fairly easy took about 30 minutes.
Read less
Was this helpful?
Thank you for voting!
pulley was scraping bottom of pump
1 person
found this instruction helpful.
-
Brian from Granbury, TX
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
First , I unlocked top cover and propped; removed front cover. tilted machine back propping front. pump is at lower right corner, removed both hoses, removed belt and three screws. reversed order completing job. You will have some water leakage removing hoses.
Was this helpful?
Thank you for voting!
Water leak
2 of 4 people
found this instruction helpful.
-
Joe from Clearfield, PA
- Really Easy
- 15 - 30 mins
-
Socket set
Removed front cover, identified leak, ordered part, saved over half of the cost on part, no service call fee. I feel great!
Was this helpful?
Thank you for voting!
Loud grinding noise when I ran the washing machine
1 person
found this instruction helpful.
-
Eman from Wood Dale, IL
- Easy
- 30 - 60 mins
-
Pliers, Socket set
It took long because I did not know where the noise is coming from and I took the sides off. I went to the store and bought a new washing machine. Delivery was scheduled in 3 days. I decided to lay the machine on its side and look underneath. I pulled the belt off the 3 pulleys and turned each pulley by hand. The one runing the pump was s
... Read more
tiff and noisey. I ordered the part, arrived in 2 days, installed it in 15 minutes and closed the machine in 30 minutes, then cancelled the order of the new machine and saved $500.00
Read less
Was this helpful?
Thank you for voting!
loud grinding sound then washer would shut down then there was water all over
1 person
found this instruction helpful.
-
marilisa from naples, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Socket set
first removed panel from rear of washer removed hoses and drained water in them, removed the 3 screws and removed the belt then removed the pump. Replaced with new one and put back screws,hoses and belt. walaaa.... it works like new!!!!
Was this helpful?
Thank you for voting!
The water was leaking out from the bottom.
1 person
found this instruction helpful.
-
Doris from Plainsboro, NJ
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
My husband took out the 2 screws in the front panel and loosen the 3 nuts from the pump.
The parts was easily removed and the entire job tooked 30 mins.
The parts was easily removed and the entire job tooked 30 mins.
Was this helpful?
Thank you for voting!
Washer had bad water pump
1 person
found this instruction helpful.
-
Edwin from Eagar,, AZ
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Removed access panel to expose pump, removed drive belt, and old pump, repeated the avove steps in reverse order, tested for leaks and proper operation.
Was this helpful?
Thank you for voting!
Water leaked from bottom of Washing Machine.
1 person
found this instruction helpful.
-
Brandon from Lake Elsinore, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
Removed water lines and drain, removed back panel, removed drain lines from pump. Unscrewed 3 screws to remove pump. attached drain lines to new pump, screwed in new pump, reattached everything. Reinstalled belt (very easy, not like an altenator). done
Was this helpful?
Thank you for voting!
squeel
1 person
found this instruction helpful.
-
william from cypress, TX
- Really Easy
- Less than 15 mins
Tilted machine back, put a paint can under it and did R & R with belts.
Was this helpful?
Thank you for voting!
old belt broke and fell off
2 of 4 people
found this instruction helpful.
-
Tim from New London, OH
- Really Easy
- Less than 15 mins
tipped the washer back, laid on the floor, and wrapped new belt around 3 pulleys. everything works as before.
Was this helpful?
Thank you for voting!
Had the screeching noise for a few days and kept using it until it finally didn't do anything. From youtube i was able to diagnose using other peoples experiences and discovered the part i need by looking at the pictures from the model #.
1 person
found this instruction helpful.
-
Rita from Rodarte, NM
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I had my 12 year old son climb to the back and he took off all the screws necessary in the back and took the part completely off. We ordered the part and waited for it to come in. We replaced the part, the screws and honestly, the only thing we had trouble with was replacing the small cover where the hoses stick out of the washer. Was
... Read more
an easy efficient experience that may have saved me $300.00+ dollars. Thanks to my 12 year old son we got her fixed up. The washer works like brand new.
Read less
Was this helpful?
Thank you for voting!
Activator device broken off
1 person
found this instruction helpful.
-
Sonya from VAIL, AZ
- Very Easy
- Less than 15 mins
-
Screw drivers
Easy repair - with the use of a phillips screwdriver, simply remove the old device and replace with the new
Was this helpful?
Thank you for voting!
Worn belt
1 person
found this instruction helpful.
-
Richard from OXFORD, NY
- Really Easy
- Less than 15 mins
Rolled the old one off and rolled the new one on.
Was this helpful?
Thank you for voting!