8800 - Instructions

First I removed upper front grill by removing two Philips head screws on top and pulling off. This exposed the Philips head screw which holds control panel in place. After removing screw I pushed up on panel and it came off to expose fuse. With needle nose pliers I removed old fuse and again with pliers held new fuse in position. With th ... Read more e help of a bladed screwdriver, I pushed new fuse into holder, then replaced panel, screw and grill. This took less than 15 minutes even as one of the wires on control panel pulled out of connection and took some time to locate where to reconnect, otherwise was an easy fix
.

After ordering the element, found out it was the wrong element, I needed an 18.5 inch x 15.5 instead of the 15 1/4 x 15 1/2"...I slowly bent the element in shape to fit my oven. It works beautiful.
But for you guys, order the right one. Don't forget to measure your old elements spread from connection to connection. Install the new el ... Read more ement and then test to be sure it works proper.

Jenn-Air Microwave would not turn on. Clock worked , light worked, timer worked and would count down .I changed' Part #0813140 Switch, Micr} cost $8.99 plus shippingNow it works Thank You for good advise

First I removed the two screws that hold the element in place. Then I pulled the element out about 3 inches and disconnected the two wires. Reconnected the new wires, put the screws back in and the oven WORKED!!

I mistakenly thought I had to remove the microwave to get to the back, not so. I would have had access to what I needed to unscrew; but I have to admit the hassle of taking it down and putting it back equals having to work on it attached to the shelf-your call on how you do this. I unscrewed the front top to remove the vent piece that ... Read more is across the top front of the microwave. This will reveal the control panel screw. (While you have the vent removed you might want to clean the vent and the exposed filter.) carefully lift and pull out control panel. I unplugged a piece as the wires were tied tight. It will not completely detach, so carefully tip it back from exposed insides. The fuse is not clear but white with silver ends so look in upper right for it. I popped it out and replaced it. Replugged the wired part to cover and carefully fit tabs in and slide down to secre. Replace screw, replace vent piece and secure screws on top of microwave. I plugged it in to test before putting it back above my stove.

Removed 4 small star head screws from back of microwave, lifted body off, removed blown fuse and replaced with new one (found where cord enters). This model is stainless inside and out and I like it a lot. It is also sold by Daewoo and a few other manufacturers.

I didn't. Don't know how to get to light bulb to change it for this specific model

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

Our oven is a wall mounted oven so I could not reach the plugin. Therefore I shut the power off at our breaker box. I then removed the screws that held the old heating element to the oven. Removed the element, slipped connecting wires off of the old element. Next I slipped the connector wires onto the new element and replaced the scre ... Read more ws. Turned the power back and and checked to see if oven worked. It did! As you can tell I am a novice at home repair but this worked perfectly!

The cost of new ovens and a having an electrician come out to fix was ridiculous.We looked online fro an alternative and found your part w/ picture (which helped) for only 41.00 w/ tax to fix! We recieved item within 4 days and we fixed it in about 15 min. Thank you so much for saving us tons of money and loads of headache!

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

It was very easy,it took five minutes to replace it. I disconnected the two leeds from old burner and connected them to the new one.

Access is via RT. SIDE Panel as you face microwave. There are three screws on the bottom right edge to loosen. After that the side panel slips down and off. the fuse is located in the rear near where the power cord comes in. It is the white ceramic tube 1/4" in dia. and 1-1/2" long. Pull it out like any fuse and replace with new one. ... Read more Reassemble and you are done!

On the Saturday before Christmas, during some baking, my heating element we out of my oven! Since I was cooking Christmas dinner at my house on Thursday, I freaked out. Fortunately, we got on the interenet, ordered a new element, paid for 2-3 day shipping, and received it on Wed. afternoon. My husband unscrewed the old element, and pu ... Read more t the new one in about 5 minutes. Very easy job, and Christmas was a total success!

Repairmen all wanted a pretty penny to fix the problem, basically buying a new oven would have been cheaper. I ordered the heating element I needed. Once it arrived I took it out of the box and handed it and screw driver to my Son-in-law and as he stood there with a dumb founded look I told him “replace the old with the new one or I will ... Read more never cook for you again”. Boy did he do the work in a flash, it was easy peasy. I didn’t even break a sweat. I hope this is helpful to your other customers.