EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

84190 Kenmore Microwave - Overview

Diagrams for 84190

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Multi Rib Belt - 92-1/4" – Part Number: 341241
$15.00
In Stock
Multi Rib Belt - 92-1/4"
★★★★★
★★★★★
(433)
Part #341241
This dryer drum belt (Whirlpool Dryer Belt, Drive Belt) has four ridges, three grooves and is 1/4" wide, and 92 1/4 inches in length. It comes in black and is made of rubber. The belt transfers the rotation of the motor to turn the drum. The belt attaches to the drum, idler pulley, and motor pulley.
KNOB – Part Number: 2009
No Longer Available
KNOB
Part #2009
SCREW – Part Number: 2005
$2799.62
Special Order
SCREW
Part #2005
BALL – Part Number: 2007
No Longer Available
BALL
Part #2007
SHOULDER – Part Number: 2003
$1703.87
Special Order
SHOULDER
Part #2003
SHOULDER – Part Number: 2004
$323.79
Special Order
SHOULDER
Part #2004
RADIANT PLATE 350X350X30 MM – Part Number: 2009
$333.48
Special Order
Tank W/Gage – Part Number: 2006
No Longer Available
Tank W/Gage
Part #2006
Top duct – Part Number: 2000
No Longer Available
Top duct
Part #2000
Duct bracket – Part Number: 2001
No Longer Available
Duct bracket
Part #2001
Screw – Part Number: 2002
No Longer Available
Screw
Part #2002

Common Symptoms of the 84190

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
broken tumbler belt
145 of 165 people found this instruction helpful.
  • Michael from San Antonio, TX
  • Easy
  • 30 - 60 mins
  • Screw drivers, Wrench set
1. Removed the screws from the lint catcher
2. Removed the bolts from upper rear of dryer
3. Pried off the dryer top from the front (it rests on rear hinges)
4. Disconnected dryer door wiring
5. Removed bolt from inside upper front corners; removed front panel (be careful: the edges are sharp and the tumbler will fall when it loses support)
6. Removed broken belt and lint from interior parts; removed tensioner (which had fallen out of place). Note: The newer models have a tensioner pulley; my older model had a smooth semicircle that was confusing at first glance
7. Flipped dryer onto its back (for easier reinsertion of new belt and tumbler)
8. Placed new belt on tumbler; reinserted tumbler
9. Inserted new belt through tensioner, inserted tensioner "legs" into grooves on floor. Note: The belt will pull the tensioner upright when it's inserted properly (which isn't obvious at first)
10. Made sure belt and tumbler seal were properly installed
11. Replaced parts in reverse order
The process took over an hour because I couldn't figure out how to insert the belt through the tensioner. The trick is to insert the folded belt through the tensioner and onto the motor pulley. If I had to do it again, it would take about 30 minutes (including cleaning lint)
Was this helpful?
Thank you for voting!
Broken belt - drum would not turn
87 of 101 people found this instruction helpful.
  • Gary from Oakland, MD
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Started out taking the back off, then found online that access is from the front and much easier to get to. Simply pop the hinges in the back of the top panel and then the front of the top is popped off. From there, it is easy to remove the old belt, clean the innards (found 31 cents) and replace the new belt. It was a little disconcer ting to see the idler pulley laying loose inside, but the diagram showed exactly how to put it back in place, with the new belt keeping it in place.
Was this helpful?
Thank you for voting!
dryer drum wouldn't turn
36 of 40 people found this instruction helpful.
  • Steve from Peachtree City, GA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
First of all, you go in from the front. There a clip on each side that I just pried up to pop the front of the dryer up. A screw also needs to be removed in the lint catcher area. Also, two screws holding the door open switch must be removed as I never could get the electrical connectors to disconnect. No big deal. I had to figure ou t you must lift the front of the dryer up as the last two things holding it in are a prong on each side. Lift the front up and off and set it aside. As you do this the drum will either fall on your feet or you'll have it supported be another person or with something else. I used bungee cords and kept it in the laundry room. Cleaned out all the old lint, collected a few bucks in change. It took me awhile to figure out how the new belt routed through the removable pulley guide thing and around the wheel pulley. I don't remember right now as I'm not looking at it but remember pinching the belt and feeding it through the guide and around the wheel pulley which has a little slot and grooves matching the belt. Besides scrapping my wife's hand while she was helping me get the front of the dryer back on there were no casualties or further complications. Good luck!
Was this helpful?
Thank you for voting!