EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3XART71 Whirlpool Refrigerator - Instructions

All Instructions for the 3XART71
61 - 75 of 1122

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ref was warm freezer was still freezing
25 of 36 people found this instruction helpful.
  • richard l. from franklin, KY
  • Really Easy
  • Less than 15 mins
  • Socket set
check what site said was probably the problem 80% of the time. took out one screw unit dropped down disconnected part
connected new part screwed unit backup. Waited 4-5 hrs temp went from 60 degrees to 40.
Was this helpful?
Thank you for voting!
The auger drum had broken, not allowing any ice cubes to be crushed or dispenses through the door.
22 of 28 people found this instruction helpful.
  • Evan from Grand Rapids, MI
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Initially I removed the cover to the auger and auger drum. Then the split ring locking washer had to be removed. I used a needle-nosed pliers and small screw-driver to pry that off. The auger arm could then be removed, and the auger blades removed. This proved to be the part that required the most patience. The blades need to removed and returned in their exact pattern. Someone else suggested taking a digital picture of them before removing them; this is a good suggestion that I failed to do. Once the blades are returned, all the other parts can be replaced in reverse order. Put the screws back in, and you are finished.
Was this helpful?
Thank you for voting!
The old resevoir needed to be replaced
35 of 68 people found this instruction helpful.
  • Fred from Martinsburg, WV
  • Really Easy
  • 15 - 30 mins
  • Pliers, Socket set
The repair was incredibly easy -
1. Turn off the water at the water line for the fridge
2. Disconnect the pressure fittings for both lines running to the resevoir.
3. Remove the old resevoir
4. Install the new resevoir and run the lines back to the orginal fittings.
5. Reconnect the fittings, turn on water.< br />6. Drink water!
Was this helpful?
Thank you for voting!
Refrigeator would not drfrost...
27 of 44 people found this instruction helpful.
  • Curtis from Pikeville, KY
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers, Socket set, Wrench set
I just removed a few screews and took the cover out of the ice box. Put my voltage meter to the refrigeator and realized the the unit was not defrosting...I then got the part number and entered it in on your web site. A few days later my part arrived. I put the part on and in just about 20 minutes I was up an running again...Thank you Part Select for fast and great service. I own 35 rental properties and having a online appliance parts store really saves me a lot of time and money.

Thank you
Curtis Hall
Was this helpful?
Thank you for voting!
Plastic nozzle that dispenses water broke off
18 of 19 people found this instruction helpful.
  • Catherine from Mount Pleasant, SC
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers
the parts sent included two replacement kits which at first was confusing. I determined that I only needed the one with the black tubing for my Kenmore refrig. Turned off water supply and vacuumed up all the dust bunnys behind refrig. Removed bottom grate on refrig where black tubing attaches at the other end. Released water left in t ubing at dispenser. I did not have to remove the front panel. Removed one screw attaching the nozzle to the dispenser. Decoupled tubing at the far end, more water came out here too. Pulled out upper end of tubing a couple of inches and snipped off. Attached tubing to new tubing with thin wire (as others here recommended) and had my husband pull at far end while I pushed slowly at the dispenser end. Once through reattached screw at top and recoupled at the bottom. Mission accomplished!
Was this helpful?
Thank you for voting!
Ice door holder arm broken
20 of 26 people found this instruction helpful.
  • Joseph S from Las Vegas, NV
  • Easy
  • 15 - 30 mins
  • Nutdriver
The hardest part was getting the front cover plate off. I used two kitchen knifes one in each slot on the bottom of the plate and pried it off and unplug it. I removed one screw to release arm. I then used long nose pliers to remove the pin on door arm assemble. Then unplug door heater. New door has no heater. The heater had cooked the pl astic arm, which caused the arm to fail. Then reassemble in reverse order.
Was this helpful?
Thank you for voting!
drawer broke from kids overloading it.
20 of 27 people found this instruction helpful.
  • jonathan from sugar hill, GA
  • Really Easy
  • Less than 15 mins
Pulled out the old drawer and put in the new.
Was this helpful?
Thank you for voting!
Water leaking from under refrigerator.
17 of 18 people found this instruction helpful.
  • Ronald from DELRAN, NJ
  • Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set
Water leaking from under refrigerator. Initially believed leak was from filter assembly. Removed filter and shut off water supply but leak appeared at different intervals again. Large puddle of water coming out from under refrigerator. Removed back lower panel and checked for leak, but didn't find any. My wife was also checking for le ak and found a crack in drip tray. Only way we could get the drip tray out was to first remove front lower panel, disconnect and remove wiring harness in front of drip tray, unbolt water filter assembly, and unbolt water solenoid unit at rear of refrigerator. Their water lines connect to filter assembly. My wife controlled the water solenoid unit to give me play as I pulled the filter assembly out as much as I could from the front. I could now wiggle the cracked drip tray out from under the filter unit. Replaced drip tray and reinstalled wiring harness, water filter unit w/new filter, and re-bolted water solenoid unit at back of refrigerator. Replaced back lower panel after turning water back on and checking for leaks. Replaced front lower panel.

