3VED Whirlpool Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
One finger of the spring steel peice that holds the ice maker and water dispenser levers out broke.
35 of 46 people
found this instruction helpful.
-
Ron from Newton, IA
- Really Easy
- 15 - 30 mins
-
Pliers, Socket set
I removed the screw holding the spring steel retainer/clip using a quarter inch ratchet wrench a swivel with a quarter inch socket and a short extention, then just installed the new one. This spring steal through the door ice maker / water despenser lever spring was an easy fix.
I found you by googling appliance repair parts, and fou ... Read more nd your site really easy to use. I couldn't believe how fast the part came and the very reasonable price. I put you on my web browser's favorites.
Thanks,
Ron
I found you by googling appliance repair parts, and fou ... Read more nd your site really easy to use. I couldn't believe how fast the part came and the very reasonable price. I put you on my web browser's favorites.
Thanks,
Ron
Read less
Was this helpful?
Thank you for voting!
Broken front roller set and a snapped shelf support.
31 of 34 people
found this instruction helpful.
-
Jerry from Fostoria, OH
- Easy
- 15 - 30 mins
-
Pliers, Socket set
While moving our refrigerator when remodeling the kitchen, the front roller assembly shattered from age. The original set was made of nylon and age made it very fragile. Also to make the move easier, we removed the shelves. In the process the lower shelf support stud snapped.
When the parts came the first thing repaired was th ... Read more e shelve support stud. Very easy job to do, just take the pliers and rotate the broken stud counterclockwise a quarter turn and remove. Put new stud in the hole in the same position as the removed stud and gently, but firmly rotate the stud a quarter turn clockwise until it seats.
The front roller assembly requires a socket set, block of wood about 1/2 - 1" thick flashlight and 4’ level. First, remove the front grill by opening both doors of the side by side and pulling the grill out of its left and right side anchors. Close the doors. Place the block of wood under the front support near the center. Remove the leveling screw from the old assembly and install it loosely in the new assembly as the new assembly has no leveling screw. This will now allow you to remove the old assembly by removing the remaining screw in the roller assembly on the front refrigerator support and turning the roller assembly slightly counterclockwise and pulling out the front. You may have to wiggle it, as it sits in a slot on the side support of the refrigerator. To install, place the new assembly in the same position as the old, locate the slot with the flashlight and push the roller set tab into the slot. Attach the support screw and tighten while holding the assembly in place. It is a good idea to replace both rollers at the same time. The same rollers will fit both sides. Now level the refrigerator by tightening the leveling screw until the front rollers now touch the floor. Next, place the level on the top of the refrigerator diagonally but not on top of the door supports. Turn the leveling screws until the bubble is in the center when the level is set in either diagonal position. Replace grill and you done.
When the parts came the first thing repaired was th ... Read more e shelve support stud. Very easy job to do, just take the pliers and rotate the broken stud counterclockwise a quarter turn and remove. Put new stud in the hole in the same position as the removed stud and gently, but firmly rotate the stud a quarter turn clockwise until it seats.
The front roller assembly requires a socket set, block of wood about 1/2 - 1" thick flashlight and 4’ level. First, remove the front grill by opening both doors of the side by side and pulling the grill out of its left and right side anchors. Close the doors. Place the block of wood under the front support near the center. Remove the leveling screw from the old assembly and install it loosely in the new assembly as the new assembly has no leveling screw. This will now allow you to remove the old assembly by removing the remaining screw in the roller assembly on the front refrigerator support and turning the roller assembly slightly counterclockwise and pulling out the front. You may have to wiggle it, as it sits in a slot on the side support of the refrigerator. To install, place the new assembly in the same position as the old, locate the slot with the flashlight and push the roller set tab into the slot. Attach the support screw and tighten while holding the assembly in place. It is a good idea to replace both rollers at the same time. The same rollers will fit both sides. Now level the refrigerator by tightening the leveling screw until the front rollers now touch the floor. Next, place the level on the top of the refrigerator diagonally but not on top of the door supports. Turn the leveling screws until the bubble is in the center when the level is set in either diagonal position. Replace grill and you done.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
disfigured, torn along bottom of door
32 of 37 people
found this instruction helpful.
-
james from edina, MN
- Easy
- 15 - 30 mins
-
Nutdriver
I loosen the screws with a nut driver just enough to pull old gasket away from door. This way the door panel and gasket retainer stay in place. I placed gasket from top and worked my way down one side. It took a little more time to slip gasket under retainer evenly, tighten each screw to keep gasket from pulling out while working around
... Read more
door.
30 minuets tops,never had to turn off refrigerator.
30 minuets tops,never had to turn off refrigerator.
Read less
Was this helpful?
Thank you for voting!
meat pan and crisper pan broken runners
32 of 39 people
found this instruction helpful.
