EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

84190 Kenmore Microwave - Instructions

All Instructions for the 84190
91 - 105 of 396

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bad Belt
1 of 3 people found this instruction helpful.
  • DANIEL from PAXTON, IL
  • Easy
  • 30 - 60 mins
  • Screw drivers
Removed front . Slip belt over drum
Was this helpful?
Thank you for voting!
broken multi rib belt
1 of 3 people found this instruction helpful.
  • George from Pittsfield, ME
  • Easy
  • 30 - 60 mins
  • Screw drivers
Lifted top cover (hinged) , removed 2 screws to remove front panel, sliped new belt over drum, lifting drum slightly from front bearings.Using a small mirror taped to a stick and a good tube florescent drop light, was able to place new belt on drive pulley and under tensioner pulley. Rotated drum manually to make sure proper placement of belt.
Was this helpful?
Thank you for voting!
my dryer belt broke that turns the clothes to get them dry
0 of 1 people found this instruction helpful.
  • Teresa from Marshall, NC
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
First, we pulled the dryer out and unplugged it from the wall. Then, we opened the top of the dryer,and we could lift the broken belt right up off the round tub. We unscrewed the screws that hold the front of the dryer on, they are inside the front panel. We had to remove the sensor switch for the door so we could move the whole front pe ice out of the way. Then we worked the belt around the tub and back to the pulley then we put the door back on and the door sensor, and closed the top . Finally, we pushed the dryer back and plugged it back up and it was fixed. This was not a hard repair at all. We vacumed all the lint out while we were inside the dryer. That was a bit messy but worth it.
Was this helpful?
Thank you for voting!
noisy drum rotation
0 of 1 people found this instruction helpful.
  • TOM from SAMMAMISH, WA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
problem removing cabinet because of funny clips used. Put back together using sheet metal screws so will not be problem next time. Belt replacement easy once acess was gained.
Was this helpful?
Thank you for voting!
Broken Dryer Belt
0 of 1 people found this instruction helpful.
  • Paul from Harrisburg, PA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Just as many others have stated, replacing the belt was an easy job. First, unplug the power cord. Remove the 2 screws from the filter housing, pop the two tabs near the corners (I used a fairly large flat-head screw driver) and lift the top. Remove the two fasteners holding the front panel to the side panels. I used a 5/16th socket with a ¼ inch driver. You’ll want to secure the drum as it will fall out when you remove the front panel. I used a bungee cord and hooked it through an opening in the drum and the other end I secured to an overhead pipe. The drum is not heavy so it was no big deal. You will also have to unclip a small wiring harness before lifting the front panel. There are also 2 tabs, one on each side, on the front panel near the bottom. Once I got the front off, I removed the drum so I could vacuum out all the lint. In addition to the belt, I ordered two rollers and a new idler pulley but when I inspected my unit, the rollers and pulley were still in good shape so I now have the parts for when I’ll need them.

I then routed the belt around the drum and placed the drum back in the unit and again secured it with the bungee cord to hold it as I positioned the belt to track the same as the marks left from the old belt. The directions I received with the new belt were easy to understand but it still took me a minute or two to properly route the belt through the idler pulley and onto the motor pulley.

Once I had the belt installed I asked my wife to help hold the drum while I spun it with my hands to make sure the belt tracked correctly and the rear of the drum was sealed. Her help was not necessary but made it a little easier for me. Then I bungeed it back up, installed the front panel, securing the bolts on both sides. Don’t forget to plug the small wiring harness back together as the dryer will not run if you do not. I did another quick test by turning the drum with my hands and all was good. Next, close the top of the unit, securing the tabs you popped open, reinstall the screws in the filter housing and plug in the unit and test. All in all it’s a very easy job. Not sure what a service call would cost but I know it would be a lot more than I spent.

This is my second experience with Parts Select and they will get my business whenever I need parts. I quickly had my shipment tracking number and the parts were delivered quickly. I ordered on a Monday and the package was at my door when I got home from work on Wednesday.
Was this helpful?
Thank you for voting!
Dryer wouldn't spin
0 of 1 people found this instruction helpful.
  • Lee from North Billerica, MA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I read the stories on Partselect and opened popped the top, removed the front and observed the broken belt. I ordered the belt and loaded it around the tub, with the ribs facing down and the blue side exposed. Then I got down on the floor and noticed that the pulley was laying on the floor which got me a bit nervous.

