8902 - Parts

Store the electrical energy needed by a microwaves high-voltage heating system with this replacement capacitor. During cooking, the capacitor works with the transformer, diode, and magnetron to help create the energy that heats food. A faulty capacitor may be linked to no heat, loud buzzing, or a fuse that blows when cooking begins. Howev...Read moreer, these signs can also come from other high-voltage components, so proper testing is important. Microwave capacitors may hold a deadly electrical charge even after the power cord is unplugged. For this reason, testing and installation must be completed by a qualified appliance service technician.

This OEM nut is a 5mm, gold, metal nut, which is sold individually. It can be installed with a Wrench or Socket and Torque Wrench by torquing to the manufacturer specifications. This nut is used to secure another part in place, and should be replaced if damaged due to fatigue (such as damaged threads or rounded ends). This nut can have v...Read morearious uses on various equipment, and as such the difficulty of the installation can vary, but generally this is an easy repair.

This breather, also known as a fuel tank vent, is a genuine OEM replacement part used in trimmers and edgers. It is responsible for managing the pressure and air flow inside the fuel system, by acting as a valve for the fuel tank. It allows clean air to enter the tank, while preventing dirt and debris from entering as well. Over time, the...Read more breather can crack or become clogged leading to restricted air flow, inconsistent fuel supply, fuel leakage, hard starting, and engine stalling. Locate the breather on or near the fuel tank and disconnect the hoses and fasteners attached to it. Depending on your model you may need to remove the fuel tank to complete this replacement. Place the new breather in position and reattach the hoses and fasteners. Test the new part by gently blowing into the breather to confirm that the air flow is not restricted.

This glass tray provides a stable, heat-resistant surface for cooking or heating while allowing even energy distribution. It is replaced when chipped, cracked, or missing to restore safe operation.

This fuel cap assembly is a genuine OEM part and is designed for use with outdoor handheld power equipment. Replacing your fuel cap is as simple as removing the old one and screwing the new cap on. This fuel cap keeps the fuel within the tank during operation, preventing leaks, and ensures that no dirt or debris enter the carburetor, filt...Read moreer, fuel lines or engine. Made of plastic with a cork seal underneath, this fuel cap is sold as an individual part, and has an approximately 2-inch diameter.

This individually sold fuel gasket is designed for use with handheld lawn and garden equipment and is the seal for the gas cap. This gasket is a genuine OEM part made of a composite material and will eventually become brittle because it interacts with gas and oil, meaning it will need replacing before it becomes debris in the fuel tank. T...Read morehis gasket not only prevents debris from entering the fuel tank, but it also prevents any leaks. To replace, simply unscrew your gas cap and remove the old gasket from the cap, and then replace it with the new.

The Recoil Starter Assembly, aka the Recoil Assembly, is a kit that includes the pulley, a return spring, the starter cord, and the pawls which engage the flywheel to turn over the engine. The components of this assembly are constructed of steel and plastic. The kit can be installed with a screwdriver and is rated as "Easy" to install...Read more (Tip: line all the parts up to install). This kit starts the engine, and you will know it is broken if the pull cord will not retract, or the engine is not engaging after it is pulled. The rope may also break. When the part breaks due to fatigue or general wear, it must be replaced. The part attaches on top of the engine where the flywheel is located.

This is a genuine replacement part that has been OEM sourced to ensure quality. The metal spring is intended to be used with trimmers from Shindaiwa and Echo. This spring is used within the cutting head to provide compression between the case and the spool housing. This item is sold as an individual part.

This OEM metal washer is commonly used on a variety of different small engine/lawn equipment models and is sold individually. This washer is used to help evenly distribute pressure from the securing bolt or screw with the cylinder cover, to reduce any effects of vibration from the engine. If the connection between the securing fastener be...Read morecomes loose, or if you are replacing the fastener itself, it is recommended that you replace this washer as well.

This is an authentic OEM sourced replacement part. The spring retainer is intended to be used with trimmers from Shindaiwa and Echo. The retainer is used to support the spool's compression spring within the cutting head assembly. This item may not require tools to install and is sold as an individual part.