EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

CW18P2WC Crosley Washer - Instructions

All Instructions for the CW18P2WC
61 - 75 of 271

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Wouldn't spin after rince
1 person found this instruction helpful.
  • joe from LAWRENCEVILLE, NJ
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Followed the great instructions on your video
Was this helpful?
Thank you for voting!
Spin cycle out of Balance - Machine walks from wall
1 person found this instruction helpful.
  • Needham from Leesville, SC
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
Disconnect Power. Disconnect supply hoses. Open top by releasing top retainer clips with a thin blade or putty knife. Remove 2 sheet metal screws retaining front cover. Remove front cover. Lay a blanket on the floor and lay the machine over on its side leaving access to the front where the panel was just removed. Take belt off. Remove pu mp hose at bottom of drum. Prop up drum so it is centered in its normal position and not laying to one side. Do this near the lid end. Remove all centering springs - carefully. Drum and transmission assy will now come out through the front opening. Flip drum assy upside down with transmission up. Loosen the screws (do not remove completely - WARNING OF 200 LBS SPRING LOAD!) that clamp the snubber ring to the transmission. Remove the old snubber ring and replace with new. Be sure it is completely under the flange all the way around. Tighten the retaining ring screws. Reassemble all parts in reverse order. Done. Be sure to level the machine per owners manual instructions.
Was this helpful?
Thank you for voting!
Washer making noise during cycles
1 person found this instruction helpful.
  • Nat from Baton Rouge, LA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
I moved the washer out from the wall. unplugged washer, turned off water. Took off rear plate exposing pump. Disconnected hoses, using dry/wet vac to catch water. Took out three screws holding pump to base of washer and removed pump, belt slipped right off. Set new pump in place and put in screws. Connected hoses, put rear plate back on. Tilted washer back and installed belt on pulleys and motor. Turned on water, plugged in washer, started to wash clothes. Washer works fine and QUIET. I have yet to find the model number on my Maytag washer. I ordered the pump by sight (good pics).
Was this helpful?
Thank you for voting!
Washer made horrible noise when entering the spin cycle.
1 person found this instruction helpful.
  • Lance D. from Broken Arrow, OK
  • Easy
  • Less than 15 mins
  • Nutdriver, Pliers, Socket set
I removed the cover on the back of the machine, detatched the 2 hoses and removed the 3 screws holding in the Vertical Style Pump - with pulley. These screws are 10 mm nut-driver. The cover if I remember correctly was a standard rather than metric so make sure you have both available.

Screwed new part in, re-attached hoses an d replaced cover. The last step requires strength to hold the machine up and re-configure the belt. This is best accomplished by looping it onto the tub and the pump first, the using the tub pulley to maneuver the belt onto the motor.

Only discouragement was that it took 8 days to receive the part as the first shipment was not the correct part at the fault of the distrutor.
Was this helpful?
Thank you for voting!
pump bering failure
1 person found this instruction helpful.
  • Robert from Englewood, FL
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers, Screw drivers
first i removed the front panel unclamped the hoses unscrewed the 3 screws that hold it in pulled it out, opened the new one and actually dropped it in and it fell into place with the holes lining up inserted the screws and hose clamps and reinstalled the belt which fell off when the old pump was removed, put the front back on and gave it a test then let the wife do a load of wash it worked like new
Was this helpful?
Thank you for voting!
water leaking from under front of washer
1 person found this instruction helpful.
  • Mark from Isom, KY
  • Really Easy
  • Less than 15 mins
after doing some research I found out that a loose or slipping water pump belt could cause the water pump to not pump out the water correctly. Under the washer is the belt. All you do is have someone lift the front of the washer up enough that you can reach under and remove the belt. Then replace the belt back like you took it off.
Was this helpful?
Thank you for voting!
would not engage spin cycle, belt was shredding.
1 person found this instruction helpful.
  • john from mashpee, MA
  • Really Easy
  • Less than 15 mins
pulled the machine out, tilted it backward to expose the bottom. pulled off the old belt. got the new belt started on the three pulleys. pulled the belt to spin it , and...............done !!
Was this helpful?
Thank you for voting!
Had a squeaky belt
1 person found this instruction helpful.
  • Michael from Mokena, IL
  • Really Easy
  • Less than 15 mins
Piece of cake. Raise up the front of the machine. the belt slips of easy by turning the main drive wheel. put the belt on the two small one and then rotate the big wheel as you slip the belt into the grove. good idea to first clean the wheels of any old belt material that may be worn off. Piece of cake!
Was this helpful?
Thank you for voting!
Broken belt needed to be replaced.
1 person found this instruction helpful.
  • Niels from Hopewell Junction, NY
  • Easy
  • Less than 15 mins
  • Socket set, Wrench (Adjustable)
Replacing a belt on a washing machine is a pretty easy process, depending slightly on how easy it is to access the belt. On our Maytag, the belt can be accessed directly underneith the washing machine. So, I lifted the front of the machine and put a few blocks of scrap wood under the legs to hold up the front of the machine. Once that was done, there was nothing else that needed to be removed to access the pullies that the belt had to go around. The motor itself is generally adjustable to allow the belt to be changed. So, I first wrapped the belt around the largest one that spins the washin machine tub, and then wrapped it around the one that spins the water pump. Finally, I loosened the bolt on the motor to allow it to move, wrapped the belt around the motor, pulled the motor back to tighten up the belt, and tightened the bolt that holds the motor in place. It's a pretty straight forward repair that narly anyone could do thmselves.
Was this helpful?
Thank you for voting!
Locked up the machine.
1 person found this instruction helpful.
  • Mitchell B. from Moreno Valley, CA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers, Socket set
Unhooked the macine pulled out for easy access .removed drive belt rear cover plate ,vaccumed remaining water out thru drain hose with wet and dry vac. Removed hose clamps and hoses .removed the three hex screws holding the pump to the base plate. The removed the old pump , Installed the new pump hoses access plate and belt . Hooked the machine up . Worked perfect.











