62922113 Kenmore Cooktop - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
burner switch would only stay on hi
0 of 3 people
found this instruction helpful.
-
David from Willow Grove, PA
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench (Adjustable)
Replaced the switch.
Was this helpful?
Thank you for voting!
The paint had chipped and peeled on the inlet grill
0 of 4 people
found this instruction helpful.
-
Ann from Irvington, NY
- Really Easy
- Less than 15 mins
I lifted off the old grill and replaced them with the new ones. My stove top looks great again. If I could find them, I would like to replace the knobs to turn on the gas!
Was this helpful?
Thank you for voting!
Door would not close
-
Hugh from Albuquerque, NM
- Really Easy
- 15 - 30 mins
-
Screw drivers
Opened oven door. Inserted a small bent nail into the small holes on the hinge. This locks the hinge from closing all the way. Removed the chrome hinge retaining plates. One at each hinge. Lifted the door off the oven. Laid door on towel. Removed 3 screws from the top of door, three screws from the bottom of door. This allows you to se
... Read more
parate the two pieces of the door. Clean all glass surfaces, including the ones under the middle glass panel. Removed 1 screw from each hinge at bottom of door. Pull hinge from bottom of door after removing screws. Insert new spring at top of door first, replace retaining screw. Realign the two door parts and replace all screws. Set door back on hinge pocket. Be careful to insure that the hinge seats into the pocket. Open door just enough to replace retaining plates. Process was easy, but it did not fix the problem completely. Bought heavy magnets from hardware store and installed them inside the door. This with the new hinge fixed the problem.
Read less
Was this helpful?
Thank you for voting!
Jenn Air oven door would not stay closed all the way so the light stayed on.
-
Mary T from Glenoma, WA
- Easy
- 15 - 30 mins
-
Screw drivers
Unlike many here, the oven door closed enough to come up to temperature quickly and I could not feel any heat escaping. The oven worked fine but the light stayed on because the door just wasn't snug enough. I watched the great how-to video and ordered the hinges. They arrived in two or three days! I set up a work space, cued up the video
... Read more
again and the new hinges were installed in just a few minutes! But the door would not close enough to turn the light off! I did some more googling around and found the magnet trick! I just happened to have the perfect size magnet from a broken souvenir magnet! and now the light stays off! I stuck the magnet (about the size of a nickel) inside the door opposite the light button. This won't help if you have serious problems with the oven door, but it works if the only problem is the light!
Read less
Was this helpful?
Thank you for voting!
oven door didn't shut completely
-
Kris from Murfreesboro, TN
- Easy
- 15 - 30 mins
-
Screw drivers
We found the youtube video created by partselect.com and followed it. We took the door apart, cleaned the inside, removed the old hinges and replaced them with the new ones. Now the door works perfectly!
Was this helpful?
Thank you for voting!
Jennaire 4 burner stove top right two burners coming on full heat with either controls.
-
Llewellyn P. from Junction, TX
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
Read privious fixes. Didn't know which control was bad but ordered two new ones. Marked locations of switch contacts and wire colors. Removed old controls. Installed new replacements and everything works fine. Thanks.
Was this helpful?
Thank you for voting!
hinge broke on bottom oven door.
-
Dolores from Penrose, CO
- Really Easy
- 15 - 30 mins
-
Screw drivers
sorry, son did job. It went like a charm. Easy, quick, and works great.Thanks
Was this helpful?
Thank you for voting!
A burner on the cook top stopped working
-
Gina from Oak Harbor, WA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
I switched the circuit breaker off at the electrical panel, removed the burner switch assembly (two screws) from the cook top. The burner switches are held in place by a single nut over the control stem. I unscrewed the nut from the failed switch, disconnected the four electrical leads (one by one) from the old switch and connected them i
... Read more
n the same position on the new switch and replaced the nut. The clips on the electrical leads were oxidized/tarnished so I cleaned them with emery cloth to assure good contact with the posts on the switch. Replaced the burner switch assembly in the cook top, energized the circuit and the burner works perfectly again.
Read less
Was this helpful?
Thank you for voting!
Holes in the air filter of our Jenn-Air grill
-
Janice from Ocala, FL
- Really Easy
- Less than 15 mins
Simply pulled the old filter out and put the new filter in.
Was this helpful?
Thank you for voting!
Replacement
-
Barb from Holladay, UT
- Really Easy
- Less than 15 mins
-
Screw drivers
This down draft filter was just what I was looking for. The big box stores (Home Depot and Lowe's) do not carry this size filter. Thanks,
Was this helpful?
Thank you for voting!
grill would not get hot enough
-
Paul from Berlin, MD
- Really Easy
- Less than 15 mins
I have a newer jenn air with the 3 prong elements. The original element was 3 prong 1900W only using one of the controls. Since the stove socket would accommodate 4 prongs I looked up the part for the older stoves (PS2357533)which had 2 elemants using both controls. The element plugged right in and I now have high heat like on my older
... Read more
models and it now grills like it should instead of just heating the stuff up. Highly recommended. One caution you will need a metal piece to support the element since the newer stoves do not use the metal bricketts with supports.
Read less
Was this helpful?
Thank you for voting!
broken surface burner knob
-
dave from williston, VT
- Really Easy
- Less than 15 mins
-
Pliers
Pulled off the knobs,replaced switch, put on the new knobs. Your web site is easy to use, and your parts are first quality. Dave
Other Parts Used:
Was this helpful?
Thank you for voting!
old grill burnt out
-
Kay from Fontanelle, IA
- Really Easy
- Less than 15 mins
took new element out of box, inserted it into stovetop, everything was over in about 2 minutes. It worked just fine.
Was this helpful?
Thank you for voting!
burner only work on high heat
-
neil from CONYERS, GA
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench (Adjustable)
Turn off circuit breaker to cooktop. Remove 2 screws that hold switch plate assembly.Remove tinnerman nut from old switch using adjustable wrench. Remove one wire at time from old switch to same location on new switch. Return shaft back through hole and replace nut, be careful to not overtighten. Replace control know, turn circuit breaker
... Read more
back on and test. Works like new. Neil
Read less
Was this helpful?
Thank you for voting!
Door Hinge broken
-
Antonio from Davie, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
I followed the online video at Jennair.com. The repair was easy and I saved quite a bit of money. I was quoted a price of $534.00 to replace the door hinges, I did it for $96.00 including overnight shipping chargers. I am a very happy lady.
Was this helpful?
Thank you for voting!