62922113 Kenmore Cooktop - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Switch Stop Working
2 of 3 people
found this instruction helpful.
-
JESSE from VINEYARD HAVEN, MA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
First I removed the two screws that hold the chrome piece that had the switch in it. I had to disconnect the two lights that light up when the elements go on, had to do that to get to the lock washers that hold the switch in place. Put the new switch in place but couldnt get the new lock washers on the both broke, had to go to the hardwa
... Read more
re store and get new ones just as little bit bigger, they went on slick. The switch works great again, buy new lock washers before you start
Read less
Was this helpful?
Thank you for voting!
switch shorted and burned
2 of 3 people
found this instruction helpful.
-
James from Hillsborough, NJ
- Really Easy
- Less than 15 mins
-
Nutdriver
Removed grill cover, two phillip screws on front end of the vent holding the switch assembly in place. Lifted the switch assembly and removed the two wires (plugged into lugs). Then removed the two universal nuts with a 3/8" nutdriver and removed the old switch. Cleaned area and put the new switch in place and replaced the universal n
... Read more
uts, then attached the wires. Replaced the switch assembly and the two holding screws. Then inserted the grill cover and Voila! Finished
Read less
Was this helpful?
Thank you for voting!
Hmm, let's see, knob didn't match all my other new knobs
3 of 6 people
found this instruction helpful.
-
James from Devon, PA
- Very Difficult
- Less than 15 mins
Oh this was a toughie and I was sweating it out.
With a delicate touch I removed the old knob and pushed on the new knob, 5 seconds
With a delicate touch I removed the old knob and pushed on the new knob, 5 seconds
Other Parts Used:
Was this helpful?
Thank you for voting!
Replace burnt out indicator light
1 person
found this instruction helpful.
-
Melanie from SALIDA, CO
- A Bit Difficult
- 15 - 30 mins
-
Pliers
I feel that the design of the indicator light, with the base attached to the bottom of the lens, is ingenious in that it eliminates the need for fasteners in that confined space, However, the plastic used for the base needs to be more flexible. Part of the base broke off in trying to force the base over the bottom of the lens. Fortunat
... Read more
ely, there was enough left on the base that I could slip it over the bottom of the lens and complete the installation.
Read less
Was this helpful?
Thank you for voting!
Right front burner switch burnt out
1 person
found this instruction helpful.
-
FRANCIS from MILLBURY, MA
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Shut off power. Removed screws holding panel.Removed wires from old switch.Installed wires on new switch and reinstalled panel.EASY
Was this helpful?
Thank you for voting!
Burn was full on or "high" at any switch position other than off.
1 person
found this instruction helpful.
-
Owen B Douglass from BROOMALL, PA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Followed other's instructions from the web site: First - turned off the power at circuit breaker; removed two screws from downdraft vent area; pushed the switch housing back towards vent and lifted; held replacement switch next to defective switch and removed and replaced one wire at a time; loosed switch collar-nut and swapped defective
... Read more
switch for new one. Only issue was the "rat's nest" of wires gave very little room to work, especially if you have average sized hands.
Read less
Was this helpful?
Thank you for voting!
parts needed to be replaced
1 person
found this instruction helpful.
-
Phyllis from MAPLE VALLEY, WA
- Very Easy
- 15 - 30 mins
Hubby & I
Was this helpful?
Thank you for voting!
Broken oven door hinge
1 person
found this instruction helpful.
-
John from HOT SPRINGS, AR
- Very Easy
- 15 - 30 mins
-
Screw drivers
My daughter & I followed the instructions in your video and had fun repairing the door. The video showed exactly how to do the repair. I hope I don't need any appliance parts very soon but I will certainly pull up your web site if I do. Thanks for an excellent instruction video.
John - Hot Springs Village, AR
John - Hot Springs Village, AR
Was this helpful?
Thank you for voting!
Door hinge
1 person
found this instruction helpful.
-
Mr. Mike F from SAN ANTONIO, TX
- Really Easy
- 30 - 60 mins
-
Screw drivers
My wife help take the door off. It was a little heavy . The door came apart very easy and went back the same way.We save over $300 by doing it our selfs.
Was this helpful?
Thank you for voting!
Old fan switch was broke.
1 person
found this instruction helpful.
-
Darrell from Las Vegas, NV
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
You probably want to look inside as you read this. Most of it is straightforward, except the retaining clips.
