EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

CW18P2AC Crosley Washer - Instructions

All Instructions for the CW18P2AC
91 - 105 of 260

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Started making loud screeching noise(bad Bearing)
1 of 2 people found this instruction helpful.
  • Michele from Lebanon, PA
  • Easy
  • Less than 15 mins
  • Pliers, Screw drivers, Socket set
Turned water off,tilted unit forward,removed lower rear cover,removed belt,laid towels around ,removed inlet hose and exit hose off pump,removed 3 screws holding pump,removed pump and installed new one,reversed order of disassemble, has been running great ever since.
Was this helpful?
Thank you for voting!
Made noise on spin cycle
1 of 2 people found this instruction helpful.
  • Les from Moneta, VA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Took off belt and ran motor. No noise. Then took off drain pump and spun it by hand and felt rubbing on one spot. I figured the bearings were going bad, so I ordered the parts and replaced them.
Was this helpful?
Thank you for voting!
machine was starting to make noises when spinning
1 of 2 people found this instruction helpful.
  • Virginia from Rockford, IL
  • Really Easy
  • Less than 15 mins
My husband unhooked the water lines, unplugged the washer and remove the waste water hose, then we tipped it over and easy as pie the belt came off and the new one went right back on. I did not see any tears or breaks in the old belt, but it was stretched out a bit, and the washer is once again quiet. This also gave me an opportunity to clean under the washer, which we all know we don't do unless we have to. Cheap, quick, and easy fix for someone to do there self.
Was this helpful?
Thank you for voting!
Washer making loud noise and tub off balance
1 of 2 people found this instruction helpful.
  • Hollee from Rancho Mirage, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
I followed Gary from Sioux City IA instructions. Very well explained.
Was this helpful?
Thank you for voting!
noisy out of balance during spin cycles
1 of 2 people found this instruction helpful.
  • Ronald from Wading River, NY
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Socket set
I followed the instructions that other posters suggested. The springs were the toughest part to remove and reinstall. Having my wife push the tub enabled me to use vice grips to get them back on. Read about the coins or washers to spread the springs too late... would have helped. Running a wash now and it's spinning great and no noise !
Was this helpful?
Thank you for voting!
machine woulden't spin properly
1 of 3 people found this instruction helpful.
  • Richard from Ponte Vedra Bch, FL
  • Really Easy
  • Less than 15 mins
  • Nutdriver
diagnosed a loose belt-- ordered and received same -- installed and set to proper tension that was simple.
Was this helpful?
Thank you for voting!
Pump was making a grinding noise.
1 of 3 people found this instruction helpful.
  • Daniel from Hinsdale, IL
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
I tilted the machine on it's back to remove the drive belt. You could feel the friction in the pump when you turned the pulley. I set the machine back down and removed the back cover (4 screws). I removed the two hoses with a pair of pliers. I used a small socket set to remove the three mounting screws. I ordered the pump. I reversed the process to put it back together. It took about 35 minutes to determine what the problem was and to remove the pump. It took about 20 minutes to put it back together.
Was this helpful?
Thank you for voting!
Washer was leaking water.
1 of 3 people found this instruction helpful.
  • Steven from Atlanta, GA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Socket set, Wrench (Adjustable)
Removed front of washer following instructions on partselect.com (used putty knife to release catches). Removed hoses and belt from pump, then removed and replaced the pump. Reattaching the belt was the only awkward task.
Was this helpful?
Thank you for voting!
Noisy Pump
2 of 7 people found this instruction helpful.
  • Frederick from Yuma, AZ
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
I placed the washer on a couple of work-horses so I could have access to the belt underneath. Then I used my nutdriver to removed the lower back panel. Disconnected both of the hoses, and removed the pump with my nutdrivers. Placed the new pump in place, placed the belt back on the pump's pully, tightened down the pump. I then plugged in the washer and put a little water in the washer to test that everything was working. After confirming that everything worked, I replaced the lower back panel and put the washer back in business. 30 minutes from beginning to end ... and a good time was had by all.
Was this helpful?
Thank you for voting!
Washer making loud noise when water pump operating, still worked but made very loud noise
0 of 1 people found this instruction helpful.
  • Buddy from Ogden, UT
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
I ordered the replacement pump assembly (water pump)for my Atlantis model maytag washer, removed the old one, installed the new one and works like a charm. The only difficulty I had was trying to figure out how to remove the cover on the front of the washer, to remove the clips, it slid side to side instead of popping out, found the inst ructions on-line, NO instructions came with the pump but if you have any common sense when it comes to repairs it was easy to remove and install the new part.
Was this helpful?
Thank you for voting!
washing machine filled with water, nothing else happened.
0 of 1 people found this instruction helpful.
  • Ellie from Eastview, KY
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Spoke with a trusted repair man, described the problem best as I could. I smelled a burning rubber smell. Got on Internet for troubleshooting problems, 77% likely a drive belt. BINGO! Ordered a new belt, took old one off, cleaned the pulley ( it had burnt rubber stuck on it, difficult to remove) lightly sanded pulley just so it would be r eally smooth. replaced belt. Magic, it worked. I am no repair woman, but carefully listening and explaining helped. Oh, belt is under the very bottom of machine. Very easy to get to, just tilt back and lodge at an angle and make sure it doesn't move.
Was this helpful?
Thank you for voting!
dead pump
1 of 4 people found this instruction helpful.
  • Andre. M from Glendale, CA
  • Really Easy
  • 15 - 30 mins
  • Socket set
I first opoen the front panel of the washer. That was a bit tricky. Had to slide a thin blade between the top of the washer and the front panel, pushed in to release the "clamp" and gently raise the top, it hinges on the back.
The rest was undoing three bolts, refit the new pump and put the belt back on.
The part cost me less then $65.00.
The repair estimate by the local repair man was $ 250.00.
I am very happy.

Thank you PartSelect.

Andre M. Roberty
Was this helpful?
Thank you for voting!
loud sqeaking noise, burnt rubber smell, motor siezing up
0 of 1 people found this instruction helpful.
  • Ricky from Colorado Springs, CO
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Unplugged electrical plug. Disconnected water and drain hoses. Turned washer on front side. Removed old belt from bottom of washer. Removed pump access panel. Removed old pump. Installed new pump. Torqued pump mounting screws 1/4 turn with socket wrench. Installed new belt. Put on pump access panel. Hand tested motion of belt and pulleys for smooth travel. Put drain hose on. Turned washer in the upright position. Reconnected water hoses. Washer works like new.
Was this helpful?
Thank you for voting!
loud noise while washing, spinning and draining
0 of 1 people found this instruction helpful.
  • Julia from Columbia, IL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
took off back small metal panel, tilted washer front side down, easy to put into place after removing old part
Was this helpful?
Thank you for voting!
Squealing Belt In All Cycles
0 of 1 people found this instruction helpful.
  • TERRY E from TUCSON, AZ
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
Because I live alone, the washer is very heavy so I just used some sliding robots under the legs of washer so I could slide it out from the wall by myslef after removing the small plate in the back to accfess the water pump I used the nut driver to remove the 3 screws holding the pump in place, but I used the pliers to remove the 2 water hoses first then I mounted the water pump back into place, installed both hoses again then I tilted it back against the wall while re installing the belt then I pushed it back against the wall and removed the sliders so I could make sure it was back level this was a very easy repair even if you never fixed any thing before the belt replacement was even more simple to replace because the motor is springloaded so you just had to pull on it enough to remove it from the pulleys
Was this helpful?
Thank you for voting!
All Instructions for the CW18P2AC
91 - 105 of 260