3XART72 Whirlpool Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water would not come out of the dispenser.
11 of 11 people
found this instruction helpful.
-
Ralph from Saint Petersburg, FL
- Easy
- 15 - 30 mins
-
Screw drivers
Removed catch tray and then removed two screws that are underneath. I left the control panel hanging from its wires, then removed the two screws from the control bracket.
A word of caution before next step: You need to remove the two micro switches on the left and right. While trying to remove one, it split apart and the pieces fell ... Read more out. I was able to put it back together and it worked fine. So be careful with the micro switches.
Continue tranferring wires and switches to the new bracket and reassemble in the opposite order.
An easy repair.
A word of caution before next step: You need to remove the two micro switches on the left and right. While trying to remove one, it split apart and the pieces fell ... Read more out. I was able to put it back together and it worked fine. So be careful with the micro switches.
Continue tranferring wires and switches to the new bracket and reassemble in the opposite order.
An easy repair.
Read less
Was this helpful?
Thank you for voting!
ice maker and water dispenser would not work due to switch clamps being broken off the control plate
13 of 18 people
found this instruction helpful.
-
scott from huntersville, NC
- Easy
- 15 - 30 mins
-
Screw drivers
remove the front cover. everything else is a quick disconnect type of connection. Nothing to it! I would remove the cover and check these connections anytime the dispenser does not work. Look for broken or disconnected switches. This reapir took me a couple of minutes whereas the repair guy wanted almost 200 bucks to do this job. Parts ra
... Read more
n around 30 with shipping.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
'Frig door made a popping sound when opening and closing.
11 of 12 people
found this instruction helpful.
-
Lance from Richardson, TX
- Really Easy
- 15 - 30 mins
-
Socket set
Removed upper hinge cover and hinge, lifted door from lower hinge socket, removed lower cam from 'frig hinge, and replaced with new. I had a helper hold the 'frig door while I removed old upper cam, and replaced with new. Piece of cake and works like new! This must be a design problem..
Other Parts Used:
Was this helpful?
Thank you for voting!
Scratches in Surface
83 of 228 people
found this instruction helpful.
-
Michelle from Richardson, TX
- Really Easy
- Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
Cover Pan Crisper(bottom glass shelf and frame) were broken
13 of 18 people
found this instruction helpful.
-
anthony from ormond beach, FL
- Really Easy
- Less than 15 mins
New part slipped right into the studs and fit perfectly
Was this helpful?
Thank you for voting!
the ice dispenser, micro switch control bracket broke and the ice was not dispensing
11 of 12 people
found this instruction helpful.
-
Nelson from East Orange, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed the screws that held the control breaket. Then I removed (2) micro switches, and for a cable tie, I slide the old control bracket out and installed the new one purchased from your store. 5 minutes worth of work. THAT IT!!! It was very, very, simple the repair
Was this helpful?
Thank you for voting!
Ice Door Leaking
13 of 19 people
found this instruction helpful.
-
Steve from Metairie, LA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Remove the unit cover by unsnapping from the bottom. Remove the face plate on the switches. The ice door simply snaps off the closing mechanism. The problem I have is that the original door included a heat trace element (keeps the back of the door warm to limit condensation). The new part was simply a new seal. I clipped the leads to
... Read more
the het trace (turn off the fridge before you do that) and put in the new door. When the heat ids on in the house there is no problem with condensation but on warmer days its pretty bad. I cannot find a replacement part with the heating element and have contacted Whirpool. THey haven't responded as of yet.
Read less
Was this helpful?
Thank you for voting!
The piece that covered the light at the back of the fridge burnt a hole in the cover.
11 of 13 people
found this instruction helpful.
-
Jennifer from Islandia, NY
- Really Easy
- Less than 15 mins
First I removed the cover...and then I slid the new piece in. It looks great and so easy a caveman could do it...lol
Was this helpful?
Thank you for voting!
refrigerator door was making a popping noise when opening and closing
10 of 10 people
found this instruction helpful.
-
Vincent D from Blackwood, NJ
- Really Easy
- 15 - 30 mins
-
Nutdriver
Not being a handyman I found this job realtively easy.I took most of stuff off fridge door, to make door easier to handle. I then undid top hinge door screws, 3 of them, lifted door out., replaced 2 cams.When putting door back on fridge, you have to make sure door is in exact position and top hinge is lined up exactly, or door will contin
... Read more
ue to pop a little.It took me a couple of times to get top hinge lined up exactly.
