8635 - Instructions

Removed control panel, discharged HV capacitor. Removed old diode, tested to confirm failure. Replaced part. Other than the removal of the panel swapping the part was almost as easy as replacing a light bulb.

I unplugged electrical cord to the freezer. I removed the cover to the relay and load protector. I labeled the wires and made a diagram on the proper placement of each wire going to the relay. I unplugged each wire and removed the relay. Then I removed the load protector. I installed the new load protector and new relay. I placed the wire ... Read more s on the proper terminals of the relay. I replaced the electrical cover to the relay and load protector. I plugged the electrical cord back in the electrical outlet. My freezer started working again. I placed several bottles of water in the freezer to make sure the freezer was working properly before I restocked it with food.

Thanks again for the help. You just saved me about $400.

I just inserted the door catch, which by the way fit in perfectly. Thanks. Took 5 seconds to repair.

I removed the 2 screws that hold the ignighter & cover in place...unpluged the wire...replaced it with the new ignighter...thats when I found out that it was easier to take off than to put on...but I got it back into place...replaced the 2 screws...put the new belt on the drum...fitted it around the moter...pulled the wheel spring back to ... Read more get it on tight...made sure the drum was fitted around the wheels...checked the tension...plugged in the wire for the ignighter...tested to see if the ignighter glowed...it did...I but the door back on the dryer...and it works...i thank my father for showing me how to work on machines...instead of letting me play with my dolls...thank you Parts select for getting my order to me in great condition & record time...

I opened up the dryer as per the instructions I had received from PartSelect tech support. It was very easy to do. The only unexpected thing was that the original belt had snapped and in doing so the idler pulley was actually laying on the floor of the dryer's bottom. I had to figure out how it went, but that only took a minute and I p ... Read more opped it back into place. I held the drum by hand while pulling the dryer face away so it wouldn't fall and then I slipped the belt over the drum and quickly closed the front up again. I aligned the belt on the spot where the old one had been, pulled it through the idler pulley and over the motor and voila. Done. I closed up the dryer and was on to another "Honey Do" project within 20 minutes.

First off, the parts were exactly what I needed and arrived at my front door in less than 48 hours.
The repair was quite easy. 1. access the "guts" by popping the two clipps and open top panel like a car hood.2. remove the high temp doohickie with a nut driver, one screw, two wires.3. Remove the heating element from its mount. 4. rem ... Read more ove the high temp fuse doohickie, By popping off its wires and little retaining bracket. 5. do steps (in this order) 5-1 replacing new parts. 6. spend three hours looking for the dryer brush, you know you have somewhere, to clean 5 years of accumulated lint out of the lint trap.7. drive to Ace, by dryer brush. 8. (most important step) clean the lint trap, or be forced to repeat steps 1-5. 9. Pop a cold one and relish the peace and quiet, devoid of spousal nagging to fix the damn dryer. 10. Take down clothesline in backyard.

unplugged, removed old parts, replaced with new

This was a simple job. Raised the flap in the back that houses the compressor, removed the wire that holds the relay, pulled out the old relay and pushed the new one on. Replaced wire holder and that was it. Plugged it frig and freezer is at zero and lower compartment at 35. As easy as brushing your teeth!

Opened front panel .Tested both coils on gas valve.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.

I located the part that was the culprit as it had buzzed very much before quitting. This is an easy removal as the part is in a two prong jack and just needs to be carefully removed with the new part inserted back in the jack provided. The refrigerator works fine now, but the run capacitor will still buzz on start up of the compressor. I ... Read more do hope this is normal in this model? anyway it runs fine mow. Thank you.

I used a small screwdriver to disconnect wires from old starter. I connected the overload and starter, two wires. I put the unit back in the keeper, plugged the unit in, turned up the thermostat and it's working beautifully.

Very easy repair. Just needed to remove some screws to access the heating element area. The fuses are (1) just above the elements and (2) to the right side of them (if facing from the front). Alittle loosening with a philips screwdriver, removing blown fuses, replace with new fuses, tighten new fuses in place, replace outer screws and ... Read more job done. Also made sure to fully clean lint collection area. I had a good amount stuck in there and it restricted air flow which caused the fuses to blow. It took 6 years worth of drying to make it happen.

Took out two front Panel screws and removed the panel. Removed Gas solenoid coil holding bracket by removing two phillips head screws. Disconnected the coil leads. and removed the coils. Connected the new coils to the leads and set in place. Replaced the holding bracket and the two screws. Replaced the front cover and the two front ... Read more cover screws. Piece of Cake!

I lifted the top of the dryer cabinet, like the hood of a car using a screwdriver to pry it open. I removed the two screws in the upper right corner of the cabinet front. I disconnected the safty switch on the front door. The front of the cabinet can then be removed by lifting up the front off the pins in the base. With the drum expo ... Read more sed you can place the belt on and thread it through the two pulleys on the motor. Consult the diagrams provided on the PartsSelect website for the proper positioning of the belt on the pulleys. After the belt is installed spin the drum by hand one turn to make sure that it is seated properly on the drum and pulleys. Reassemble the dryer in the reverve order.

After replaceing several parts including the thermostats the last part I replaced the coils were the defective part. I originally metered out the themostats and they appeared to be okay but since this was my first time I thought I might have been mistaken. It turns out the last part I thought it could be was the part that was defective. I ... Read more will say that it is very simple to replace any of the parts involved. The hardest part was trying to open the dryer itself. But after having to do it 3 times, I'm now a pro. I also replaced the drum belt and since I had it open I also replaced the belf idler with a newer modified idler rolller.

Putting the belt back on is easy, but it helps to view the video or a picture to understand how the belt goes around it.