CW18P2AC Crosley Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer noisey during spin dry
0 of 1 people
found this instruction helpful.
-
Edwin from Green Valley, AZ
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set, Wrench set
Had wife balance washer on front edge while I accessed working parts from bottom of washer. Removed drive belt and turned agitator pulley, transmission pulley and drain pump pulley by hand. Drain pulley hard to turn and shaft had play in it. Ordered new drain pump and replaced upon receipt. Very few fasteners to remove and replace pum
... Read more
p assembly. Drive belt was easy to remove and replace. Recommend also replacing drive belt on a washer this old.
Read less
Was this helpful?
Thank you for voting!
Washer Walking Across Floor,From Being Off Balance
0 of 1 people
found this instruction helpful.
-
Kenneth from Griffith, IN
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
1- Unplug unit 2-disconnect water hoses 3-put unit in open area so you can work on it. 4-Open top cover with screw driver 5-take off front cover with appropriate socket 6-lay unit on it back to get access to the drive belt (take off). And take off water hose with plyers. 7-With vise grips take off the six springs. 8-Take tub assy ou
... Read more
t,and lay it on the floor upside down. 9-Loosen the screws to take out the old snubber ring, note ( when lossening screws,keep your finger on the bottom of the screw ,so you can feel how far to back the screws out,just enough to have access to the snubber ring,to take out,and install new one. )Remember not to take screws out completely. The unit is under spring tension. 10-Put washer back together in reverse order,and problem solved!
Read less
Was this helpful?
Thank you for voting!
Pulley Bearings Siezed; Pump Quit
0 of 1 people
found this instruction helpful.
-
Robert from Columbia, MO
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
Turned it over to my 35-year old son who removed pump and pulley assembly and the old drive belt, then simply replaced with new assembly and belt from PartSelect! Could not have been easier - from my viewpoint.
Other Parts Used:
Was this helpful?
Thank you for voting!
Needed to replace the water pump
0 of 1 people
found this instruction helpful.
-
Theresa from Zanesville, OH
- Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Wrench set
The Clamps for the hoses were difficult to get to, otherwise was a simple replacement job, involving clamps and screws and bolts.
Was this helpful?
Thank you for voting!
Bearing on pump making noise and would go out soon.
0 of 1 people
found this instruction helpful.
-
Marcus from Camarillo, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I diagnosed the bearing by putting a 3/4 inch rubber hose up to my ear. I pointed it around until isolating the noise to the pump. The bearing was not servicable without replacing the pump. After diagnosing the problem I ordered the part. Getting the part from PartSelect.com was a snap. It arrived in one day. In 15 minutes I had it back t
... Read more
o gether and working quiet and smooth.
Read less
Was this helpful?
Thank you for voting!
washer shaking
0 of 1 people
found this instruction helpful.
-
Jerry from Troy, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Socket set
took drum out replase snubber put drum back in
Was this helpful?
Thank you for voting!
Washing machine had difficulty in spine cycle
0 of 1 people
found this instruction helpful.
-
Stephanie from Ticonderoga, NY
- Really Easy
- Less than 15 mins
Unplugged everything, disconnected hoses, took belt off and put new one on.
Was this helpful?
Thank you for voting!
Bearings in mechanical pump seized.
0 of 1 people
found this instruction helpful.
-
Scott from Idaho Falls, ID
- Easy
- Less than 15 mins
-
Pliers, Socket set
Unbolt old pump with three bolt from top of pump inside the washer. Use needlenose pliers to remove intake and output hoses from old pump. Remove belt from pulley under washer. Reverse procedure to install. I was worried because there were two pumps listed for this model number, one being $95 and the other being $40. I bought the cheaper
... Read more
one and prayed. It worked just fine. Fixed a $500 washer that was on it's way to the dump and made $100 in the process!
Read less
Was this helpful?
Thank you for voting!
noisy pump
0 of 1 people
found this instruction helpful.
-
Tery from Orange, CA
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Removed back plate, tilted up washer removed pump removed belt. Then replace pump and then replaced belt
Other Parts Used:
Was this helpful?
Thank you for voting!
worn drive belt
0 of 1 people
found this instruction helpful.
-
James from Shortsville, NY
- Really Easy
- Less than 15 mins
tilted the machine forward, worked off the old belt and put the new belt back on. no tools required, done in less than 5 minutes.
Was this helpful?
Thank you for voting!
Washer Machine just shut down.
0 of 1 people
found this instruction helpful.
-
Patrick from Indianola, MS
- Really Easy
- Less than 15 mins
All i had to do was pull the washer machine from the wall and lean it back as far as i could and get under it and place the (DRIVE BELT) on the two smallest pulley then put the belt on the large pulley and my work was done it was very simple and easy.......
Was this helpful?
Thank you for voting!
Made an awful sqealing noise and did not spin the water out all the way
0 of 1 people
found this instruction helpful.
-
Deborah from Baltimore, MD
- Really Easy
- Less than 15 mins
-
Socket set
Leaned the washer back and propped it up and changed the belt. This is the first time ever repairing an appliance. I feel very good about myself as I am 49 yrs old and did not have to call a repairman for this.
Was this helpful?
Thank you for voting!
Washer would not go into spin cycle.
0 of 1 people
found this instruction helpful.
-
Jack from Scottdale, PA
- Really Easy
- Less than 15 mins
I pulled the washer away from the wall so that I could lean it back at an angle. I removed the old belt and put the new one on. I started with the smaller pulley first and put the belt into the groove. Next I went to the next larger pulley and did the same thing. Then I went to the largest pulley and started to put the belt into the groov
... Read more
e and started turning the pulley by hand. The belt went right on.
Read less
Was this helpful?
Thank you for voting!
drive belt broke
0 of 1 people
found this instruction helpful.
-
Gerard from Keansburg, NJ
- Really Easy
- Less than 15 mins
pulled out the washing machine that was the hard part, tilted it back checked too make sure everything spun by hand just to see if that was reason for the belt to snap but everything spun by hand nice and smoothly poped on the drive belt and everything works fine back in business.
Was this helpful?
Thank you for voting!
Under belt was used and ready to let go..
0 of 1 people
found this instruction helpful.
-
Melanie from Tamarac, FL
- Really Easy
- Less than 15 mins
First I am a woman and was able to do it, and if I can do it anyone should be able to do this. The service call alone was 75.00, and the belt was 23.00 with shipping. First we tilted the washer at a 45 degree angle and I removed the belt, and just rolled the newer one on the track. That was it and I was done. My washer now purrs like a ki
... Read more
tten love it. And Part Select sent out my part and I recieved it next day, thank you for wonderful service that kind of service is hard to find. <3
Read less
Was this helpful?
Thank you for voting!