the
Was this helpful?
Thank you for voting!
Wore out Pulley/Bearing
1 person found this instruction helpful.
  • Mark from Akron, CO
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Socket set
Disconnect all water supply and unplug washer. Remove 3 screws on back panel of the washer. This will expose the pump unit. Detach belt on the bottom of the washer. Then detach two hoses that connects to the pump unit. Use pliers if necessary to disconnect hoses. Use 5/16 socket with extension to take out three bolts the connect pump to t he washer. That's it, now replace old pump unit and with new. Place bolts back in the 3 holes, reattached hoses, cover the back with 3 scres. Connect the belt to the pulley system on the bottom. Connect water supply and plug it in.
Was this helpful?
Thank you for voting!
Machine was wailing like a stuck pig!
1 person found this instruction helpful.
  • Jeff from Sugar Land, TX
  • Really Easy
  • Less than 15 mins
Pulled that sucker out from the wall and leaned him back just enough to prop a case a beer under it. Slid up under there with the biggest dust bunny I ever seen. Yanked that old belt off and threw it away. Tried to uncoil the new one and it slapped me in the nose! Got it uncoiled and around the two smaller pulleys pulling the adjustable o ne in to it's limit and walked the belt around the big drum pulley. By the time my wife put down her coffee and came to see if she can lend me a hand I was done!.
Was this helpful?
Thank you for voting!
Whasher would not drain
1 person found this instruction helpful.
  • Robert E from Katy, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Used a water hose to syfen out the water. Placed hose in the tub. Turned outside facet to fill hose. Undid hose outside and allowed to drain. Pulled pump. Order online ( Delv fast 2 days ) .Replaced pump . Works great . Good luck with yours.
Was this helpful?
Thank you for voting!
Water removal pump stopped working.
1 person found this instruction helpful.
  • Timothy from Palmdale, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
Removed lower rear panel by removing 8 screws. Then I removed the two hoses that are attached to the pump by removing the hose clamps with a pair of plyers. The three hex head screws that anchor the pump to the base of the washer unit were removed and the pump came right out. To put the new pump in I just slipped the pump through the hol e at the bottom of the washer and attached the belt onto the pulley. Then reversed the installation process. The washer had to be tipped forward slightly for this process and blocked (approx. 8 in.) to allow access to pulley. Very easy install, no help needed. Washer must be empty and preferable dry when task is done or water will be everywhere.
Was this helpful?
Thank you for voting!
washing machine squeaked on the spin cycle
1 person found this instruction helpful.
  • Jeffrey from Wabash, IN
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
removed hoses and belt. removed 3 screws that secured pump. and then removed pump. received new pump and just reversed the process to repair!
Was this helpful?
Thank you for voting!
All Instructions for the CW18P2WC
61 - 75 of 271