EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3XART71 Whirlpool Refrigerator - Instructions

All Instructions for the 3XART71
76 - 90 of 1122

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Refrigerator No Longer Cooling Properly
15 of 15 people found this instruction helpful.
  • Elizabeth from DELRAY BEACH, FL
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Screw drivers
Approximately:

1. Unplugged refrigerator.
2. Emptied Freezer.
3. Removed Ice Maker.
4. Waited a few hours for ice to melt around back panel & nuts.
5. Removed back panel and the cover over fan and fan motor.
6. Waited many more hours for ice to thaw over fins, wiring, etc.
7. Easily replaced the bi -mental defrost thermostat.
8. Replaced panel, fan cover, ice maker.
9. Plugged in refrigerator and waited a bit.

This worked! Yahoo.

p.s. I am a 65+ year old mechanically minded woman. :-)
Was this helpful?
Thank you for voting!
Door would not auto close
18 of 25 people found this instruction helpful.
  • James from Hampton, NH
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
I removed the screws on the upper hinge and removed the door. I removed the lower cam in about 2 minutes and had it replaced. The upper cam was a tight fit in the door and I resorted to vise-grips to remove it. Total time to replace cams and put the door back on was 30 minutes. This saved me $100.
Thanks
Was this helpful?
Thank you for voting!
front roller wheel broke
19 of 29 people found this instruction helpful.
  • Anoop from Diamond Bar, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
its not that hard to replace. may need help to tilt fridge on one side so you can get to the bottom to remove wheel.Had to undo all four corner screws/bolts to loosen bottom section and slowly pull out base frame which holds the 4 wheels. this frame is also holding the compressor and fan so be careful.replace wheel and slowly put frame ba ck to position and screw back bolts. pull back fridge to upright position. leave unplugged for a day or two to allow gas to come back to normal level as we had tilted it.plug it back and it works.
thanks
Anoop
Was this helpful?
Thank you for voting!
Defuser in refrig. would not open
18 of 26 people found this instruction helpful.
  • David from Seaford, DE
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I ordered a Thermostat but didnot need it, here's why. I removed the old thermostat that is under a white plastic cover at the top of the refrig.inside.By the way ,the cover just snaps off very carefully.after ordering a new Defuser and it still would not work I ordered a thermostat hopeing that would open the Defuser to let cool air in t he refrig. Long story short there are two very small holes in the thermostat that hold two very tiny screws, spring activated and one screw while I was looking at the thermostat just fell out in my hand.I put the screw back in the hole and pushed down on the screw with a straight eye glass screwdriver and tighten it. Everything works fine now [just a loose screw].
Was this helpful?
Thank you for voting!
I have a fridge in one of my rentals that was missing 2 crisper drawers
17 of 24 people found this instruction helpful.
  • kevin from macedon, NY
  • Really Easy
  • Less than 15 mins
I ordered the crispers and they came the next day.I took them out of the box and had them installed in about 30 seconds.It doesn't get any easier than that.The lady on the phone was very helpful when I placed the order.The fact that they came the very next day was amazing to me.
Was this helpful?
Thank you for voting!
Ice stripper broken on ice maker
17 of 24 people found this instruction helpful.
  • Kenneth from New Braunfels, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened th e screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!
Was this helpful?
Thank you for voting!
plastic ice cube guide installed
15 of 18 people found this instruction helpful.
  • Richard from Bloomington, IL
  • Easy
  • Less than 15 mins
Mine is a simple tale of the missing ice cube dispensor guide. When we moved, the guide was missing so when I built our new home with a kitchen in the basement I wanted to hook up the ice dispensor but when I did, the ice cubes always fell off to one side. I decided to order the misssing part on-line. I ordered it paid for it and then rec eived it the next day-wonderful. Within ten minutes, I was ready to go. Thanks for great service. Rick Davis, Bloomington, IL.
Was this helpful?
Thank you for voting!
Replace broken ice machine feeder drum
14 of 15 people found this instruction helpful.
  • David from League City, TX
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Wrench (Adjustable), Wrench set
Be advised that to do this job, you have to take the ice tray and feeder assembly completely apart. The only tricky part is that the nut, part 31 in the drawing, that holds everything together is reverse threaded. Since it's plastic, you're afraid you'll break it. If you know it's reverse threaded to begin with you can go ahead and app ly the required force to get it off.
Was this helpful?
Thank you for voting!
broken water dispenser spout
15 of 18 people found this instruction helpful.
  • thomas from corona, CA
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Screw drivers
