4625 - Parts

This assembly is the door shelf end cap set for the left and right side of your refrigerator. The function of the door shelf end cap is to attach the inner door liner to the door shelf rail. This will then hold the door shelf rail in place and keep it stable. To make this installation you may need a pair of pliers, other than that the par...Read morets will easily snap in and out of place. These pieces are white and measure almost 2 inches long, 1 inch high, and 1.5 inches wide.

This is not the handle. This is the decorative front insert. This part is for your freezer and is white in color. The insert measures approximately 10 inches long. This part is often replaced along with the handle itself. If this part has broken, cracked, or fallen off, it may need to be replaced after repeated use. To install the new han...Read moredle insert, you must simply pry the old one off and snap the new one into place; no tools required. This is an original OEM part that comes right from the manufacturer.

This is a shelf support for the left side of a freezer. It is used to help support the inside of the shelf from both sides. *Please note: right and left side of shelf support are sold separately. If the shelf in your fridge is unstable, replacing this part could be the solution. Make sure to unplug the refrigerator or freezer from the pow...Read moreer source before beginning this replacement project and safely store food. Follow the instructions in the diagram provided by the manufacturer for further instructions and guidance.

Sold Individually.

This is a plastic OEM drain plug that is attached to the drain system of your appliance and is compatible with several different makes and models of refrigerators, freezers, and air conditioners. This drain plug is used to prevent water from leaking out of the incorrect drain system within the appliance and is normally removed for cleanin...Read moreg and maintenance. If you notice water leaking inside of your appliance, the plug may be improperly positioned or may need replacing. To replace, simply pull off the damaged plug and insert the new plug in its place.

A filter-drier in a refrigerator has two essential functions. The first is to absorb system contaminants, such as water, which can create acids. The second is to provide physical filtration. This means trapping moisture, small metal chips, and dirt found in the refrigerant gas. If your refrigerator motor is constantly running, but the ref...Read morerigerator is not getting cold, the issue could be due to a damaged or faulty filter-drier. Faulty filter-driers are sometimes the cause for abnormal freezer compartment temperatures and partially frosted evaporators. This filter-drier is approximately 11 inches long. Remember to disconnect the power from your refrigerator before beginning this repair.

Introducing the genuine Frigidaire Bearing-Hinge, an essential appliance part for your freezer. Renowned for its superior quality, this OEM part enhances the smooth functioning of your appliance by substantially reducing friction between the door hinge and the door panel. This offers gentle movement each time you open or close your freeze...Read morer door. Please remember to safely store any perishable food and disconnect the freezer before you begin with the installation of this part. For best results, it is recommended you wear protective gloves during the installation to safeguard your hands. Trust in Frigidaire's commitment to quality and durability with this excellent Bearing-Hinge.

This is a genuine Murray replacement part, it is sold individually. It is commonly used in lawn tractors, and is used in various places in the compatible models listed below. It is self tapping, with a 9/16 hex head. Made of metal.

This part is found in freezers. The stud may have broken over time and may no longer be supporting the shelf. If your shelf is not staying in place or you are not able to adjust heights, it may be due to the support being broken. To complete this repair, you will need to open the fridge and remove the drawer and the shelf. To remove the o...Read moreld stud, you will need a 3/4-inch wrench to twist it off. The new part should push into place and will need to be turned with your wrench to be secured into place.

Introduce your kitchen to the impeccable, durable, and authentic Frigidaire Gasket, designed specifically to enhance the efficiency of your appliance. This genuine replacement part doubles as a detachable Door Gasket and a Crisper Drawer, adding versatility to its lineup of advantages. Notably, its harmonious compatibility with certain Fr...Read moreigidaire models ensures an optimal functionality balanced with utmost convenience, proving instrumental in your everyday culinary journey. Made with high-grade materials, this product promises longevity, allowing you to make the most of your appliance without frequent part replacements. Ensure a seamless repair experience with this Frigidaire part, your trustworthy companion in appliance maintenance. Embrace the reliability of Frigidaire, a brand renowned for its superior quality appliance parts.

This mandrel housing is for lawn tractors. Mandrel housing houses the shaft that spins the blade. Wear work gloves to protect your hands when installing this part.

This cotter pin is an OEM part that is 1.25 inches long, gold in color, and sold individually. Made of metal, it can have a range of applications on a variety of lawn and garden equipment. Generally, you will need to replace this part if it becomes broken due to age and wear, or if you need to remove it for making other repairs. This is...Read more an easy repair that only requires a pair of pliers to carry out. You need to bend one end around the shaft or bolt and bend the other around the back end of the bolt to complete the repair.