EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

CW18P2AC Crosley Washer - Instructions

All Instructions for the CW18P2AC
121 - 135 of 260

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
the lower panel rotted away and damaged the pump
0 of 1 people found this instruction helpful.
  • kenneth from wayland, NY
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
this email does not include the rest of the parts i ordered. i had to replace the pump and the base panel of the washer as it was rotten. i had to open the top, remove the front panel and change out the base and install the pump. your parts and website were very helpful. thank you however this will be the last maytag i will purchase .
Was this helpful?
Thank you for voting!
Water would not drain and tub would not spin.
0 of 1 people found this instruction helpful.
  • Larry from Waukesha, WI
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
I had to raise the top of the washer and take off the front pannel. It was not too hard to replace the pump except that it was in the back corner and it was hard to reach the bolts to remove and install the new pump.
Was this helpful?
Thank you for voting!
drive pulley broke off from drain pump
0 of 1 people found this instruction helpful.
  • John from Pomfret, MD
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Raised washer. Identified problem. Removed from panel, gaining access to drain pump. Removed hoses, replaced pump. NOTE: I used blue Loctite on pump mounting bolts. Reinstalled from panel, lowered washer, cleaned drum. Ran one (1) cycle with hot water and bleach ONLY.
Was this helpful?
Thank you for voting!
Washer going out of balance
0 of 1 people found this instruction helpful.
  • Brian from Rock Hill, SC
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Tilted washer back and removed belt
Lifted front of top and propped up
Unscrewed two screws and removed front of washer
Disconnected two drain lines from tub
Disconnected 6 springs from tub
Removed tub
Popped off bottom plastic cap
Removed locking ring
Slid off gear from shaft
Unbolted screws f rom snubber support ring
replaced snubber
Put everything back together in reverse order

Worked like a champ!!!!!
Was this helpful?
Thank you for voting!
Vibration
0 of 1 people found this instruction helpful.
  • Richard from Jacksonville, FL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Troubleshoot problem, removed front, removed drive belt, removed pump with pulley. Note, new pump did not have black plate, installed worked great.Thanks
Was this helpful?
Thank you for voting!
Belt was frayed and pump was leaking.
0 of 1 people found this instruction helpful.
  • Glenn from Kansasville, WI
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
I removed the back panel and then removed the old pump. After attaching the new pump I flipped the machine and attached the new belt. I put everything back together and voila, the machine works.
Was this helpful?
Thank you for voting!
Washer shook and danced on basement floor
0 of 1 people found this instruction helpful.
  • Bruce H from Mason City, IA
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers, Socket set, Wrench set
I found on-line that replacing the snubber ring may fix the problem and ordered the part. With the instructions also downloaded I started taking the washer apart. Without the instructions the task would have been more difficult and possibly disastrous as I might have taken the bolts out that tighten down the snubber ring. All went well wi th a little patience. The washer works good.
Was this helpful?
Thank you for voting!
Had some difficulty placing pulley back in place
0 of 1 people found this instruction helpful.
  • Oscar from Weslaco, TX
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers, Socket set
Laid washer on its side, released five of the six tub springs, then removed the dive belt and the main pulley. With some effort removing the old snubber ring, placed the new snubber in place. After fighting with the large spring under the pulley I was able to replaced the six screws with the help of an assistant. Replaced the pulley, b elt and the five springs. Closed the unit up and placed all the hoses back in place. I was amazed at how smooth the washer functioned with no vibration at all! Thank You.
Was this helpful?
Thank you for voting!
when in spin cycle it would shake rattle &roll
0 of 1 people found this instruction helpful.
  • Marvin from Manteca, CA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers
open top,remove back panel.then laid on the side and removed belt.remove hose from tub to pump.removed small hose for fill level.Hard part was to remove springs from tub.Then pull tub and transmission out of housing.Remove pulley from shaft.Lossen screws around snubber ring but do not remove them.Remove old snubber ring.clean surfaces wit h alcohol.install new snubber ring and assemble in reverse order.
Was this helpful?
Thank you for voting!
My washer had stopped turning. It wouldn't wash or spin but the moter was still working.
1 of 5 people found this instruction helpful.
  • Evelyn from Temple, TX
  • Really Easy
  • Less than 15 mins
We're not repair people. So when calling around for the replacement belt no one had it. Everyone said that the belt went to a dryer. We simply inspected the machine. Located the worn belt which was on the bottom of the washer machine went online and ordered the belt. Thank you so much you guys really saved me. I will always recommen d you all to everyone that I know. Your system works Great! Thanks Part Select!
Was this helpful?
Thank you for voting!
pump leaking, washer would not spin right
0 of 2 people found this instruction helpful.
  • Jim from Lincoln, DE
  • Really Easy
  • Less than 15 mins
  • Pliers, Socket set
I got the part the very next day, very easy to replace. Replaced the belt as well. Parts Select is the best. Vert straight forward repair.
Was this helpful?
Thank you for voting!
belt was shredded
0 of 2 people found this instruction helpful.
  • Eric from Atascadero, CA
  • Really Easy
  • Less than 15 mins
I turned washer over, took off old shredded belt. One of the pulleys is spring loaded so I just held it in as i looped the new belt on. Easiest repair I have made on a washer!
Was this helpful?
Thank you for voting!
Worn bearings on pump, awful screeching noise
0 of 2 people found this instruction helpful.
  • jim from pasadena, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Unplug. Open the front panel (2 clips, 2 hex head metal screws), remove the two hose clamps and hoses from the pump, remove 3 hex head screws holding the pump...bingo.. in with the new pump, hoses and panel go back....put the drive belt back on...the wife is back in buisness.. Note to all husbands out there, mess up on a few loads of lau ndry (mix red with white and her unmentionables turn a hideous pink) and you never have to do laundry again !!!!
Tip to all, if you have a wet-vac, attached it to the discharge hose of the washer to remove the standing water in the pump.

Right part, right price, delivered right on time Thank you Parts Select
Was this helpful?
Thank you for voting!
washer was going out of balance
0 of 2 people found this instruction helpful.
  • Loren from Glennallen, AK
  • Really Easy
  • 15 - 30 mins
  • Pliers, Socket set
watched youtube on how to change out the snubber ring. it was quite easy.
Was this helpful?
Thank you for voting!
snubber under the tub
0 of 2 people found this instruction helpful.
  • antonio from ellenwoo, GA
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
got the right part great service from partselect invited my bro in law 20 mins we where done.. no more violent shaking spin cycle thank you very much
Was this helpful?
Thank you for voting!
All Instructions for the CW18P2AC
121 - 135 of 260