8635 - Instructions

I removed the two screws holding the access panel, and removed the access panel. Then removed the lower air duct. I then checked the burner, The solenoid was not opeing the valve for the gas. I order the coils, in two day I had the coils and installed them. The dryer is working great.

Unscrewed 4 screws,pulled off front of machine.Unscrewed 2 screws holding coils on,unplugged coils,installed new coils,plugged in coils,reinstalled 2 screws for hold down brace.Reinstalled front cover,plugged dryer into outlet(remember to unplugged dryer before working on it).started up,instant heat,works great.thanks Partselect for helpi ... Read more ng me out!!!

First, I inserted a screwdriver between the front panel and the top and popped the top loose. Next, there is a screw close to the top of the front panel on each side. Remove these. Next I unplugged the light switch from the front panel and removed the panel. Next, unscrew the gas line from the burner assy. and remove the screw holding ... Read more the burner assy. to the frame. CAREFULLY, remove the burner assy. taking care not to break the ceramic igniter. Remove the assembly and unscrew the brass screw on the right side of the burner. Replace the screw with the new assembly furnished with the conversion kit. Remove the tube that directs the gas to the ducting. Unscrew the orifice fitting and replace with the new fittings furnished with the kit. Reinstall the tube and CAREFULLY return the burner assembly to the dryer. Screw the assy to the frame and re-connect the gas line. Replace the front panel, 2 screws, and snap the top back down onto the front panel, taking care to align the two guide pins. Connect the gas line to the dryer and install the ducting. Plug it in and test for leaks.

The top was hard to figure out but I found that it pops off at the front with a flat screw driver. Be careful not to scratch the paint. I found that a rear drum roller was bad and the drum seals were deteriorated. I ordered a new belt, roller kit, front, and rear seals. This way I hoped I will not have to take it apart again. The seal wer ... Read more e the hardest parts to replace. Make sure you look and remember how they were on before removing them. The directions were not to clear on the seals. The rest were good. It is much better to do it once. Take a picture if possible, it might come in handy as I took mine apart a week or so before the parts came in. I also cleaned out all of the accumulated lint buildup with a shop-vac, including the vent pipe, heater area, and front door. When I was done with this it worked like brand new.

Checked four thermocouples all showed continuity with my multimeter so they were all good. I'd read that the coils commonly went out and that these were the symptoms. Hey, it's very simple in there. Not much else could be wrong. I had a Maytag repairman come out. At first he said the problem was a blocked vent. I knew he was wrong. Then h ... Read more e said one of the thermocouples went out. It was $80 for him to come out. It turned out that his second diagnosis was wrong too. To repair the dryer by Maytag would have cost me $240. I gave him $80 and bought the coils for $37. They are EXTREMELY easy to replace: two screws held a bracket that held two coils. With the bracket off, I took off the old coils and slid on the new ones.

My wife's dryer started squeaking very high pitched, intermittently and then continuously when running. It progressed to a loud shrieking, unbearable throughout the house. Make sure you unplug the dryer. First I replaced the Drum glide and cushion kit. This was easy to do. Pry open the top of the dryer open with a screwdrive or putty kni ... Read more fe. Now reach in and remove the retaining screws holding the front panel against the side panels. After releasing the front panel, let it fall forward about 4 inches and then unplug the two wire connected to the door closed sensor. Now carefully slide the thin belt towards the back of the dryer, it will release eventually as it is pulled off the pulley (dont worry, getting it back on is not that hard). Now you can remove the drum. After removing the drum, there are two tan or bluse plastic drum glides that the fron of the drum rests on. They can be worn out along with the cushion beneath them. Replace them with new one. This actually did NOT fix the problem. I put everything back together and....SQUEAK!! Next I undid everything as before and removed the drum. Now I decided to lubricate the rear rollers. First I used a silicone lubricant that again did not fix the problem. I could not find hi-temp lubricant, so I decided to use Axle grease. Bingo...no more squeak. To lubricate the rollers, remove the retaining clip and pull the wheel off. I put an even thin coat on the post they rest on and the inside hole of the wheel. Replace them and remember to put the retaining clip back on. Now replace the belt onto the metal pulley first, with the threaded side of the belt down towards the drive shaft, it should loop around the drive shaft and then you can pull it around the drum, slowly feedingthe drum farther and pulling the belt back along the drom. The smooth side of the belt should be on top of the drum. Now you have to reach back under the drum on the bottom right corner below the lint trap and pull the belt over the tensioner. Sounds harder than it is. Volia...that should fix it. Its been 3 days of non-stop laundry since the repair and no squeak. Next time I will purchase the replacement roller package, but this worked for now. Good luck.

Getting to any of the parts in the Maytag dryer is easy. Tip the dryer back and slide a 4 x 4 block under the front edge. You remove the whole front panel after you remove two screws at the bottom corners of the front panel. You need to tip the dryer back to get a screwdriver on the screws. Swing the front panel up to release the top of t ... Read more he door panel from the top. Watch the short wires to the door switch. Unhook the door switch wires and move the front panel out of the way. The timer on the top is accessed by re-moving two screws along the top edge. There are four screws. Remove them all and tip the top of the front panel forward. You then see that two screws hold the panel and the other two screws just hold the trim.

