ALW2 - Parts

This package contains a new set of six springs. The suspension springs in your washer connect to the bottom of tub, and help to hold it in place. If your washer tub shakes, or moves around a lot during operation, it could mean that one or more of your springs are damaged or stretched. You will need to access the bottom of the tub for this...Read more repair by removing the front (and possibly the rear) panel. You will also need a pair of locking pliers to remove the old springs and reconnect the new ones. It is recommended to apply a small amount of grease to the bottom of the new springs before you reconnect them to the washer tub.

If your washer shakes or vibrates loudly when it reaches its max speed, make sure the 4 levelling legs are even. Adjust the legs so that the machine is level, and tighten the locking nuts on the legs that are threaded. Your washer should be kept as close to the floor as possible. Your model might have rear legs that level themselves, or i...Read moret might have threaded legs all around. Make sure the rubber feet have not worn out. Replace any missing or damaged legs and feet. This genuine OEM replacement part is sold individually, so be sure to order the amount you need.

This screw is sold individually.

This shaft is made to fit the center of the idler pulley wheel of many clothes dryers. It is less than two inches long, and is made of metal.

This wheel has a center metallic bearing. A dryer's idler pulley wheel serves to help the belt to rotate the drum.

This spring retaining clip is just under 1 inch long. The clip is made entirely of metal and is attached to the back wall of the washer, under the console. If your washer is vibrating and louder than usual during the wash cycle, your spring retaining clip could be faulty or damaged. Check the clip for visible damage, wear, and rust. If yo...Read moreu notice any signs of damage, the part should be replaced. Remember to disconnect the power from your washing machine before starting this repair.

This v-style spin and agitate belt is 28-3/4 inches long and half of an inch wide. It is all black in color and made entirely of rubber.

The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be care...Read moreful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.

This washing machine cleaner includes three time-release tablets designed to remove odor-causing residues, grime, and buildup from high-efficiency and top-load washing machines. The tablets work by cleaning the tub, pump, and internal components, helping to eliminate unpleasant smells and maintain optimal performance. Safe for use with se...Read moreptic systems, this cleaner is intended for monthly use?simply place one tablet in an empty washer and run a Normal Cycle with hot water or a Clean Washer Cycle. Regular use can help extend the life of the appliance and ensure fresh, clean laundry results. Always follow the instructions provided for best results.

This water valve is for 60% hot water and 40% cold - This is done to save on energy.

Sold individually. NOTE: The color on the screw may not be the same as the image, but will still function the same.

Hoses are the most likely cause of clothes washer leaks. This tub-to-pump hose carries the water from the tub to the drain pump. If you notice that your tub is leaking during the wash cycle, check the the hose for holes. If the tube does have a hole or crack in it, the part should be replaced. Also, check both the connection and the junct...Read moreure of the hose with the drain for your house. While you are looking at the hose, check to see if the threads or clamps are corroded or loose. This OEM replacement pump hose is 20 inches long, and fits most clothes washer units. Remember to turn off the water supply and disconnect the power from your washer before you begin this repair.