-
James from Troy, OH
- Really Easy
- Less than 15 mins
due to over filling and closing the drawers with the door and kicking, the plastic runners broke. Also, over filling the drawers did not help.
AS for the repair, the only difficulty was getting the right drawer in the right spot. Since I replaced both the veggie and meat drawer at the same time, I got them confused. On drawer is ... Read more longer than the other. other than that, no problem.
AS for the repair, the only difficulty was getting the right drawer in the right spot. Since I replaced both the veggie and meat drawer at the same time, I got them confused. On drawer is ... Read more longer than the other. other than that, no problem.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Door chute broken
34 of 45 people
found this instruction helpful.
-
Dwight from Marietta, OK
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
First removed the outside cover plate which was some what scary not to break plastic cover. Had read about another discription of removal of cover to start from the bottom because the top is inserted in slots that would have broken if removed from the top. After cover plate removed it was simple to remove the broken parts and install th
... Read more
e new parts. The most difficult part to put back in was the spring and rod had to be inserted the same time.
Read less
Was this helpful?
Thank you for voting!
Our six year old fridge would not stop running - everything was frozen. Found if I tapped on the Tstat I could sometimes get it to turn off.
29 of 31 people
found this instruction helpful.
-
Jeff from Belleville, WI
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Remove the knobs and faceplate to get at the screws behind it. Removing the sensor is a bit involved but everything else is fairly straight forward. See other postings for description / order of operation. Replacement took less than 30 minutes.
Works great now!
Works great now!
Was this helpful?
Thank you for voting!
Water won't flow from water dispenser
29 of 31 people
found this instruction helpful.
-
Bryan from Eugene, OR
- Easy
- 15 - 30 mins
-
Nutdriver
Found the control bracket housing had broken and micro switch for the water pump was not making contact with mechanical link. (In other words when you put a cup under the dispenser and push water did NOT come out.)
I removed the faceplate and switches, removed all the switches and installed them in the new control bracket. I ... Read more nstalled new control bracket into fridge and tested. Works! Reinstalled faceplate and switches and drained system for a few minutes. Man I forgot how good filtered water tasted!
I removed the faceplate and switches, removed all the switches and installed them in the new control bracket. I ... Read more nstalled new control bracket into fridge and tested. Works! Reinstalled faceplate and switches and drained system for a few minutes. Man I forgot how good filtered water tasted!
Read less
Was this helpful?
Thank you for voting!
Water leaked on floor when water dispenser was used.
28 of 30 people
found this instruction helpful.
-
Dave from Danville, AL
- Really Easy
- 15 - 30 mins
-
Wrench set
1. Turn off water supply to refrigerator.
2. Unscrew water nozzle from dispenser.
3. Remove grill on bottom front of refrigerator.
4. Unscrew tubing at the left side of the union.
5. Unclip tubing from the refrigerator frame.
6. Pull tubing out of the dispenser about 6 inches.
7. Cut off nozzle with scissors. ... Read more
8. Insert 1/4" diameter x 1" long molly bolt about halfway into end of tubing where it was cut.
9. Insert the remainder of the molly bolt into the end of the new tubing.
10. Pull the old tubing through the bottom of the door.
11. When the new tubing is pulled all the way through the door disconnect from the old tubing. Remove molly bolt if it is in the new tubing.
12. Remove the ferrel from the old tubing and use to attach new tubing to the union.
13. Connect the water nozzle to the dispenser.
14. Insert new tubing into the clips on the refrigerator frame.
15. Re-install grill.
16. Turn on water.
2. Unscrew water nozzle from dispenser.
3. Remove grill on bottom front of refrigerator.
4. Unscrew tubing at the left side of the union.
5. Unclip tubing from the refrigerator frame.
6. Pull tubing out of the dispenser about 6 inches.
7. Cut off nozzle with scissors. ... Read more
8. Insert 1/4" diameter x 1" long molly bolt about halfway into end of tubing where it was cut.
9. Insert the remainder of the molly bolt into the end of the new tubing.
10. Pull the old tubing through the bottom of the door.
11. When the new tubing is pulled all the way through the door disconnect from the old tubing. Remove molly bolt if it is in the new tubing.
12. Remove the ferrel from the old tubing and use to attach new tubing to the union.
13. Connect the water nozzle to the dispenser.
14. Insert new tubing into the clips on the refrigerator frame.
15. Re-install grill.
16. Turn on water.
Read less
Was this helpful?
Thank you for voting!
Icemaker arm was broken
33 of 45 people
found this instruction helpful.
-
Jason from Austin, TX
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
The tiny piece of plastic that holds the wire that shuts off the icemaker, broke early on with our fridge (after just a few months.) We superglued it, but last week it bit the dust for good.
