8046 - Parts

The upper dishrack roller and axel kit comes with two pieces, a wheel and an axle. This kit is made for your dishwasher. Both pieces measure to be roughly one square inch each, they are made entirely of plastic, and are white in color. The purpose of these parts is to allow your dishrack to roll easily on the support rails. This kit is so...Read moreld individually and contains only one wheel and one axle. Please order the required quantity for your repair. If your dishrack is having trouble rolling in and out you may need replace your rollers and axles.

This door seal is for dishwashers. Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door. After installing the door seal, shut the dishwasher door and leave the door closed for several hours to properly seat the new door seal.

If your dishwasher is leaking or not draining properly, you may need to replace the drain hose. The drain hose connects to the pump located below the lower spray arm and aids in proper dishwasher drainage. This white and black plastic hose is 7.5 feet long. For this repair, you will need either a 1/4-inch or 5/16-inch nut driver, dependin...Read moreg on your model. You will need to remove the lower access panel on your dishwasher to complete this repair; it is often easier to remove the dishwasher from the cabinet to do so. Be sure to disconnect the dishwasher from both the power and water supply before completing this repair.

This dishwasher door latch assembly is a critical component designed to ensure safe and efficient operation. It features an integrated switch that functions as an on-off mechanism, preventing the appliance from running when the door is open. If your dishwasher fails to start or the door does not close or latch securely, replacing the latc...Read moreh assembly may resolve the issue. Installation requires disconnecting the power supply to avoid electrical hazards. This part is compatible with standard dishwasher models and is engineered for a secure fit and reliable performance.

This door spring is manufactured for a dishwasher door. The door spring applies tension to the dishwasher door so that the door does not drop too quickly when it is opening. If the door drops too quickly, it could cause damage to the dishwasher door or dishwasher door hinges. This spring is sold individually. Check the spring on the oppos...Read moreite side of the dishwasher door, they often wear at the same rate so you may want to replace both springs for exact tension on either side. No tools are required for this repair. This is an OEM replacement part.

This fold-down fence with clips is designed to help secure dishes in place during wash cycles in compatible Frigidaire dishwashers. Installed on the rack, it provides added support for smaller or lightweight items that may shift or tip over during cleaning. If dishes are no longer staying upright or are falling over, the fence may be worn...Read more or damaged and should be replaced. This part is sold individually and is sourced directly from the original manufacturer. Please verify compatibility with your specific model before purchase.

This is a part for your range. This switch controls the stovetop surface burner. If you notice that your stove top is not turning on or is not adjusting to the corresponding desired heat, it is mostly likely due to the burner switch needing to be replaced. You will need a #1 square-head screwdriver and needle-nose pliers. Disconnect the p...Read moreower from the range. You will need to move the range out from the wall to remove the upper back panel to access to this part. This is an OEM genuine part.

Terminal block kits are also known as terminal boards, or terminal strips, and they are found in a wide variety of household appliances. Most often in ranges, wall ovens, and dryers. This kit attaches the power cord to the inner wiring of your appliance. If the terminal block is faulty, your appliance will not get the power it needs to op...Read moreerate properly. When removing the old block pay close attention to the wire placement, this will make installing your new part much easier. If you notice any of the wires or wire terminals are corroded or damaged they will also need to be replaced.

This rail end cap, or dishrack stop clip, is a genuine OEM replacement part for your dishwasher. This part keeps the rack in your dishwasher from sliding out. This is a very easy repair, to complete it you only need a flat blade screwdriver. Use the screwdriver to pry the locking tab open on the cap, located at the front of your upper dishrack. Pull off the end cap and lock the new one into place.

This is a drain pump assembly for various compatible models of dishwashers, that is responsible for draining the water from the dishwasher after every cycle. This drain pump assembly is made of plastic and fits within the sump assembly, which controls the flow of water into the drain. This drain pump assembly is a genuine OEM part and is ...Read moremade of a high-quality plastic but is sold as an individual component without any other parts, like its drain pump check ball which works within the pump to prevent water from backwashing into the pump, as well as the drain pump cover. If you notice your dishwasher is not draining or has a lot of water buildup at the bottom of the sump assembly, this filter may be damaged, clogged or broken, and in need of a replacement. To replace this pump assembly, you will only need a Philips-head screwdriver, but should start by removing your dishwasher racks. Then, pull up on the lower spray arm, and drain trap to remove them. Next, rotate the spray arm support and pull that up to remove it, at which point you can remove the base and filter for the drain pump. With those out, you can use your Philips-head screwdriver to disconnect and remove the cover and drain pump assembly. With the pump removed, you can inspect it or install the new drain pump assembly, with the same hardware as before. Then it is as simple as reassembling the rest of your dishwasher, ensuring each connection point is fastened tightly.

This lower dishrack assembly is a genuine replacement component designed to restore full functionality to your dishwasher. Made from durable, rust-resistant materials, it securely holds dishes, cookware, and utensils in place during the wash cycle, ensuring optimal cleaning and preventing damage to both the items and the appliance interio...Read morer. The rack’s design promotes proper spacing and water flow, contributing to improved performance and efficiency. Compatible with select Frigidaire dishwasher models, this OEM part is easy to install and sold as a complete assembly. For best results, unplug the appliance before installation and consult your user manual for guidance.

This plastic cover and stem assembly helps hold the lower spray arm in place.