CSX19LABEWH Hotpoint Refrigerator - Instructions

First I removed glass shelf on top of rail. I then removed the two screws holding rail to refrigerator side. Next I installed new rail using same two screws. Finally I replaced glass shelf on top of rail.

took 2 philips screws out,took off rail,and then nreverse.these steps,

Removed 2 screws replaced new part very easy

Removed panel, then removed single coil unit and replaced it with double coil unit that was sent to me. Refrigerator now working fine.

I didn’t do the repair because I ordered two grommets. When they arrived, one of the packages was empty! Instead of just sending me another one, they refunded the part so I still need one. By the way, I was not refunded half the shipping either which was more than the part itself.

Followed the video describing the repain and the written directions. The Video is excellent and made the job easy to follow

This fridge had this same problem 4 other times, each time about 1 yr apart. Being as I considered myself ''mechanically challenged'' my wife always contacted her favorite appliance repair man. However, he was unavailable, so wife was gearing up to go ahead, bite the bullet, and buy a new fridge. We really didn't want another bill to worry with so she suggested I try the repair myself. She'd watched the repairman do it the last couple of times and ensured me it would be ''a piece of cake'' plus save us some bucks and put off an added expense at least a little longer. Ordering the part from this site was simple. The fridge did have the old 1 bulb element and the new one was the 2 bulb element so I was afraid I'd have to do some splicing, but lucked out and the wire was easily redirected and reached without any stress or problems to plug into the new part. She watched the install video and was able to talk me through it without any problems. We saved at least $125 install bill, plus put off making a big item purchase a while longer. I hope the new 2 element defroster does a better job and we might just get 10 more years out of 'old faithful'!

The repair is pretty straight forward it is the preparation that takes time.
The food in the freezer portion of our side by side began thawing. We tried adjusting the temperature level to colder but to no avail. When we started emptying the freezer compartment I noticed a large amount of frost/ice at the back.
I turned the control to off and began defrosting the freezer using my wife's hair dryer. :) Once the outside layer was defrosted I removed the panel covering the coils. They were packed solid with ice and took over 30 minutes to defrost. Be sure to use a pan or container to catch some of the water because the catch pan under the refrigerator isn't large enough.
Once everything was defrosted I removed the heater tube assembly (at bottom of coils)it was a glass tube with a coiled wire element inside. The element had shorted out and the tube appeared black in that area.
I replaced this single tube heater with the double tube recommend on the partselect.com site. This required re-routing one of the wires and splicing in the plug/wire assembly contained in the repair kit.
Simply followed the instructions, reassembled everything and turned the control back on. No more problems. A very easy repair for anyone mechanically inclined and who owns a few basic tools.

Really simple, I used a can of soup and a small piece of wood set under the door, and tapped it tight with the hammer to hold it in place while I removed the hinge. Two bolts at the bottom and two under the door itself. Installed the new hinge set, bolted tight and removed the shim.
The whole thing took less than 5 minutes

It seems my refrigerator was old enough [1987] that the spacing on the holes for the bracket were different than the part that is currently sold. The holes on the new bracket were 30 mm apart on center, but on the old bracket they were 20 mm apart on center.

Clamped the old and new brackets together in a vise to use the old bracket for spacing and drilled a new hole through the 4mm of steel.

After which it was a snap installing the new hinge assembly.

Separately (from a different site) purchased new compressor fan and motor. I purchased the grommets here because the other site listed the grommets as temporarily out of stock. I did watch one of the videos on PartSelect about the grommet replacement. Repair was pretty simple, biggest challenge was getting to the screw on the far side of the motor. Removed the two screws holding the fan motor into place. Removed motor and blade. Reinstalled with new fan blade, new grommet and new motor.

Unplugged the refrigerator then used the cordless drill to remove the 6 screws on the access panel on the back of the fridge to be able to get to the fan. Was able to pull the fan off by hand and push the new fan on by hand. Plugged the refrigerator by in and watched the fan run for a few minutes then replaced the access panel. Really quick and easy repair.

Fortunately while my refirgerator was still under warrant I had this same problem and watched the repairman fix it. To confrm my suspicions I cleaned out the freezer compartment, removed the back panel (2 screws), and used a hair dryer to defrost it. I suggest plugging the drain hole or laying a towel in the bottom of the compartment to catch the run off or your drain pan could over low. Once defrosted I was able to verify that the element on the defrost heater was burnt. Since it was Sunday I re-assembled and cranked it back up until I could get the part. I did a goggle search on Monday, found the part instantly using only the model number from the refrigerator at PartsSelect.com. The part arrived Wednesday as promised, I repeated the process from Sunday, removed the defective part (2 screws & 2 plug in type wire connections) and she works like a charm now. I do think the manufacture of the part should consider a new design since this is the second one my unit has needed in less than 5 years. At only $27.50 ea. I should have purchased a spare to have for the next time!

First I placed a 2x4 under the frig door to keep it in place while I removed the hinge on the bottom of the door. I removed two screws holding the hinge and one screw holding the washer in place. I also loosened a screw adjacent to the washer so that I could more easily remove and replace the washer. The parts went in easily. The repair took much less time than I anticipated.

I removed the top hinge by removing three screws, I then lifted the door off the bottem hinge and set it aside. I then removed the two screws holding the bottom hinge,removed it and installed the new part. I removed the broken part from the door by removing one screw-installed the new part and set the door in place and reinstalled the top hinge. The door is now properly aligned and working like new. I spent as much time writing this as I did on the repair