CW18P2WC Crosley Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oil leak from lower lip seal
6 of 6 people
found this instruction helpful.
-
Anthony from CHESANING, MI
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers, Socket set, Wrench set
I didn’t have special tool for brake but punch and hammer worked. Seal was easy to replace. Several videos online to show you how. It wasn’t worth it to tear apart the transmission and buy more parts/seals (if they were even available). But I didn’t know how much oil was in it. I drilled a hole in the side to somewhat check level and
... Read more
added 80-90 gear oil. It was almost empty and added almost a quart. Used a self taping screw/bolt with gasket sealer to plug the hole. I got 34 yrs out of this washer. If it fails, oh well. Just hate to buy a new one that only last 10yrs if im lucky.
Read less
Was this helpful?
Thank you for voting!
Washer went off balance and the flume broke off
13 of 27 people
found this instruction helpful.
-
Michelle from Jupiter, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the part that was still attached to the washer and installed the new flume. It took less than five minutes and a repair that would have cost over $85 cost less than $10 and I am no plumber!
Was this helpful?
Thank you for voting!
Washer Spin Cycle Stopped
7 of 9 people
found this instruction helpful.
-
Diana from La Mirada, CA
- Easy
- Less than 15 mins
-
Screw drivers
Removed the screw from the side of the lid of the washer. Took off the old Lid Switch Actuator and screwed in the new one. Took a little elbow grease because the old screw was tight but no longer than 15 minutes tops.
Was this helpful?
Thank you for voting!
new belt worn out by a bad motor pulley
7 of 9 people
found this instruction helpful.
-
ALBERT from WASCO, CA
- Really Easy
- Less than 15 mins
-
Pliers
i took off the old belt and i took off the motor pulley with the pliers and srewdriver. i put the new pulley in with my hand and gave it a hit with the palm until it snap in and then i put the belt on by rotating the main pulley on tub till the belt was pulley on.
Was this helpful?
Thank you for voting!
Noticed nick in drive belt durng inspection and cleaning
5 of 5 people
found this instruction helpful.
-
Brian from Plainville, CT
- Really Easy
- Less than 15 mins
Washer was making noise especially when spinning. I took the washer apart to clean it, That is what it really needed. Also adjusted the water level to prevent overflows which caused soap and water to get underneath into the drive belt area as well. During inspection noticed a nick in the drive belt, Although this was not really causin
... Read more
g immediate problem wanted to repalce it to prevent problems. Ordered the belt; it came in two days with no special postage. To install, just leaned the washer over on its front on a slight incline. Took old belt off and put new on by turning the big pulley. It is spring tensioned, so no tools. This may be the easiest part repacement I ever did. Took longer to write this paragraph than to repalce the belt.
Read less
Was this helpful?
Thank you for voting!
I had water leaking from the top of the tub.
6 of 8 people
found this instruction helpful.
-
Lester from Elk Grove, CA
- Really Easy
- 15 - 30 mins
I opened up the top of the washer which exposed the tub, I took the top ring off the tub and under in side of the ring is the seal. Took the old one out and put the new one in. The old seal was completely wore out.
It was real easy.
Finding the part is usually the hardest part, but thanks to Parts Select finding the part was ... Read more the easiest part of the repair.
It was real easy.
Finding the part is usually the hardest part, but thanks to Parts Select finding the part was ... Read more the easiest part of the repair.
Read less
Was this helpful?
Thank you for voting!
broken pump, burned belt
5 of 6 people
found this instruction helpful.
-
Jeffery from Omega, GA
- Easy
- 15 - 30 mins
-
Nutdriver, Socket set, Wrench set
I removed four screws to remove a plate to get access to the pump. Then I removed 3 screws to remove the pump. I then put the new pump in place and put the 3 screws back in the pump. Then I put the plate back on and put the 4 screws back in. Then I put the belt on and put the washing machine back in place and connected the water line
... Read more
s and drain line and plugged the washing machine back in and then tested the washing machine to make sure it worked. Job completed.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
lid switch acuator broke and some cycles would not work
5 of 6 people
found this instruction helpful.
-
Brian from Woodbury, MN
- Really Easy
- Less than 15 mins
-
Screw drivers
unscrew the screw holding the broken part in the lid to remove the old part and tighten the screw to a firm position to hold the new piece in place. Now working fine.
Was this helpful?
Thank you for voting!
Water pump failure
5 of 6 people
found this instruction helpful.
-
John from Alhambra, CA
- Easy
- Less than 15 mins
-
Nutdriver, Pliers
Disconnect electricity....remove front panel by gently prying up lid.... Remove two small screws at corners of front panel. You may need small nutdriver here or very small hands, you can easily swivel tub out of the way....once front panel is off water pump is at the bottom right... It is only connected by two squeeze clamps and 3 nuts...
... Read more
This is obviously where the adjustable wrench and nutdriver come in very handy... Otherwise this job will be a bit longer....be prepared for residual water to pour out...you will need towels or a bucket....replace old with new one by reversing the process...at this point tilt the entire washer on it's backside or at least at a 45 degree angle to access the bottom... Swivel the motor away to slack up the belt...remove belt and replace in reverse order of diassembling.... Should take no more than 15 minutes.... Good luck!!!!!
Read less
Was this helpful?
Thank you for voting!
Washer was making noise during spin cycle
4 of 4 people
found this instruction helpful.
-
William from MORGANVILLE, NJ
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
Hardest part was finding part that needed the needed repair. Searching the web for issues associated with the sound resulted in many links. Once the sound was found, I went to the video to see how to remove the Water Pump so I could examine it to confirm that was the correct piece. It took about 15 minutes to remove the part. Since I h
... Read more
ad to remove the belt to get it out, I realize that the belt needed replacement as well. So both parts were ordered. Replacing the parts also took about 15 minutes. Relatively easy repair. Be aware that the video on the part select video shows the water pump in a different location than the Maytag washer. To get to the Maytaq water pump, there is a panel in the back that had to be opened to access the water pump.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer always going off balance full loads or small
3 of 3 people
found this instruction helpful.
-
Jeffrey from HONEY BROOK, PA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Socket set, Wrench (Adjustable)
I tilted top cover to remove front washer panel removed suspension springs to remove complete tub assembly to gain access to bottom. Drive pulley to remove snubber ring I performed the repair step by step as per your video. was dead on made the repair go smoothly. I installed the belt last tilting washer mechine back to gain access to und
... Read more
ercarrige just walked belt on all three pulleys self adjusting then. made sure washer was level. Front to back side to side no rocking in any deriction My wife did four full loads problems gone I think all needed to be done to complete repair snubber ring , washer drive belt, & leveling machine all played there roll in putting washer back in factory working condition washer not a angery walking vibration nightmare
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer was making a squeak during spin cycle & then just stopped spinning
3 of 3 people
found this instruction helpful.
-
Eleanor from PALATKA, FL
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I watched the video of the repair on this website and followed it. Was really easy & THANK GOD because this was my first repair. This has been a great machine and it looks like it will continue to be for a little while longer! Thanks for the video help and friendly navigation of your site!
Was this helpful?
Thank you for voting!
Leaking water inlet hoses.
4 of 6 people
found this instruction helpful.
-
Helen from NASHUA, NH
- Really Easy
- 30 - 60 mins
Removed the old hoses and screwed on the new hoses.
Was this helpful?
Thank you for voting!
White fluffy residue appeared under washer. Unbalanced banging during spin cycle
4 of 6 people
found this instruction helpful.
-
John from Blue Bell, PA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
Parts needed: Snubber Ring and 6 Springs (don't put the old springs back)
Unlug the AC cord, open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back It was not necessary to rem ... Read more ove the back cover. Remove the little hose going to the basket from the control module. Remove the 6 springs and lift the complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING: DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK. Seriously! Install the new ring, center and tighten the screws. Put the tub back in. I found it handy to support the tub with a 2x3 to get the springs back in. Connect hoses back up. It really isn’t that bad, a couple of scraped knuckles.
Unlug the AC cord, open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back It was not necessary to rem ... Read more ove the back cover. Remove the little hose going to the basket from the control module. Remove the 6 springs and lift the complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING: DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK. Seriously! Install the new ring, center and tighten the screws. Put the tub back in. I found it handy to support the tub with a 2x3 to get the springs back in. Connect hoses back up. It really isn’t that bad, a couple of scraped knuckles.
Read less
Was this helpful?
Thank you for voting!
Our washer was purchased 1/6/2006 and it started banging and walking out of its place when the washer started into the spin cycle. This would occur no matter the size of the load.
3 of 3 people
found this instruction helpful.
-
Pamelia from LA CROSSE, VA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
We followed the instructions show on the video. However, our model was assembled slightly different. We had to remove the screws from both sides of the side panels so that we could remove the tub from inside of the machine. Also our model only has one belt not two.
Over all it was easy considering my husband and I had never attempte ... Read more d to repair a washer. Once we got it back together it when back to working like it had never been broken!
We would have never been able to repair our washer without the video that your site provided... thanks so much!!??
Sure wish the manufactures would consider making the older models again as lots of us are not happy with the new modules being manufactured presently!
Over all it was easy considering my husband and I had never attempte ... Read more d to repair a washer. Once we got it back together it when back to working like it had never been broken!
We would have never been able to repair our washer without the video that your site provided... thanks so much!!??
Sure wish the manufactures would consider making the older models again as lots of us are not happy with the new modules being manufactured presently!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!