8361 - Instructions

Your site was easy to navigate, which made determining the problem from other customers easy, and choosing the correct part to replace the malfunctioning burner.

The malfunctioning burner was easy to remove by twisting it a quarter turn counter clockwise, removing the two wires and replacing it with the new burner cap with el ... Read more ectrode.

Used strap wrench to turn out. Rust build up under the burner. Used flat screwdriver to loosen under burner and strap wrench to turn out. Then replaceing the igniter was very easy.

Removed stove top to work bench'
Disassembled burners from enclosure to gain
access to spark module.
removed old module and disconnected slip on electrical connections
Installed four new slipon connectors to match new modual
attached newmodule to frame and connected wires.
Tested unit by pluging into electei ... Read more c outlet and turning burner dial to lite . Success
reassembled stove top and installed in kitchen.
job complete

Removed screws from back right of oven. Found spark module under right side panel of oven. Module connected in a slightly different way, so I had to drill a new hole and use a machine screw to secure it. All wires matched up exactly on new spark module. Replaced side panel, plugged it in and... SPARKS. Cheap and easy replacement and didn' ... Read more t have to call Maytag for repair!

Replaced the ignition module with one from PartSelect. took care of the problem. They had the part in stock. Great service. Got the part in four days.

I used the advise given in the website and it was very informative- the part was exactly where the folks on the website said it would be and although it wasnt the actual maytag part it was easily fitted by using the wire splices i mentioned and it was shipped quickly The whole process took less the 30 min once received. thank you for a v ... Read more ery useful site.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the six wires. Then I repeated those steps in back order. That's it

I replaced all the burner switches as well as the spark ignition module. It was necessary to solder small terminals to use the existing wires with the new spark ignition module. Otherwise, this was a pretty straightforward job. My wife, an excellent cook, is now even happier than usual.

Unscrew the bottom cover, remove the old ignitor. Reverse the process to install. Hardest part was getting the bottom cover screws out because of rust. Otherwise, very simple.

1. Apply gas pipe joint sealer to treaded nipple on bottom of cooktop; 2. Install regulator on nipple with regulator direction arrow pointing to top of cooktop; 3. Tighten but do not overtighten as it may crack the aluminum body regulator; 4. Make sure the face of the regulator with the green painted surface faces the outside of the cabin ... Read more et; 5. Get a new gas flex hose to connect to gas pipe (got mine at Lowe's - 2 feet long with all the right fittings for about $15). 6. Follow instructions on gas flex hose - make sure you use gas pipe joint sealer only where indicated; 7. Turn gas shutoff valve back on and test for leaks using soapy water; 8. Turn on each cooktop burner to bleed out air.

Removed burner pan screws,igniters, gas tubes & burners. Changed 2 igniters, removed rust & repainted ends of 2 of the tubes (heatproof paint). New burners were made a hair smaller than original but locked in O.K...Now, the hard part...disconnected all four tubes from gas valve assembly. (Had to shut off gas to house in order to remove ma ... Read more in gas line to stovetop.) Had to remove valve box in order to remove/replace frozen valve. Unit is 25 years old, works as and looks new...Rust was caused by boil-overs.

We replaced 3 of 4 igniters on the stove top according to the previously submitted recommendations. Easy to do butt after putting one of the modules back together, we found one igniter still didn't function. We discovered the solution was to run the connecting wire under the gas tubing. Apparently it was compressed when it was over the ... Read more top of the tube and not under it.

use the pliers. to get. the remaining half off and the screwdriver to cleen the rest of the rust off

I removed the old burner with pliers took off the electrodes. Replace the new burner attach the electrodes placed it back in the burner slot and now it works.

I have a Magic Chef gas stove, The top burner came off with ease, just a quarter turn then pull up to expose igniter. Only two wires to remove and two phillips head screws to remove to release igniter. I was done in 5 minutes.