part arrived within 24 hours.
1. remove plastic front of freezer door water and ice dispenser by looking at bottom edge of plastic for two slots within which to place a stiff scraper blade. very difficult to pop loose and very fragile plastic so take care not to break it. it just pops off two spots on the bottom side and hangs from the top no screws or anything.
2. remove the two screws holding the water dispenser spout in place. oh yeah don't forget to turn the water off.
3. this is a long plastic water tube that runs from the dispenser thru a plastic tube channel set in the solid foam core of the door thru the bottom hinge and connects to the water inlet junction.
a. this replacement must be pulled from the dispenser area thru the door and out the bottom but it will not fit without cutting off the end of the spout. the hole in the hinge that it passes thru at the bottom of the door is to tight to allow anything other than the thickness of the tubing.
b. pull the spout end of the tubing upward after disconnecting at the bottom in front behind the air grill. if it moves freely you are in luck - if it does not move freely then it is taped in place on the back of the dispenser area and now that whole assembly has to be unscrewed from the front of the freezer door in order to remove the tape so that the tubing can be pulled thru.
4. once the tubing pulls easily as short distance in either direction it is time to attach the new tubing to the old tubing and pull it out the bottom of the door. i tried to use tape but it pulled off when i got to the door hinge on the bottom and it would not fit thru the hinge.
a. on my model even one layer of tape would not fit thru the hinge. so i put some bricks under the freezer door to hold it up and removed the bottom hinge off of the tubing that was disconnected only a short distance away.
5. use tape or place a screw with the head removed into both the old tubing and the new tubing so it can be pulled from the bottom moving the new tubing into place.
mine broke off in the middle of this process and i had to remove the freezer door. take it completely apart to expose the conduit the tubing slides thru, then run an electrical fish tape thru the conduit and drag the new tubing thru, not a fun process but doable - just takes a bunch of extra time.
6. once the tubing was out the bottom i could then simply thread it thru the hinge easily and reassemble everything.
Was this helpful?
Thank you for voting!
Ice bin drum blades broke into pieces wouldn't despense ice.
14 of 16 people found this instruction helpful.
  • Becky from Hamlet, NC
  • Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
After removing a few screws to get to the drum my husband had it back to working like a charm.This part seems to be better made than the original part in the refrigerator.
Was this helpful?
Thank you for voting!
gasket width and length about 1inch too short
14 of 16 people found this instruction helpful.
  • Jack from Santee, CA
  • Very Difficult
  • More than 2 hours
  • Nutdriver, Socket set
I'm a retired auto mechanic....I thought this would be an easy job. I figured it would be easier if I removed the fresh food door which I did and it was straight forward. However the "folds" of the new gasket were different than the old one which I thought was an "update". But, after much struggling, I determined that the length and width of the new gasket were each about 1 inch shorter than the old one. When I decided to return the part, I was told that sometimes you have to soak the part in hot water. There were no instructions with the new part regarding this. I decided to buy a new refridge.
Was this helpful?
Thank you for voting!
light inside fridge was flickering and clicking
20 of 35 people found this instruction helpful.
  • bill from escondido, CA
  • Easy
  • 15 - 30 mins
  • Nutdriver
tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok
Was this helpful?
Thank you for voting!
Cracked Crisper Drawer
13 of 15 people found this instruction helpful.
  • Jennifer from Salvisa, KY
  • Really Easy
  • Less than 15 mins
This company is WONDERFUL! I ordered the wrong drawer the first time, but their return process was a snap and the correct drawer arrived the next day. It's great to know that there is someone out there with just about every part you'll need for about any appliance that is truly customer friendly.
Was this helpful?
Thank you for voting!
spout on water dispenser broken
13 of 15 people found this instruction helpful.
  • JIM from SACRAMENTO, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Cut off old nozzle. Tried electricians tape to join the old and new tubing for fishing, but tube with tape on it, wouldn't fit through hole in hinge at bottom of door. Fished nylon twine through new tube then old tube from dispenser end and was able to feed old tube out and new tube in. Fast and easy. Took more time to clean all the d ust and dirt I found down under, than to make the repair.
Was this helpful?
Thank you for voting!
Broken cup water fill on ice maker
13 of 15 people found this instruction helpful.
  • Matthew from Aurora, CO
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt
Was this helpful?
Thank you for voting!
All Instructions for the 3XART71
76 - 90 of 1122