The thin g I struggled with for a few minutes was how to secure the pulley, which fit into a slot on the floor of the dryer. I needed to nose the front edge into the front opening and then snap the back into place. From there, the belt is fed underneath the pulley and snapped around the motor.
Was this helpful?
Thank you for voting!
belt broke
0 of 1 people found this instruction helpful.
  • SANDRA from ROCKY MOUNT, NC
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
took off the front panel of the dryer and then pulled
the drum out.. located the pulley and put belt around the pulley -- had a little trouble getting the
belt to stay around the pulley while we put the drum
back in - finally took a small flashlight and wedged it between the pulley and the vent and got the drum
in and put the front panel back on and it worked great
Was this helpful?
Thank you for voting!
snapped drive belt
0 of 1 people found this instruction helpful.
  • Brett from Northampton, MA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Not too difficult. Be sure to google directions first as I started in the wrong place. Getting the drum back in place was tricky. It was easier when I propped it up from the underside with a bottle
Was this helpful?
Thank you for voting!
Dryer belt broke
0 of 1 people found this instruction helpful.
  • Michael from Charleston, MS
  • Easy
  • 30 - 60 mins
  • Screw drivers
I followed instructions for getting the dryer open. The putty knife is used to release the latches that hold down the front of the dryer top. One on each side. Just slip the putty knife in and pull up at the same time. Disconnected the door switch. The broken belt was lying in there. On the PartSelect site, I identified the correct belt b y description and measuring. Then, I ordered the part. It came very quickly with just standard shipping.
Taking the advice of a previous post, we laid the dryer on its back, and slid the front of the cabinet up to release it. The idler was laying in the bottom..
I put the idler back according to the drawing with the instructions. Then, I put the belt around the top of the drum. My wife held it in place while I put the belt through the idler and around the motor shaft.
Once that was done, we just reassembled the dryer and turned it on. Eureka. It worked.
Was this helpful?
Thank you for voting!
Dryer belt broke
0 of 1 people found this instruction helpful.
  • Richard from Bel Air, MD
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Remove clothes from dryer.
Unplug power cord.
Pull the dryer a few inches away from the wall, don't pull too much to disturb the gas line.
Lift the dryer lint catch panel and remove the two screws with a straight blade screwdriver.
Remove the front lower access panel. Remove broken belt.
Using a screw driver, "pop " the two front corners and hinge back the dryer top enough that it doesn't come crashing down on your head or fingers.
Unplug the two wires to the electrical component to the right side front, one red, one white. Mark what went where. Slide the wire clip off its spot, allowing the wires to be moved clear of the front panel.
Using a 5/16" nut driver remove the two front screws. While holding the drum with your left hand, carefully lower the front panel enough to allow you to "fish" the belt between the drum and panel. There is enough room to allow this.
Once you have the belt fed down through and laying on top of the dryer drum. Reverse the directions.
Before connecting the belt tensioner, feed the belt around the drum to check that the belt is on correctly and not rolled.
Feed the belt through the tensioner and attach to the main drive pulley. Install the belt tensioner to its base slots. Again roll the drum by hand to make sure the belt is installed properly
Vacuum out any excessive lint and debris. Install the front lower access panel. Slide the dryer back into position, not kinking any gas lines.
Plug back in power cord, turn on for test. Done in 45 minutes.
Was this helpful?
Thank you for voting!
Broken Drum belt
0 of 1 people found this instruction helpful.
  • David from Alma, NE
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
1.removed the top of the dryer.
2. removed the wiring to the door switch.
3. removed the front of the dryer.
4. removed the broken belt .
5. removed the drum .
6. cleaned the inside of the housing so that it was free of dust, and dirt.
7. replaced the drum, making certain that the seals were rinding where they are suppose to.
8. placed new belt on drum, placed the belt through the tension pulley, and on to the motor.
9. I replaced the front of the machine, making sure that the front seal around the opening was in its proper place, and replace the screws with the use of a nutdriver.
10. I reconnected the wires to the door switch.
11. I rotated the drum by hand to make sure it runs freely and seals were operating properly.
12. Then I replaced the top of the dryer.
The job took about an hour to do, and was fairly easy from a diy person. The hardest part was looking for a place to buy the parts for replacement for such and old machine. I want to thank you for being out there.
Was this helpful?
Thank you for voting!
Dryer wouldn't tumble.
0 of 1 people found this instruction helpful.
  • Luis from Turnersville, NJ
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
First I removed the control lid which was held down by two screws. Then i removed thw two screws holding down lint trap. I lifted the top lid then had to remove the top two inner screws that hold the front panel up. Removed the front panel looked underneath the drum and i could see the pulley system. You were able to see the mark on the d rum from the old belt so that gave you a good indication of the positioning of the new belt. Then replaced all the screws and done a fairly easy job and you save yourself alot of money with the repairman.
Was this helpful?
Thank you for voting!
Dryer tub would not rotate
0 of 1 people found this instruction helpful.
  • Alexander from King of Prussia, PA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Originally, my wife was going to call a repair man to come replace the belt. I could not find the manual online since the dryer is at least 15 years, if not older. When I cut the belt and measured it, I did a search on Google and the Part Select website came up. I navigated to the belt and purchased it. Surprisingly, the belt was deli vered much quicker than promised, so I was pleased with that.