The reason still had leak after initially turning off water supply was because the drip tray is used to catch the water when refrigerator goes into the defrost cycle. Since the original drip tray had cracked, water only appeared on floor after defrost cycle.
Was this helpful?
Thank you for voting!
Ice maker wouldn't deliver ice.
19 of 25 people found this instruction helpful.
  • Berton from Albuquerque, NM
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Removed face plate, disconnected wires, removed and replaced micro switch and control bracket.
Was this helpful?
Thank you for voting!
We broke the rail. :(
17 of 19 people found this instruction helpful.
  • heather from union bridge, MD
  • Really Easy
  • Less than 15 mins
We decided to use our crisper drawers to store sodas. Duh..bad plan. The rail that holds the drawers up cracked in half. So we just had the drawers sitting on the bottom of the fridge. So, I got the new rail THE DAY AFTER I ORDER IT! I just recycled the old one, and slid the new one in. Presto. Perfect fit. Actually, better then perfect. There must have been a defect with my old one, because the new one actually SNAPPED into place, instead if just sitting in the frame. So..I am really pleased.
Was this helpful?
Thank you for voting!
Water began to leak under the refrigerator. Source looked like it was coming from control valve suppling water to ice maker and water dispenser.
21 of 32 people found this instruction helpful.
  • jesse from hacienda heights, CA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Followed instructions supplied. It was relatively easy and the parts fit exactly right. Sears wanted twice as much for the part and service would have charged me another $100 to come to my home. I saved over $100 doing the project myself.
Was this helpful?
Thank you for voting!
nozzle on water dispenser broke off.
16 of 17 people found this instruction helpful.
  • Tom from Roseville, CA
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
First, turn of the water supply. Then remove the snap on grill from the bottom front of the refrigerator. Disconnect the black hose from the white hose and drain the hoses into a suitable recepticle. Then remove the 1/4" screw that holds the nozzle in place. Cut the hose off just behind the nozzle bracket and tape the end of the new h ose to the now exposed end of the existing hose. From the bottom of the door you can now gently pull out the old hose while pulling in the new one. Re-attach the new hose to the existing white hose and replace the 1/4' screw to the new nozzle bracket. I reccoment using 1" wide tape and only going around the tubes once. Too much tape and you won't be able to feed it through the small hole at the bottom of the door. Have someone feed the hose from the top as you gently pull from the bottom.
Was this helpful?
Thank you for voting!
Water dispenser did not work - control switch mount was broken
16 of 17 people found this instruction helpful.
  • Ray from Reno, NV
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
I replaced the control bracket, which has mounts for the switches used to activate the ice and water dispensers. The water switch mount was broken, so the switch would not activate. It was great that I could find this part (the control bracket) on PartSelect's site.

If the person doing the repair has a little patience, then he/ she will be rewarded!:

The first step is to pry off the front panel: I pried off the panel at the bottom. It will pop off, but takes a little effort. I used a couple of screwdrivers to pull it up at a couple of spots at the same time. Once the bottom pops out, then I pulled straight up on the panel. (If you try to pop out the panel at the top, you will damage it, so make sure to pop it out at the bottom.)

Next, disconnect the wiring that goes to the panel, and put the panel aside.

I then took a digital picture of the arrangement of wires and switches on the control bracket.

I disconnected any wires going from the inner part of the refrigerator to the control bracket, and then unscrewed the control bracket.

After removing the old control bracket, I carefully noted how the two switches (one for ice, one for water) mount into it. I removed these switches and put them into the new control bracket.

I then remounted the control bracket into the refrigerator, screwing it into place. I used the digital picture that I had taken earlier to make sure that I knew how to reconnect all of the wires.

I plugged the the remaining wires to the front panel, and then snapped the front panel back into place on the refrigerator door.

I was done!
Was this helpful?
Thank you for voting!
Ice dispenser was not dispensing ice.
16 of 18 people found this instruction helpful.
  • Melvin from Sophia, NC
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Remove the cover plate from the bottom. Use care and patience when performing this step. It takes longer to remove the cover plate than replacing all of the parts involved. Slide off each switch, unplug electrical connectors and trust me when I tell you that you can figure out the rest. E Z, E Z, E Z!!!!!
Was this helpful?
Thank you for voting!
It was not coming out of defrost cycle
25 of 45 people found this instruction helpful.
  • Dale from Flemingsburg, KY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
First I installed a defrost timer, (the old timer had burnt out contacts in it) It seemed to work for a few days, then went back to not comng out of defrost cycle, I then installed a defrost thermostat. It seems to be working better than before. I found out that maybe I wasn't running it cold enough. So I turned it up colder. Now it works ok for 2 - 3 days, then I check the Temp in the freezer and its up to 6o. So I manually reset the timer and it works for 2 - 3 days. Don't know what to do now to fix it.
Was this helpful?
Thank you for voting!
All Instructions for the 3XART71
61 - 75 of 1122