3XART72 Whirlpool Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The edges of the Meat pan slide were broken.
15 of 18 people
found this instruction helpful.
-
Michael from Bakersfield, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the glides under the edges of the meat pan, remove the old pan, put the new pan in and replaced the glides. I was very pleased with PartSelect. I ordered my part, and it arrived the very next day. I will definitely order my next replacement part thru PartSelect.
Was this helpful?
Thank you for voting!
plastic ice cube guide installed
15 of 18 people
found this instruction helpful.
-
Richard from Bloomington, IL
- Easy
- Less than 15 mins
Mine is a simple tale of the missing ice cube dispensor guide. When we moved, the guide was missing so when I built our new home with a kitchen in the basement I wanted to hook up the ice dispensor but when I did, the ice cubes always fell off to one side. I decided to order the misssing part on-line. I ordered it paid for it and then rec
... Read more
eived it the next day-wonderful. Within ten minutes, I was ready to go. Thanks for great service. Rick Davis, Bloomington, IL.
Read less
Was this helpful?
Thank you for voting!
Replace broken ice machine feeder drum
14 of 15 people
found this instruction helpful.
-
David from League City, TX
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Wrench (Adjustable), Wrench set
Be advised that to do this job, you have to take the ice tray and feeder assembly completely apart. The only tricky part is that the nut, part 31 in the drawing, that holds everything together is reverse threaded. Since it's plastic, you're afraid you'll break it. If you know it's reverse threaded to begin with you can go ahead and app
... Read more
ly the required force to get it off.
Read less
Was this helpful?
Thank you for voting!
broken water dispenser spout
15 of 18 people
found this instruction helpful.
-
thomas from corona, CA
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Screw drivers
part arrived within 24 hours.
1. remove plastic front of freezer door water and ice dispenser by looking at bottom edge of plastic for two slots within which to place a stiff scraper blade. very difficult to pop loose and very fragile plastic so take care not to break it. it just pops off two spots on the bottom side and hangs from ... Read more the top no screws or anything.
2. remove the two screws holding the water dispenser spout in place. oh yeah don't forget to turn the water off.
3. this is a long plastic water tube that runs from the dispenser thru a plastic tube channel set in the solid foam core of the door thru the bottom hinge and connects to the water inlet junction.
a. this replacement must be pulled from the dispenser area thru the door and out the bottom but it will not fit without cutting off the end of the spout. the hole in the hinge that it passes thru at the bottom of the door is to tight to allow anything other than the thickness of the tubing.
b. pull the spout end of the tubing upward after disconnecting at the bottom in front behind the air grill. if it moves freely you are in luck - if it does not move freely then it is taped in place on the back of the dispenser area and now that whole assembly has to be unscrewed from the front of the freezer door in order to remove the tape so that the tubing can be pulled thru.
4. once the tubing pulls easily as short distance in either direction it is time to attach the new tubing to the old tubing and pull it out the bottom of the door. i tried to use tape but it pulled off when i got to the door hinge on the bottom and it would not fit thru the hinge.
a. on my model even one layer of tape would not fit thru the hinge. so i put some bricks under the freezer door to hold it up and removed the bottom hinge off of the tubing that was disconnected only a short distance away.
5. use tape or place a screw with the head removed into both the old tubing and the new tubing so it can be pulled from the bottom moving the new tubing into place.
mine broke off in the middle of this process and i had to remove the freezer door. take it completely apart to expose the conduit the tubing slides thru, then run an electrical fish tape thru the conduit and drag the new tubing thru, not a fun process but doable - just takes a bunch of extra time.
6. once the tubing was out the bottom i could then simply thread it thru the hinge easily and reassemble everything.
1. remove plastic front of freezer door water and ice dispenser by looking at bottom edge of plastic for two slots within which to place a stiff scraper blade. very difficult to pop loose and very fragile plastic so take care not to break it. it just pops off two spots on the bottom side and hangs from ... Read more the top no screws or anything.
2. remove the two screws holding the water dispenser spout in place. oh yeah don't forget to turn the water off.
3. this is a long plastic water tube that runs from the dispenser thru a plastic tube channel set in the solid foam core of the door thru the bottom hinge and connects to the water inlet junction.
a. this replacement must be pulled from the dispenser area thru the door and out the bottom but it will not fit without cutting off the end of the spout. the hole in the hinge that it passes thru at the bottom of the door is to tight to allow anything other than the thickness of the tubing.
b. pull the spout end of the tubing upward after disconnecting at the bottom in front behind the air grill. if it moves freely you are in luck - if it does not move freely then it is taped in place on the back of the dispenser area and now that whole assembly has to be unscrewed from the front of the freezer door in order to remove the tape so that the tubing can be pulled thru.
4. once the tubing pulls easily as short distance in either direction it is time to attach the new tubing to the old tubing and pull it out the bottom of the door. i tried to use tape but it pulled off when i got to the door hinge on the bottom and it would not fit thru the hinge.
a. on my model even one layer of tape would not fit thru the hinge. so i put some bricks under the freezer door to hold it up and removed the bottom hinge off of the tubing that was disconnected only a short distance away.
5. use tape or place a screw with the head removed into both the old tubing and the new tubing so it can be pulled from the bottom moving the new tubing into place.
mine broke off in the middle of this process and i had to remove the freezer door. take it completely apart to expose the conduit the tubing slides thru, then run an electrical fish tape thru the conduit and drag the new tubing thru, not a fun process but doable - just takes a bunch of extra time.
6. once the tubing was out the bottom i could then simply thread it thru the hinge easily and reassemble everything.
Read less
Was this helpful?
Thank you for voting!
Ice bin drum blades broke into pieces wouldn't despense ice.
14 of 16 people
found this instruction helpful.
-
Becky from Hamlet, NC
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
After removing a few screws to get to the drum my husband had it back to working like a charm.This part seems to be better made than the original part in the refrigerator.
Other Parts Used:
Was this helpful?
Thank you for voting!
Not enough door storage
13 of 14 people
found this instruction helpful.
-
Dennis from Owings, MD
- Really Easy
- Less than 15 mins
Excellent fit and installation. The door bins slid right in and created the extra space needed on the shelves.
Was this helpful?
Thank you for voting!
bad door gasket
14 of 17 people
found this instruction helpful.
-
William from Palm Coast, FL
- Very Easy
- 30 - 60 mins
watched video. Very easy
Was this helpful?
Thank you for voting!
Cracked Crisper Drawer
13 of 15 people
found this instruction helpful.
-
Jennifer from Salvisa, KY
- Really Easy
- Less than 15 mins
This company is WONDERFUL! I ordered the wrong drawer the first time, but their return process was a snap and the correct drawer arrived the next day. It's great to know that there is someone out there with just about every part you'll need for about any appliance that is truly customer friendly.
Was this helpful?
Thank you for voting!
Shelves and bin were missing
16 of 24 people
found this instruction helpful.
-
Dana from Cary, NC
- Really Easy
- Less than 15 mins
My freezer compartment was difficult to use efficiently with the two shelves and the bin missing. I was thrilled to find these replacement parts ... now it's back to like new.
Other Parts Used:
Was this helpful?
Thank you for voting!
The refrigerator door made a terrible bang every time it was opened.
13 of 15 people
found this instruction helpful.
-
Hank from Seattle, WA
- Really Easy
- 15 - 30 mins
-
Nutdriver
The hardest part was unloading all the food from the refridgerator door! Once done, pry shroud off top door hinge, remove 3 screws and hinge plate. Lift door off bottom hinge. Remove one screw from bottom of door, remove and discard old lifter cam and spacer. Clean up a bit. Install new spacer and lifter cam. Tighten new screw firml
... Read more
y. Replace the lifter cam and spacer on bottom hinge pin (affixed to refridgerator body) using the same method. Replacing the door is easiest if 2 people do it. One person to lift and steady the door, the other has to lie on the floor and guide the door onto the hinge pin. Replace top hinge plate and screws. Snap shroud back over top hinge plate. Replace food in refridgerator. Close door. Done!
Read less
Was this helpful?
Thank you for voting!
The Ice maker would not work.
22 of 42 people
found this instruction helpful.
-
Jerry from Boulder, CO
- Easy
- 1- 2 hours
-
Screw drivers
We rolled the refrigerator out away from the wall and it was obvious where the break was located. We took out the old water spout for the ice maker and replaced the tube and the tubing from the solenoid. We turned it on and soon we had water dripping everywhere. We unloaded and defrosted the freezer which got all of the remaining ice th
... Read more
at was stuck in there. We put everything back together. I read in some instructions in the manual that it might take 24 hours for the ice maker to reprogram itself and start producing ice. I was only about 12 hours and we had ice again and everything worked well. You really do not have to disconnect the water from the main line, the solinoid controls that part of operation and turns the water off until the ice trays are free and clear.
JLB
JLB
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
spout on water dispenser broken
13 of 15 people
found this instruction helpful.
-
JIM from SACRAMENTO, CA
- Easy
- 15 - 30 mins
-
Screw drivers
Cut off old nozzle. Tried electricians tape to join the old and new tubing for fishing, but tube with tape on it, wouldn't fit through hole in hinge at bottom of door. Fished nylon twine through new tube then old tube from dispenser end and was able to feed old tube out and new tube in. Fast and easy. Took more time to clean all the d
... Read more
ust and dirt I found down under, than to make the repair.
Read less
Was this helpful?
Thank you for voting!
Broken cup water fill on ice maker
13 of 15 people
found this instruction helpful.
-
Matthew from Aurora, CO
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.
Thanks,
Matt
Thanks,
Matt
Was this helpful?
Thank you for voting!
Auger drum broke
15 of 22 people
found this instruction helpful.
-
Michael from Deer Park, TX
- Really Easy
- Less than 15 mins
-
Nutdriver, Wrench (Adjustable)
Very easy. Your online video was agreat help.
Was this helpful?
Thank you for voting!
Old, cracked freezer door gasket
12 of 13 people
found this instruction helpful.
-
Ken from ALBANY, OR
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
This is in a rental house; Refrigerator/freezer has been off for a few weeks so just opened the freezer door and used screwdriver to pry out one corner then pliers to grab and pull old gasket (seal) off. Had the new one laid out overnight to relax it; placed one corner on and then the opposite corner then repeated the other two corners.
... Read more
Positioned the keeper edge plastic all of the way around to place the gasket in the door. Closed the door to check the seal and plugged unit back in. Waited and then checked air temp with hand held IR temp gauge. All checked good, no cold spots anywhere. Piece of cake!
Read less
Was this helpful?
Thank you for voting!