I did another search on how to replace the belt, and foud the following directions:

1. Remove the two screws holding the lint screen (my dryer has the lint screen on top, skip this step if the lint screen is in the door).

2. Use a putty knife to pop the plastic pins that hold the lid to the frame.

3. Use a socket or screwdriver to remove the two screws at the top corners of the front panel.

4. Lift the front panel to release the brackets that hold it in at the base.

5. Remove the front panel, put a brick or block of wood to support the drum.

6. Put the belt on, trying to get it in the grooves.

7. The idler pulley popped off when the original belt broke. The base of the pulley fits into some slots next to the motor. Loop the belt under the pulley and put the loop into the drive pulley on the motor. The idler pulley will then spring up and hold itself in place.

8. Make sure the front and rear gaskets (cloth, felt and plastic) are in place.

9. Repeat the above steps for putting everything back together, don't forget to remove the brick or wood block first!

Very easy project. Thank you Part Select for shipping the part so quickly - ordered on a Thursday, received on Saturday, even though I paid for the standard shipping!
Was this helpful?
Thank you for voting!
Dryer Tub stopped rotating
0 of 1 people found this instruction helpful.
  • John from Tolleson, AL
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
I used the online examples at your site, the repair was quick. The down and dirty

1. remove screws from lint filter
2. remove 2 top left / right screws from the back
3. pop open front top edge of dryer. remove the top
4. remove inside top front left / right screws
5. disconnect wireing from front door. I had to use a very small screw driver to get the wiring clip to seperate. Both sides of the electrical plactic connector have a clip notch.
6. lift front dryer door up from bottom clips. flip dryer on it's back as it works best if dryer is laid on it's back for better access.
7. place new belt around dryer tub rubber groved side towards the dryer tumbler.
8. feed the belt through the tension pully and around the electric drive motor.
9. make sure tension pully is secured / clipped back to the dryer floor. It helps to slowly rotate the dryer tumbler/ tub to reposition the belt.
10 carefully move dryer back to upright position. helps to have a second pair of hands as you will need to hold the tunbler / tub while you reposition the front door on the lower clips.
11. pug in electrical wireing, replace front, back and lent filter screws.

Additional Info: You might want to remove the dryer hose from the back of the dryer as it will make it easier when you lay the dryer on it's back.

My wife and I completed the repair in 30 to 60 minutes.
Was this helpful?
Thank you for voting!
Drum not spining
0 of 1 people found this instruction helpful.
  • kevin from san rafael, CA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
First remove 2 screws holding top on the rear of the dryer
Remove 2 screws under lint door
Tilt back dryer top
Remove 2 screws holding front of dryer to sides
Pull off wires to door switch
Pull up on front of dryer and remove
Pull out broken belt
Install new belt
Replace front, switch wires and top
Done
Was this helpful?
Thank you for voting!
All Instructions for the 84190
91 - 105 of 396