The dryer started normal. The drum motor run when the start button was operated. The fluff cycle operated normal to indicate the timer motor was OK. On the dry cycles, the igniter heated up. The gas came on. The dryer run for some period of time and then the flame went off. The thought was that the low temp cycle thermostat sensed the dryer was hot and thus switched over to time the cycle to its end. However, the low temp cycle thermostat tested good with a meter when the sensor was removed from the dryer and heated with a light bulb. Burnt contacts in the sensor were a possible problem. I also though the radiant sensor may be bad and not recycling after it got hot. After time, the igniter would cycle on but the gas flame would not come on. I thought the radiant heater might not be tripping the secondary coil on the gas valve. The gas valve coils tested good. I was checking them cold after the dryer had cooled down. I ordered a number of parts.

I got lucky and did a test on the coils while the dryer was still hot. One of the coils in the dual booster holding coil was going open when hot. When cold it had enough continuity to let the gas valve cycle on once. After the coil got warm it went open and shut the gas valve off. When the coil did cool off, it again had continuity. I was about ready to trash the dryer when I finely found the problem. I am happy I persisted and worked the problem through to a solution. I purchased several extra sensors but saved money in the long-run. I rate this problem at the high end of complexity for the do-it your self home owner to solve. The problem was an easy fix once the real problem was found. Only 4 screws and 3 push on wire connectors (two were on the front panel for the door switch).

This was so much easier than I though it was going to be. Pulled up on the top part of the dryer and folded it over to the back. Removed 2 screws for the front panel and disconnected some wires. Laying down I fed the new belt on and made sure the tensioner was put back into the right spot, because when the belt broke the tensioner spru ... Read more ng to the other end of its travel. Put everything back together. This was made super easy because you guys had the parts and the shipping was super fast. Alot of the local shops in the area didnt even carry the belt or were not helpful..

i looked byhind the freezer , the mottor has the relay connected to it.i took out the relay, and i descovery something was loose inside, i decided to take to check out at sears to see if they have in stock that especific relay. they did not have, they could order, that's when i dicided to go ahead and looking for in the internet, good i f ... Read more ound PARTSELECT,they had the part and i was very nice attended,they sent in 2 days i had fix my freezer. thanks PARTSELECT. gilmar couto.

Like another post, the start relay rattled like a baby rattle. Replaced the start relay and freezer works great.

The site offers a video for this part which worked perfectly. In addition to replacing the part, since the cardboard panel was off, we also cleaned all the dust off of the coils which someone recommended to do annually.

First I disconnected the power cord. Next the top of the dryer was easily popped upen with a screw driver by inserting it between the top panel and the front door panel. I removed the two sheet metal screws that held the door panel on the upper right and left sides. The door panel was easily lifted up and out and set it to the side (the d ... Read more oor switch can stay connected, the wire is long enough). d I pulled the drum out from off of the rollers that hold the drum in place. No need to remove the belt, it stays in place. I reached through the drum and removed the two hex-head screws that held the roller in place ( I only replaced the left one) and added the new one. I pushed the drum back in place over the rollers (it snaps in place). I propped the drum up with a short screw driver to raise it off of the right and left drum glides (on the bottom). I replaced the felt pads and the plastic glides and set the drum back in place. I also replaced the felt ring (seal) that circles the door opening that the drum also glides on. I glued it in place in spots (with gasket glue). It folds back over itself and forms a double thick pad. You will see what I mean when you see how the old one looks. I replaced the front door panel and snapped the top panel back in place. I let the dryer set over night so the glue would set up. I turned it on the next morning and it is as quiet now as when it was new. Oh ...Jay (the husband) did the work not Jean the wife (her dryer, her credit card)

I suspected a faulty igniter and disconnected the cable to the igniter and measured the resistance of the igniter and found it to be 70 ohms then I checked the voltage at the same cable towards the power source and found it to be 25 volts ac which should be 120 volts ac. Next I checked the radiant flame sensor and found it to be open (i ... Read more t should be a closed circuit when cold). I removed the flame sensor (with the power off) using a small box wrench and found a broken lead. Replacing the flame sensor solved the problem.

used a flat blade screw driver to open top up(like a car hood) then removed two screws that held the front panel on. Two more screws held the lint colector part in place. The only problem that I had was that I had to use Elmers white glue to hold the gasket that ran around the lint colector in place.Just a little dab, not enough to soak i ... Read more t.When I took the part out there was about a volleyball's worth of lint in the fan blower. Ordered the part and 2 or three days later I had it. If I need another part I will be back...

I needed to remove the front lower cover, very easy as it is held on with clips only so I used a flat head screw driver to pop it off. I had to remove the lint filter and then there are two screws attaching the top cover of the dryer to the internal lint filter tray. The top of the dryer can then be opened front to back I again used the ... Read more flat head screw driver to pop the top open as it has two clips at the front corners. It helps to have someone to hold it open or a rod of some type to keep it open. You can now lay the belt on the top of the drum and work it down the back side by pulling forward on the drum itself to seperate the drum from the seal that presses aginst the back side of the drum. I then went from the lower front to retrieve the belt now draped over the drum and pinched the belt to pass it through the tensioner and over the drive pulley. looking at it from the front the belt will come down the right side of the drum under the tensioner pulley around the drive pulley across the bottom of the drum and up the left side. The belt sits almost in the middle of the drum not against the back lip where there is a groove that might be confused as a place for the belt to ride that is where the seal sits then reverse the process to reattach the top to lint tunnel and reattach front cover and you are good to go . i would suggest vaccuming any old dust/ lint whlie everything is open as this reduces the chance for catching on fire I was supprised as to how much lint was loose inside the dryer cavity itself and our dryer is gas and the flame is an open flame.