Once I got this part, I removed the freezer door and trays, and pulled the icemaker out by removing 3 flathead screws and unplugging the c ... Read more ables. Laying in the freezer on the floor was a bit unconfortable, but not too bad.
Then I inspected the icemaker. There was no obvious way to remove the part without disassembling the front of the unit (where the motor is) to release the spindle and free the part, so I did that - 3 or 4 nuts was all that held it together. Once that was out, I removed the spindle, swapped out the part, and put it all back together and back in the freezer. Plugged it in and waited.
It took a while to start making ice. Like 5 hours. Now it's going pretty slow (much slower than before.) Haven't had time to look into it, but my suspicion is the rubber hose that feeds water into the icemaker is blocked with ice or kinked. In any case, we have ice now (but not a lot), and the unit shuts itself off properly. However, we went from having too much ice (thing never shut off) to too little (thing makes ice too slow), so I need to shoot for somewhere in the middle ;)
Once I got this part, I removed the freezer door and trays, and pulled the icemaker out by removing 3 flathead screws and unplugging the c ... Read more ables. Laying in the freezer on the floor was a bit unconfortable, but not too bad.
Then I inspected the icemaker. There was no obvious way to remove the part without disassembling the front of the unit (where the motor is) to release the spindle and free the part, so I did that - 3 or 4 nuts was all that held it together. Once that was out, I removed the spindle, swapped out the part, and put it all back together and back in the freezer. Plugged it in and waited.
It took a while to start making ice. Like 5 hours. Now it's going pretty slow (much slower than before.) Haven't had time to look into it, but my suspicion is the rubber hose that feeds water into the icemaker is blocked with ice or kinked. In any case, we have ice now (but not a lot), and the unit shuts itself off properly. However, we went from having too much ice (thing never shut off) to too little (thing makes ice too slow), so I need to shoot for somewhere in the middle ;)
Read less
Was this helpful?
Thank you for voting!
Studs were VERY difficult to remove
27 of 28 people
found this instruction helpful.
-
Brad from Niagara Falls, NY
- A Bit Difficult
- Less than 15 mins
-
Pliers
If you have enough plastic to grip with pliers, removal is quite easy. But some of the studs break off at the base making removal very difficult.
I drilled 2 holes and inserted small screws - somthing to grip with pliers. 1/4 turn and they came out.
To insert new studs, a 3/4 turn is required. They will lock in place when prope ... Read more rly inserted.
My biggest complaint is the price, $5.00 per stud is a bit excessive.
I drilled 2 holes and inserted small screws - somthing to grip with pliers. 1/4 turn and they came out.
To insert new studs, a 3/4 turn is required. They will lock in place when prope ... Read more rly inserted.
My biggest complaint is the price, $5.00 per stud is a bit excessive.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
auger or ice crusher in ice container was broken an wouldn't dispense ice
30 of 38 people
found this instruction helpful.
-
Willis from Belleview, FL
- Really Easy
- Less than 15 mins
nothing to repair, simply removed the old ice container and auger from the freezer and replaced with it with the new one.
Was this helpful?
Thank you for voting!
Water dispenser not working, Ice dispenser chute icing up
27 of 33 people
found this instruction helpful.
-
Jeff from Parchment, MI
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
I removed the outer ice/water dispenser cover following directions I found on-line (push down and gently pry out at the bottom). I then removed several nut-head screws which were holding a plastic plate which had the door light and electric control wiring mounted in it. Behind that I found a broken tab on the Control Bracket which was w
... Read more
hy my water dispencer was not working and I found the chute door for the ice maker was chewed up which allowed warm air into the chute and was causing my ice build up problem. Replacing the Control Bracket was easy. Just note how things come apart. Putting the chute door in was a little more complicated, but again, note how things come apart and you should not have a problem putting it back together.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Broken Shelf Bracket
26 of 30 people
found this instruction helpful.
-
Thomas from Leesburg, FL
- Really Easy
- Less than 15 mins
Removed food itmes on broken shelf. Removed old glass shelf cover. Removed broken shelf bracket. Installed new shelf bracket. Intalled new glass shelf cover. Replaced food items back on shelf
Was this helpful?
Thank you for voting!
broken slide
26 of 30 people
found this instruction helpful.
-
John from Rogers City, MI
- Really Easy
- Less than 15 mins
lift out old (broken) crisper drawer cover, replace with new. Replace glass shelf. Took longer to clean the shelf off then it took to replace.
Was this helpful?
Thank you for voting!
broken meat and vegatable draw
25 of 28 people
found this instruction helpful.
-
douglas g. from roanoke, VA
- Really Easy
- Less than 15 mins
a simple replacement
Was this helpful?
Thank you for voting!