CSX19LABEWH Hotpoint Refrigerator - Instructions

I removed the drawer and glass shelf, removed 2 screws and replaced with new drawer slide in reverse order. I removed the contents of the door, the top hinge, and then laid the door down. On the bottom of the door, I replaced the pivot piece (provided) and then I replaced the hinge on the lower right side of the refrigerator box (2 screws with a nut driver bit). I now reversed the order to re-assemble the door and finally re-aligned the top hinge to adjust the door fit. Less than 30 minutes total. EASY!

Parts select sugested checking the freezer side on the side by side if there was frost on the back panel. I took the back panel off on the freezer side inside the freezer. I found that the freezer coils were full of ice.Had to use a hair dryer to melt all the ice. The heater element was bad on the bottom of the freezer. I ordered a new defrost element an installed in 40 minutes and is running fine.You can still use the refrigerator until the new part comes in if you melt off the coils.It will last about 2 weeks.

This is a repair INSIDE the freezer. Turned off unit.. Unplugged. Removed shelving on freezer side. Removed freezer draw rails (4 screws total.) Removed 2 screws that hold rear panel in place at rear of freezer side (this is inside the freezer). Carefully removed metal panel by pulling from the left (side that does not have shelving clips. As noted on this website and other users, the freezer coils were incased in ice. Thawed with a hair dryer (put towels in bottom of freezer-ice was pretty heavy in mine). When thawed, remove heater element by removing 2 screws that hold it to the aluminum bracket. Then remove wires on each end. Simply install the new emelment by attaching wires back on heater and screw new unit in place. (My original heating element was a single element-you could very easily see where the heating coil inside the glass tube had shorted out. My replacement heater was a 2 element unit. This did not pose any problem at all-installs in the same manner-good directions are provided.). Replace all parts in reverse order. It's that simple. Saved probably $150. This site is wonderful! Fast shipping and the users install tips/notes are fantastic!! Will shop here again if I have to (have a Maytag washer that isn't draining and going into spin-bet the fix is on here somewhere!

Considering that I am a woman who knows nothing about repairing or let alone anything about refridgerator parts etc.... It was very easy.

First I went on line to see if I could even figure out what may be the problem with my refridgerator. After hearing similar stories on this site I thought I would try to order a new heating element since it wasn't that expensive and hopefully save me lots in $$$ have a repair man come out.
I removed the shelves in the freezer portion and then removed the back panel. I had to wait for the freezer to defrost, then I removed the burned out heating element which is about 10 inches long and replaced it with a new one.
It was so simple and probably would have taken less time if I had the freezer already defrosted.
Now the refrigerator is working like new and I fixed it all by myself without the help of my husband!!!!

I had done this repair almost exactly 2 years ago. I also read in this forum about a guy who said he had to do it every 2 years... bad part design.

However, GE has replaced the original single element with a dual element, and that is what PartSelect sent me. I had to splice one wire, but the instructions were clear and it went like a breeze. Oh, and the part arrived less than 3 days after I ordered it with standard shipping. Way to go, guys! Thanks!

I removed food, then removed shelves.
The light bulb and shade had to be taken out.
removed two screws from interior back panel.
defrosted cooling coils
removed two screws from defrost heater
took off two wires ...done
reversed procedure to finish installation

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.Threw away the old defroster. Put the new one in. I had to reroute the blue wire over to the right hand side and plugged it in.Put the back on. put the shelves in and I was done! We had this done just about 3 years ago and it cost us about $175. The cost of this repair was only $38.05 with shipping and all! What a great deal! Thanks so much PartSelect!

First I removed the drawers. Then I removed the 2 screws from each side. Then replaced the 2 pieces in the same manner using the same screws. It took about 15-20 min. Very easy. Drawers work perfectly now. Glad I found this site.

The repair itself is super easy. The heater harness comes with instructions that is easy to follow. The only issue I encountered is that my refrigerator had 1 heating element and you will get one with 2 heating elements. Because of this, the new connectors are on 1 side. Since my old heater had 1 connector on each end, 1 wire is too short if you route both wires the same way as before. The kit comes with an extra wire and directs you to splice the short wire and attach the extra wire with the included connector. I figured a refrigerator with a spliced wire is not a good combination so I rerouted the short wire to the other side along with the other wire. This allowed me to connect both wires without using the extra wire.

Removed shelves and light bulb cover. Then removed the two screws that hold the back wall of freezer compartment in place and removed cover. Thawed ice jam with hair dryer. Removed the two screws holding heating element in place and pulled element out far enough to disconnect the two wires. Reconnected wires to new element and put everything back together.
Installation instructions which came with new part were accurate and very easy to understand.
It took about 30 minutes total.

I followed the easy instructions included with the replacement part I ordered. I removed the back of the freezer, unpluged the broken heater and replace with the new heater. The heater just plugged in, very very simple. I put the back panel bach on with the two screws and it perfectly. Not back for a girl!

Very easy. Just removed the two screws holding heater element in place. I disconected the wires on both ends then re-attached the two wires to the replacement heater and put both screws back on and WHALA! Done!

Well, first I googled the problem and the model and found my way pretty quick to you guys. I sent a note to Tom P., who confirmed that I was looking at the right things. Then I offloaded everything from the freezer and fridge to the RV fridge and chest freezer, unplugged it and used my hair dryer to melt the ice on back plate so I could remove it.

I removed the two small screws at the top of the back, below the icemaker and light bulb, and slid the back cover up and out. Since my coils were pretty heavily iced, it took about half an hour to melt enough that I could get the defrost heater out and check it for continuity, which it failed.

The replacement design is slightly different (2 heater coils vs 1 and connectors on one end), but functionally the same. When putting the new one in, you need to re-run the blue wire down the same side as the pink wire because the connectors are on one end. Mine was long enough to work, but they include a splice kit in case yours isn't.

It took me longer to get the cover back on than to replace the heater assembly! Everything is back to normal, had ice cubes within a couple of hours...
Thanks for your help!

I had this problem before and I knew it was related to the heater located in the freezer section. With the help of the drawings in the parts selct webpage I was able to identify the part I needed within 5 minutes. I ordered the part abd in 3 days I had it delivered.
I followed the instructions that came with the part step by step and I got my refrigerator up mand running in about 45 minutes.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires..