EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3XART71 Whirlpool Refrigerator - Instructions

All Instructions for the 3XART71
106 - 120 of 1122

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
door was making a poping sound upon opening and closing
10 of 12 people found this instruction helpful.
  • Tony from Mesquite, NV
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Socket set
First I removed all contents from inside refrigerator door.Then I removed (1) 10mil screw,which holds cover for top hinge.Next I removed the (3) hinge screws,and lifted door off of bottom hinge.Pulled off plastic closure cam from bottom metal hinge post.I cleaned metal post ,applied a small amount of vaseline to post, slid on new plastic cam,installed door, replaced screws.Very easy,10 to 15 min tops.
Was this helpful?
Thank you for voting!
auger blades broken
11 of 15 people found this instruction helpful.
  • Michael from Ponchatoula, LA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Removed ice bin then pulled front cover with nut driver . Pull small rod from side ( one screw holding rod and spring). Pull auger out. Take plastic nut off end ( CLOCKWISE) LEFT HAND THREAD. Keep all ice crusher blades in order when you pull them off. Install new auger and reverse steps. web site has exploded view. It looks difficult but it isn't.
Was this helpful?
Thank you for voting!
Ice Door broken letting warm air into Ice Maker system which kept freezing up.
25 of 57 people found this instruction helpful.
  • Anthony from Magnolia, NJ
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
I didn't have to buy a new Ice door kit. The part on the Refrig. door I needed I found out was unavailable. The door parts (Ice door parts and the asembly for the water unit) screws into that part. I found out that I would have to replace the whole refrig. door which was $900.00. I took every apart got me some pvc glue used it on the door and bought the original screw online with some other assorted parts,Door switch, etc. and was able to repair in about an hour. Some of the parts are very fraigle so you have to be very careful or you will be buying some new replacement parts.The new nickel and dime parts are expensive. My Icemaker was leaking where the Ice was clumping together in the bin, and when I checked the unit was $125.00. I found a new one and replaced it for about half that price. I am now very happy! (a least until the next project.)
Was this helpful?
Thank you for voting!
leaking water dispenser
12 of 19 people found this instruction helpful.
  • roxana from dinuba, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
worked great parts were perfect!
Was this helpful?
Thank you for voting!
There was no light on in refrig area
12 of 19 people found this instruction helpful.
  • Lori from Chuluota, FL
  • Easy
  • Less than 15 mins
  • Screw drivers
Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.
Was this helpful?
Thank you for voting!
Broken shelf support
9 of 10 people found this instruction helpful.
  • Arthur from West Chicago, IL
  • Really Easy
  • Less than 15 mins
snapped in. The best part was the ease that i identified the part due to your website.
Was this helpful?
Thank you for voting!
The refrigerator leaked water every time the ice maker filled.
11 of 16 people found this instruction helpful.
  • Robert E. from Darien, IL
  • A Bit Difficult
  • Less than 15 mins
The problem was discovered to be a cracked fill tube head, This part extends behind the refigerator and is VERY vulnerable to breakage when the box is pushed backagainst a wall space! Placing a shim under the vertical part of the fill tube fixed the problem even without replacing it with the new part. So, now I have a spare!
Was this helpful?
Thank you for voting!
broker door on ice shute
14 of 25 people found this instruction helpful.
  • John from Willington, DE
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
hardest part was getting up the nerve to pull front cover because it is plastic afraid i would brake it pull from bottom and lift up one screw holds old door inplace uplug electric new door doesn't have electric that it.
Was this helpful?
Thank you for voting!
Worn out door chute
14 of 25 people found this instruction helpful.
  • Murali from Rochester, MN
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
Pry open the front dispenser outer cover. Remove a screw holding ice door dispenser unit, remove old door chute, remove and place coil kind of stuff (connecting to panel) old chute to new one and reinstall.
Was this helpful?
Thank you for voting!
THERMOSTAT
9 of 10 people found this instruction helpful.
  • dominique from COMPTON, CA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I followed your instructions , the only thing that was left out was that the freezer has a drain hole that had to be thawed out with a hair dryer,till the water went to the drain pan underneath the ref. your instruction were through enough, that's why I purchased the part from your company, I installed the part 2 days ago and its working like new again 23.00 for the part instead of 1200.00 dollars for another ref. thanks very much. 6 months ago I purchased the relay and compressor starter from your company at that time per your instructions I shook the compressor starter and like a light bulb it had something broke inside,I needed that thanks again oomk
Was this helpful?
Thank you for voting!
tube got cut and it leaked
9 of 11 people found this instruction helpful.
  • Robert G. from Kalkaska, MI
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
first I turned off the water supply then I removed screw that was holding the nozzle and pulled out the tube then I pried out the face plate by prying from the bottom with a thin screw driver then I unpluged the wire harness so I could access the black tube guide that the white tube was housed in before it was cut I pushed the new white tube down threw the black tube and out the bottom hinge I replaced the nozzle screw plugged the harness back in replaced the face plate went to the bottom and connected the tube to the other half replaced the bottom molding and turned on the water
Was this helpful?
Thank you for voting!
The shelf runner broke
10 of 15 people found this instruction helpful.
  • Andrew F from Media, PA
  • Really Easy
  • Less than 15 mins
Took out the old one and put in the new one. No tolls required. It did give me the opportunity to clean the back wall of the refrigerator.
Was this helpful?
Thank you for voting!
Broken Crisper Frame And Pan
9 of 12 people found this instruction helpful.
  • Mauricio from National City, CA
  • Really Easy
  • Less than 15 mins
Jus took me seconds to replace both items. No problem.
Was this helpful?
Thank you for voting!
Worn Down Upper And Lower Cam
8 of 9 people found this instruction helpful.
  • Jose from Corona, CA
  • Easy
  • 30 - 60 mins
  • Pliers, Wrench set
Took off refrigerator door from top hinge and lifted off. A little difficulty getting worn out parts off (needed dremel to drill out worn plastic); replaced with new parts, the screw head holding on the part was starting to be worn as well but still worked. If I hadn't got to this repair soon the bottom of the door aluminum would have t otal worn out as it is, it has a deep groove but not noticeable. The new cams also force the door closed tight instead of slightly ajar at times.
Was this helpful?
Thank you for voting!
Broken rear cabinet rollers
8 of 9 people found this instruction helpful.
  • Jeff from East Schodack, NY
  • Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
Removed the rear cardboard cover and cleaned the area around the compressor and as much of the condensor and fan area as possible. Removed the two base section securing bolts. Jacked the rear of the cabinet up enough to seperate the base from the cabinet. Removed the roller pins and removed and replaced both rollers. Lowered the cabinet back into place, replaced the base bolts and the cardboard cover. The rollers that were sent were of much better quality than the original plastic type and should last the life of the refrigerator. Be careful when moving the fridge as the original rollers may cut into or scratch the flooring.
Was this helpful?
Thank you for voting!
All Instructions for the 3XART71
106 - 120 of 1122