Read less
Was this helpful?
Thank you for voting!
Crisper Pan Side Reales Had Cracked
10 of 11 people
found this instruction helpful.
-
LEVY from HOUSTON, TX
- Easy
- 30 - 60 mins
I just slid the new pan in , partselect has the correct part all the time , I repalced my ice maker once and it took 15 min no problem
Was this helpful?
Thank you for voting!
Broken gooseneck on fill tube
10 of 11 people
found this instruction helpful.
-
Thomas from Brunswick, OH
- Really Easy
- 15 - 30 mins
-
Screw drivers
The gooseneck on the icemaker fill tube extends out beyond the back cabinet of the refrigerator, and is easily broken. Luckily, this part is a piece of cake to replace. You'll literally spend more time pulling out your fridge and cleaning out behind it then you will replacing this part.
Shut off water supply line, and turn of ... Read more f ice maker (lift the metal bar in the ice bucket all the way up). Loosen the hose fitting, and remove two screws. Pull out the old tube, and slide the new one in. You may have to wiggle the tube around from the inside to get the alignment correct. Replace screws and fitting. Turn water and ice maker back on, and check for leaks. It really is that easy! It took me longer to type this than to actually replace the part.
Only one potential catch. The instructions warn that you may have to cut the new tube to match the length of the old tube, so make sure you compare the length of the old and new tube. I didn't have to to do anything - the replacement part was the exact same length of the original. If by chance you do need to cut the tube, you'll need small saw of some sort, such as a coping or hack saw.
Shut off water supply line, and turn of ... Read more f ice maker (lift the metal bar in the ice bucket all the way up). Loosen the hose fitting, and remove two screws. Pull out the old tube, and slide the new one in. You may have to wiggle the tube around from the inside to get the alignment correct. Replace screws and fitting. Turn water and ice maker back on, and check for leaks. It really is that easy! It took me longer to type this than to actually replace the part.
Only one potential catch. The instructions warn that you may have to cut the new tube to match the length of the old tube, so make sure you compare the length of the old and new tube. I didn't have to to do anything - the replacement part was the exact same length of the original. If by chance you do need to cut the tube, you'll need small saw of some sort, such as a coping or hack saw.
Read less
Was this helpful?
Thank you for voting!
auger blades broken
11 of 15 people
found this instruction helpful.
-
Michael from Ponchatoula, LA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Removed ice bin then pulled front cover with nut driver . Pull small rod from side ( one screw holding rod and spring). Pull auger out. Take plastic nut off end ( CLOCKWISE) LEFT HAND THREAD. Keep all ice crusher blades in order when you pull them off. Install new auger and reverse steps. web site has exploded view. It looks difficult but
... Read more
it isn't.
Read less
Was this helpful?
Thank you for voting!
Would not dispence ice
14 of 24 people
found this instruction helpful.
-
Mike from Chickasha, OK
- Easy
- 15 - 30 mins
-
Socket set
Removed screws from front of ice container,replaced drum.
The hardest part was assembly of ice crusher,lucky the arms were lettered as to how they went back together.
The hardest part was assembly of ice crusher,lucky the arms were lettered as to how they went back together.
Was this helpful?
Thank you for voting!
Ice Door broken letting warm air into Ice Maker system which kept freezing up.
25 of 57 people
found this instruction helpful.
-
Anthony from Magnolia, NJ
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I didn't have to buy a new Ice door kit. The part on the Refrig. door I needed I found out was unavailable. The door parts (Ice door parts and the asembly for the water unit) screws into that part. I found out that I would have to replace the whole refrig. door which was $900.00. I took every apart got me some pvc glue used it on the door
... Read more
and bought the original screw online with some other assorted parts,Door switch, etc. and was able to repair in about an hour. Some of the parts are very fraigle so you have to be very careful or you will be buying some new replacement parts.The new nickel and dime parts are expensive. My Icemaker was leaking where the Ice was clumping together in the bin, and when I checked the unit was $125.00. I found a new one and replaced it for about half that price. I am now very happy! (a least until the next project.)
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Broken tray
11 of 15 people
found this instruction helpful.
-
Brian from Los Angeles, CA
- Really Easy
- Less than 15 mins
Remove old tray, replace with new tray.
Simple & easy.
Best part is I ordered on Monday & received on Tuesday!
Simple & easy.
Best part is I ordered on Monday & received on Tuesday!
Was this helpful?
Thank you for voting!