84190 Kenmore Microwave - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
During cycle, thump type of noise. Drum stopped spinning
0 of 1 people
found this instruction helpful.
-
Mark from Justice, IL
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
Looked through the acces panel, drive belt broke.
Replaced belt with new one. At the same time vaccumed all lint and debris from the compartment.
Replaced belt with new one. At the same time vaccumed all lint and debris from the compartment.
Was this helpful?
Thank you for voting!
Tumbler Would Not Spin / Needed Belt
0 of 1 people
found this instruction helpful.
-
JAIME from SEGUIN, TX
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
It was very obvious that it was the belt. You could hear the motor and it would even generate heat. But the tumbler would not turn. Well there was even directions on this site to do what needed to be done. It was simple and easy. Plus it gave me a chance to clean alot of dust that had accumulated behind the dryer. After shipping of
... Read more
the belt, I was just under $19. 00. Thank you for the simplicity of this website.
Read less
Was this helpful?
Thank you for voting!
Dryer would not tumble.
0 of 1 people
found this instruction helpful.
-
Joyce from Springfield, IL
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Replaced the belt drive. Dryer works now.
Was this helpful?
Thank you for voting!
dryer drum not turning
0 of 1 people
found this instruction helpful.
-
Jeff from Waterloo, IA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Wrench set
open lid,release spring clips holding it down..undo 2 screws holding front cover,lift up and out of the way. grab drum and pull forward until its free of back rollers, remove old belt, put new belt around drum..rib side down place drum back in place loosely..put belt on motor shaft,rib side down.reach in with right arm and lift tension pu
... Read more
lley , place pulley on top of belt, push drum back onto rear rollers until its seated, reassemble and let it rip
Read less
Was this helpful?
Thank you for voting!
The dryer belt broke from old age.
0 of 1 people
found this instruction helpful.
-
David from Mayville, NY
- Really Easy
- 30 - 60 mins
-
Nutdriver
Practically disassembled the entire dryer to find out the belt goes on from the front of the machine. That discovered I ordered the part from PartSelect, It came in no time at all and as soon as I got the part I got to work and it went on without any trouble. I just had to figure out, and clean up, and lubricate the tention pulley and rem
... Read more
ount it to the floor housing of the dryer and reassemble. OH! I forgot to reassemble a few wires as I was aimlessly disasembling in the back so I had to find out the hard way the dryer heat didn't work,..but just remove the rear pannel and reconnect the wires and were good to go!! Now I'm in good terms with my wife again! I like that part the most!
Read less
Was this helpful?
Thank you for voting!
Dryer was not tumbling.
0 of 1 people
found this instruction helpful.
-
Helen from Annandale, VA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
My son-in-law did the repair. He had just experienced the same problem with their dryer that he fixed. I think it was relatively easy but he did have to lay down on the floor to put the new belt on which I could not have done because of my arthritis. We just had trouble with one of the screws to connect the front of the dryer to the rest
... Read more
of the dryer. A screw size-adjustment-plate fell to the bottom when I unscrewed the screw and we didn't know what we were looking for until he found it and then I figured out how it had to go on because the holes were too big for the screw.
Read less
Was this helpful?
Thank you for voting!
Dryer tumbler would not spin
0 of 1 people
found this instruction helpful.
-
Sam from Aurora, IL
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
There was a video that showed exactly how to replace the belt which was awesome. First remove the screen filter and the two screws. Use puddy knife to release the top by inserting under the top about an inch or two from the front edge on the left and right side in front. The top should release and lift up. Secure the top so it does not
... Read more
fall forward or backwards. There are two screws about a third way down from the inside that you can see from the top. Remove them and the front panel will lift slighly and lay down. Remove the drum or just install the new belt around the drum as specified. Replae the tension pully as well as this usually is the reason the belt breaks. Reinstall and you're back in business. I recommend watching the video on how to replace the belt.
Read less
Was this helpful?
Thank you for voting!
Broken drive belt
0 of 1 people
found this instruction helpful.
-
Robert from Deland, FL
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
Disassembled dryer per video instructions. MOdified tension roller assembly by securing it to bottom of dryer. Drilled hole next to bracket and mounted metal clamp with a self tapping screw. It was much easier to install the belt if the tension assembly was stabilized.
Was this helpful?
Thank you for voting!
dryer stopped tumbling
0 of 1 people
found this instruction helpful.
-
Kate from Freehold, NJ
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
Took off the front of the dryer & replaced belt- it was a lot easier than I thought. Taking the front off was the hardest part.
Was this helpful?
Thank you for voting!
Belt broken on dryer
0 of 1 people
found this instruction helpful.
-
Patricia from Cicero, IN
- Really Easy
- 30 - 60 mins
-
Screw drivers
My son told me about your site. My dryer needed a belt replaced so I ordered it on one day and it was here the next day. I watched the video on how to replace a belt, Done just what they said to do and it was so easy. No problems at all only took about 45 minutes. And let me say this I am a woman, so if I can do it, anybody can do it.
... Read more
Thank you so much for a wonderful site! P.M
Read less
Was this helpful?
Thank you for voting!
Dryer belt was broken
0 of 1 people
found this instruction helpful.
-
Gary from Ludington, MI
- Really Easy
- 30 - 60 mins
Just followed the directions that came with the belt and it went on perfectly.
Was this helpful?
Thank you for voting!
Broken Belt
0 of 1 people
found this instruction helpful.
-
Andrew from Kimberling City, MO
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Repair was straight forward and repair video on PartSelect.com was excellent. Price was reasonable and shipping was prompt. I will use PartSelect.com again.
Was this helpful?
Thank you for voting!
Broken belt
0 of 1 people
found this instruction helpful.
-
Kathleen from Carneys Point, NJ
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
As per instructions. Removed top and front cover. Then installed new belt and gave the unit a good cleaning before reassembly.
Was this helpful?
Thank you for voting!
Dryer barrel stopped turning
0 of 1 people
found this instruction helpful.
-
Robert from Rubicon, WI
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I disconnected the electricty. I openned the top of the dryer. I unscrewed the front and took it off. I removed the old broken belt. I slipped the new belt on. I threaded it thru the idler and over the motor pully, I put the front back on. I reseated the rear seal of the barrel. I closed the top, reconnected the vent hose, and plu
... Read more
gged it in. Turned it on, and it worked.
Read less
Was this helpful?
Thank you for voting!
broken belt - drum would not turn
0 of 1 people
found this instruction helpful.
-
Charles from Rockport, MA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
took the top and front off of the appliance. Followed the instructions and picture included to put on the new belt and reassembled the machine. Great prompt service in sending the needed part to me.
Was this helpful?
Thank you for voting!