62922113 Kenmore Cooktop - Instructions

pulled old one out , cleaned the area & replaced with the new one.

Removed the old grease screen and cleaned the entire area thoroughly and replaced the screen

I had put up with a filter that got more and more raggedy every year, but I thought my 30 yr. old range/grill top was too old for me to find an replacement filter. What a great service you offer. I found you by web-surfing, typed in the model #, and presto--you sent me the shiny new filter. All I had to do was pop it in and throw away ... Read more the nasty grill (after washing the scent off to keep the bears out of my Colorado garbage.) Thank you!

Cleaned out the downdraft cove, inserted the new filter, and put old filter in garbage can. Laughing. Thanks. Wish you had a FAQ's hotline. I'd like to know if the radiant inserts fit the older coil-type models.

Parts arrived in three days and it was an easy swap of the hinges but the same problem still existed: the oven door wouldn't close completely, so the oven light stayed on and the convection wouldn't work either unless the door closed all the way. The replacement hinge's springs apparently aren't strong enough to close it and the springs a ... Read more ren't adjustable - which is a design flaw. I did correct the problem though, by using three dollars worth of 1" round magnets, which I placed inside the door: they stay put and are strong enough to pull the door tight.

First I cut off power supply, removed screws that held panel on, pulled the switch up and disconnected wires. Installed new switch, being sure to connect wires in the correct places. Refastened panel to stove top. Turned power back on and tested switch and it Worked.

It's wonderful to get accessories for this 20 year old Jenn-Air. I love it and now it looks like new.

One oven door hinge spring was broken. I ordered two hinges to complete the repair.
The repair could not have been easier. I removed the door from the oven an unscrewed the outer frame of the door from the inner door assembly. I unscrewed the old hinge assembly and replaced them with the two new hinges.
I set the door back on ... Read more the oven and replaced the oven door retaining hardware.
After replacing the retaining hardware, I removed the temporary shipping pins that keep the spring assembly static. Very important: don’t remove these hinge pins until the door is on the oven an the oven retaining hardware is secured.

Remove oven door by removing chrome flat plate that holds the hinge in place (one screw at each hinge) and LIFT door off oven. There is a hole in the hinge that you can stick a small nail through to hold the hinge in the "partially open" position for easier removal and replacement of the door (I didn't know this until I received the new ... Read more hinges, which have a removeable pin in the hole.) After door is off, remove three screws each, on the top and bottom of door, to remove the back half of door and expose the hinges. Remove one screw from bottom of door that holds bottom of hinge in place. Lift out hinge bottom and unhook top of hinge. Reverse process to reassemble. Remove small pins by opening oven door fully. The new hinges did solve the problem. You have to order two hinges for each door. They are NOT sold as pairs.

Turned off power.

Removed two screws to free up section of cooktop containing 4 switches - 2 good, 2 damaged. Removed the dials from top of the 2 damaged switches. With an adjustable wrench, loosed nut on stem of switch that fastened switch to assembly. Noted which of the 5 wires on each switch went on which tab. Pulled off 5 ... Read more wires on one switch, finished removing the nut and removed broken switch. Put in new switch, attached the nut, and replaced 5 wires in exactly the same position, Tightened nut. Replaced dial. Repeated procedure for second switch. Placed section containing the 4 switches back on cooktop and inserted/tighted 2 screws holding it in place.

Turned on power.

Told cleaning people to NEVER put aluminum foil under the burner units again. The foil shorted across the power and damaged the switches.

Removed the door then the end caps and inner panel then the hinge system and replaced with the one piece new set of hinges and back together done in 30 to 45 minutes The new parts were a perfect replacement.

We panicked cause even simple repairs on these products cost and cost.....but we remained calm and ordered the exact part necessary from you. It arrived in just 3 days and once we had the part in hand it was easy to understand how to replace it. We disassembled the door with screwdrive and swapped the broken part with the new one. The ... Read more one gotcha was that we were not aware of the shipping pin holding the spring and we struggled for a few trying to get the door closed all the way. Once we discovered the pin and removed it, it was fixed and we were PLEASED!

Thank you,
Louise and Rickl

I replaced the hinges as described in other posts and the problem was solved. When the oven was 2 years old it had the same problem but the hinges should not have fatigued at that point. The engineering problem someone mentioned is that the pin of the light switch is too short. I touched it with lipstick, closed the oven door, and opened ... Read more the door to see exactly where the door touched the pin. I drilled a small hole in the door and screwed in a self tapping metal screw...problem solved for 8 years until the hinges fatigued. After replacing the hinges I tried removing the screw but the light stayed on so I put the screw back.

Important: Down load the helpful assembly diagram for the fan motor and study it for a few minutes. It's very straight forward. Also a good idea is to remove the bottom panel which comes off easy before starting.

My only problem was removing the existing blower/fan wheel without damaging it once I had the assembly on the work b ... Read more ench. It was rusted on tight and managed to remove after a few tries using penetrating oil. The wheel is in stock and I'd suggest buying a new one along with the new motor if I had to do the job again.

Bottom line; the fan motor fit perfect but did have to re-use part of the old existing electric pig tail because the motor does not come with the factory type motor terminal connectors. By using three twist on wire connectors was back in business. The down draft vent works like new.

Wife is happy...

Wade

This repair was so easy. After I examined the faulty part, I removed the old switch fom the control box by using a pair of pliers to loosen the flange nut holding the old switch. I removed it, and put the new one in by reverse order. The old switch was actually the original switch- about 25yrs old. It took longer to open the box. I couldn ... Read more 't believe I could do it and how much I saved in doing it all myself!!!