First, I turned off the breaker switch. Opening the control housing, I disconnected the two leads and wrote down their orientation (one is silver, the other copper). In my JennAir model, an orange burner light is on eit ... Read more her side of the fan switch. The white plastic on the rear is held on by their keyhole shape - just slide them the only way they can. This gives extra working room.
Since the switch plastic was already decayed, I snapped off the whole central square unit leaving the 2 portions held onto the posts by the metal retaining clips. Using a small flathead screwdriver, I pried up the plastic remnants, working around it until the retaining clips came loose/ broke.
The new unit fit perfectly and easily. The new retaining clips needed to be worked down a small circular file to spread the centers out enough for me to work onto the retaining posts. The file was just barely bigger than the existing hole. The clips can be broken if you are too rough or work them too much. After that, I used a pair of snub nosed pliers to push the clips down the posts. They required a considerable amount of force, but they aren't going anywhere anytime soon.
Reconnect the lights, reconnect the 2 leads, and check for any loose wires from other controls and loose parts. Reseat the control housing, turn on the breaker and test.
First, I turned off the breaker switch. Opening the control housing, I disconnected the two leads and wrote down their orientation (one is silver, the other copper). In my JennAir model, an orange burner light is on eit ... Read more her side of the fan switch. The white plastic on the rear is held on by their keyhole shape - just slide them the only way they can. This gives extra working room.
Since the switch plastic was already decayed, I snapped off the whole central square unit leaving the 2 portions held onto the posts by the metal retaining clips. Using a small flathead screwdriver, I pried up the plastic remnants, working around it until the retaining clips came loose/ broke.
The new unit fit perfectly and easily. The new retaining clips needed to be worked down a small circular file to spread the centers out enough for me to work onto the retaining posts. The file was just barely bigger than the existing hole. The clips can be broken if you are too rough or work them too much. After that, I used a pair of snub nosed pliers to push the clips down the posts. They required a considerable amount of force, but they aren't going anywhere anytime soon.
Reconnect the lights, reconnect the 2 leads, and check for any loose wires from other controls and loose parts. Reseat the control housing, turn on the breaker and test.
Read less
Was this helpful?
Thank you for voting!
broken burner grill element
1 of 2 people
found this instruction helpful.
-
KEITH from SALT LAKE CITY, UT
- Really Easy
- Less than 15 mins
plugged new one in
Was this helpful?
Thank you for voting!
The original grease filter was damaged in our dishwasher (it is quite fragile) and needed to be replaced.
1 of 2 people
found this instruction helpful.
-
Martyn from Middletown, OH
- Really Easy
- Less than 15 mins
1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover
Was this helpful?
Thank you for voting!
The control knobs had been damaged by heat
1 of 3 people
found this instruction helpful.
-
Jery from Knoxville, TN
- Really Easy
- Less than 15 mins
Easily removed the old knobs and applied the new ones.
Was this helpful?
Thank you for voting!
Very Easy Repair
2 of 6 people
found this instruction helpful.
-
Donald from Edmond, OK
- Really Easy
- 15 - 30 mins
-
Screw drivers
The door came off easily after I removed the two hinge covers that are attached to the oven. Taking the door off can be done with one person but ideally two.
The new parts fit in perfectly and the hinge pin used for shipping comes out easiest with a pair or wire cutters (you do not cut it just grab it and pull).
Aft ... Read more er that, re-assemble the door and drop in place. It was a snap.
FYI...the shipping was ultra fast and the price was great.
No issues whatsover with the entire process.
The new parts fit in perfectly and the hinge pin used for shipping comes out easiest with a pair or wire cutters (you do not cut it just grab it and pull).
Aft ... Read more er that, re-assemble the door and drop in place. It was a snap.
FYI...the shipping was ultra fast and the price was great.
No issues whatsover with the entire process.
Read less
Was this helpful?
Thank you for voting!
Burner won't get hot
0 of 1 people
found this instruction helpful.
-
Robert from Golden, CO
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
It was very simple. detached front switch panel by removing 4 screws inside top of oven door. Removed knob from old switch and removed nut holding switch to panel. Rotated switch panel to expose guts. replaced wires from old switch to new switch, screwed new switch to panel, replaced old knob. idea came from previous story at this website
... Read more
. Works great.
Read less
Was this helpful?
Thank you for voting!