EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3XART71 Whirlpool Refrigerator - Instructions

All Instructions for the 3XART71
121 - 135 of 1122

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
replacing thermostat did not help
10 of 15 people found this instruction helpful.
  • John from Rocky River, OH
  • Difficult
  • More than 2 hours
  • Pliers, Screw drivers, Socket set
Icecubes came out half-way, and refrooze. I figured out, that the melter does not work (HEATER in the icemaker) Voltage measured 105V no load. Studied the Internet, and folloved an advice: shorted the back wire and the blackwire with white stripes.these go to relay contacts. It seems, that the relay contacts are no good on Infrared receiv er boaed. I turn off manually the icemaker, when needed
Was this helpful?
Thank you for voting!
Chrisper pan support cracked due to overfilling
9 of 13 people found this instruction helpful.
  • David from Lenexa, KS
  • Easy
  • Less than 15 mins
removed old shelf support after taking out the glass and support. New part was a perfect fit that was a "shap: to put in.
Was this helpful?
Thank you for voting!
35 year old water tube became brittle and cracked; leaking water
8 of 10 people found this instruction helpful.
  • Melvin from OPELIKA, AL
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Unscrewed clamp holding water tube to refrigerator ice maker. Pulled water tube from ice maker and water valve inlet. Cut the new tubing to the exact same length and inserted one end to the water valve inlet and the other end to the ice maker then screwed clamp holding water tube back to the refrigerator ice maker.
Was this helpful?
Thank you for voting!
Ice dispenser auger would not rotate and drop ice
8 of 10 people found this instruction helpful.
  • jay from Sarasota, FL
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
First, I replaced the auger motor at a cost of $87.00. That job took about 15 minutes and was very easy, but it still didn't work. So, I took off the front panel that covered the ice/water dispenser controls and some white plastic parts rained down out of it. I then discovered the problem was the mounting points that held the ice dispe nser switch in place. The $13.00 white control bracket fixed the problem. Should have checked this first, as I later learned that the motors rarely go bad.
Was this helpful?
Thank you for voting!
Damaged door trim in fridge. ( Rental)
8 of 11 people found this instruction helpful.
  • Bob from Madison, IN
  • Really Easy
  • Less than 15 mins
Slid out old ones and installed new ones
Was this helpful?
Thank you for voting!
light not working in fridge
7 of 8 people found this instruction helpful.
  • Michael from East Meadow, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!
Was this helpful?
Thank you for voting!
ice chute broke
7 of 8 people found this instruction helpful.
  • Cathy from North Liberty, IA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Just like they told me to do.Insert bottom then sides.
Was this helpful?
Thank you for voting!
water nozzle was cracked and leaked
7 of 8 people found this instruction helpful.
  • Stephen from Harahan, LA
  • Easy
  • 15 - 30 mins
  • Screw drivers
I removed the screw holding the nozzle in place, and removed the other end of the line under the refrigerator to give me some slack. Then I clipped the nozzle off of the black line and taped the new line to the end I cut off with electrical tape. Then I just snaked it down through the hole with me pulling from the bottom and my wife pushi ng from the top and reattached both ends. Make sure you don't use too much tape becaue it won't fit throught the hole at the bottom. I taped them together at an angle so not to make tape too thick. Also, you can snake it back from the bottom if the tape breaks and the old line comes out of the fridge.
Was this helpful?
Thank you for voting!
Broken Piece
7 of 8 people found this instruction helpful.
  • anthony from georgetown, IL
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
Had to disassemble ice maker to install part. . .
Was this helpful?
Thank you for voting!
Broken door handle
7 of 9 people found this instruction helpful.
  • Larry from Midlothian, MD
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I removed screws, removed handles, replaced screws and both handles.
Was this helpful?
Thank you for voting!
no power to the ice maker
11 of 21 people found this instruction helpful.
  • Thomas from Indianapolis, IN
  • Really Easy
  • Less than 15 mins
  • Nutdriver
The wiring harness was a straightfoward plug in replacement after depressing the securing tabs, and did provide power to the icemaker. However, the icemaker would continually cycle, with the mold heater on at all times. I suspect this is what caused the thermal fuse to blow in the first place. Rather than spend more time replacing individ ual components, I eneded up replacing the full ice maker assy. The new ice maker works properly.
Was this helpful?
Thank you for voting!
Icemaker Wouldn't Work
7 of 9 people found this instruction helpful.
  • NANCY from KEOKUK, IA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
I removed the screws that attached the drum housing to the bin. I detached the auger & removed the broken drum assembly, turning the auger to the right, opposite what I thought it should be. I slipped the end of the auger into the new bin coupler & put it in place at the rear of the bin. Next I slipped the auger drum into place & ti ghtened it to the left with a socket wrench. I screwed the drum housing to the bin, put the bin back into the freezer & I now have ice through the door again. Easy repair even for me, a 60+ woman.
Was this helpful?
Thank you for voting!
Door Chute Mechanism broke / air flow into ice maker
12 of 24 people found this instruction helpful.
  • Thomas from Clearwater, FL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Have not installed yet as I'm on a quick TX-FL-TX turnaround. Bought and received the part in 24 hours...great. Order contained no instructions. I could probably figure it out myself just have not attempted yet.
Was this helpful?
Thank you for voting!
Ice Maker would no longer move ice through the dispenser
8 of 12 people found this instruction helpful.
  • Sheila from Lena, MS
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
As cookbook authors and publishers, my husband and I depend on our appliances. When our icemaker would no longer work, it was imperative that we repair it as quickly and ecomonically as possible. We had used PartSelect.com earlier to order a part to repair our Jenn-Air stove top and had great results. So, rather than paying a repairman four times or more the cost of the part, we ordered the part and my husband installed it. It took less than 30 minutes to remove the broken auger and install the new one. THANKS PartSelect.com -- we'll use you for all appliance parts needs.
Was this helpful?
Thank you for voting!
Ice Guide broke during cleaning
6 of 6 people found this instruction helpful.
  • John from Albuquerque, NM
  • Easy
  • 15 - 30 mins
  • Nutdriver
Part would not fit straight in. Used universal joint on end of extension to reach screw rather that disassemble front. Managed to slip the paddel just far enough to one side and angled to snap ice guid on and then slipped paddel back into place. Used a dab of candle stickum on the screw head to heep it in the socket and then inserted i n door. $7 part, 15min and saved $$$$$$ over a service call;)
Was this helpful?
Thank you for voting!
All Instructions for the 3XART71
121 - 135 of 1122