3VED Whirlpool Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice dispenser freezing up, dispenser door not closing completely.
22 of 26 people
found this instruction helpful.
-
Robert from Valencia, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
First off, if you have the stainless steel panel inserts on your refrigerator you'll need to remove those to do this repair. I kept looking for the access holes on the underside of the dispenser panel that you're supposed to insert a screwdriver into to pry it off. It wasn't until I removed the freezer door handle, slid the lower stainles
... Read more
s panel insert out, and removed the rail just beneath the dispenser that I could see and access these holes. I also removed the upper stainless panel and rail just above the dispenser to allow enough movement get the dispenser cover off and out. The rest of the repair is pretty straightforward. The old ice door was beaten up and not closing completely, this was letting warm air into the freezer which was melting and re-freezing. This kit fixed the problem.
Read less
Was this helpful?
Thank you for voting!
Plastic Water Spout Broke Off
21 of 23 people
found this instruction helpful.
-
Michael from Colorado Springs, CO
- Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set
Turn off water supply line fridge. Removing front panel is a must to allow acces to spout and water line. Be careful not to crack front panel $90, it snaps in from the botton, slide a stiff putty knife along bottom edge and gently pry outward to remove. Remove 2 screws that hold spout in place, then cut water line right behind spout. The
... Read more
tricky part is fishing water line down through door. You need to splice new line to old with double sided screw or something with threads that will prevent the lines from pulling apart, then pull water line from bottom of door by hinge, very tight when pulling through hinge opening. You will need to remove vented dust cover at botton of doors to acces the water line. The line has a threaded coupling so unscrew and drain water then cut new line to length. There is a small metal insert in old line that needs to be removed and inserted into new line before attaching coupler. I could perform this in half the time now that I have done it once.
Read less
Was this helpful?
Thank you for voting!
The auger drum had broken, not allowing any ice cubes to be crushed or dispenses through the door.
22 of 28 people
found this instruction helpful.
-
Evan from Grand Rapids, MI
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Initially I removed the cover to the auger and auger drum. Then the split ring locking washer had to be removed. I used a needle-nosed pliers and small screw-driver to pry that off. The auger arm could then be removed, and the auger blades removed. This proved to be the part that required the most patience. The blades need to removed and
... Read more
returned in their exact pattern. Someone else suggested taking a digital picture of them before removing them; this is a good suggestion that I failed to do. Once the blades are returned, all the other parts can be replaced in reverse order. Put the screws back in, and you are finished.
Read less
Was this helpful?
Thank you for voting!
The old resevoir needed to be replaced
35 of 68 people
found this instruction helpful.
-
Fred from Martinsburg, WV
- Really Easy
- 15 - 30 mins
-
Pliers, Socket set
The repair was incredibly easy -
1. Turn off the water at the water line for the fridge
2. Disconnect the pressure fittings for both lines running to the resevoir.
3. Remove the old resevoir
4. Install the new resevoir and run the lines back to the orginal fittings.
5. Reconnect the fittings, turn on water.< ... Read more br />6. Drink water!
1. Turn off the water at the water line for the fridge
2. Disconnect the pressure fittings for both lines running to the resevoir.
3. Remove the old resevoir
4. Install the new resevoir and run the lines back to the orginal fittings.
5. Reconnect the fittings, turn on water.< ... Read more br />6. Drink water!
Read less
Was this helpful?
Thank you for voting!
refrigerator would not stay cold
21 of 26 people
found this instruction helpful.
-
Allan from Allen, TX
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
The wife found if we tapped the knob for the cold control the appliance would turn on. Upon further inspection I found what looked to be carbon particles under the part. I found the part easily with partselect.com, ordered it, installed it and its like we have a new appliance.
Was this helpful?
Thank you for voting!
Refrigeator would not drfrost...
27 of 44 people
found this instruction helpful.
-
Curtis from Pikeville, KY
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Socket set, Wrench set
I just removed a few screews and took the cover out of the ice box. Put my voltage meter to the refrigeator and realized the the unit was not defrosting...I then got the part number and entered it in on your web site. A few days later my part arrived. I put the part on and in just about 20 minutes I was up an running again...Thank you
... Read more
Part Select for fast and great service. I own 35 rental properties and having a online appliance parts store really saves me a lot of time and money.
Thank you
Curtis Hall
Thank you
Curtis Hall
Read less
Was this helpful?
Thank you for voting!
Plastic nozzle that dispenses water broke off
18 of 19 people
found this instruction helpful.
-
Catherine from Mount Pleasant, SC
- Easy
- 1- 2 hours
-
Pliers, Screw drivers
the parts sent included two replacement kits which at first was confusing. I determined that I only needed the one with the black tubing for my Kenmore refrig. Turned off water supply and vacuumed up all the dust bunnys behind refrig. Removed bottom grate on refrig where black tubing attaches at the other end. Released water left in t
... Read more
ubing at dispenser. I did not have to remove the front panel. Removed one screw attaching the nozzle to the dispenser. Decoupled tubing at the far end, more water came out here too. Pulled out upper end of tubing a couple of inches and snipped off. Attached tubing to new tubing with thin wire (as others here recommended) and had my husband pull at far end while I pushed slowly at the dispenser end. Once through reattached screw at top and recoupled at the bottom. Mission accomplished!
Read less
Was this helpful?
Thank you for voting!
Clogged Ice shoot in freezer door (curshed ice)
20 of 25 people
found this instruction helpful.
-
Lue from Wichita, KS
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
First remove the ice container from the freezer
and dump all of the ice. Remove the four
screws holding the front ice container cover. Remove the control arm screw and bracket from the bottom of the ice container, remove crusher housing (screws and retainer clip). Remove nylon
bearing nut on front of auger shaft (left ha ... Read more nded threads). Remove crusher blades and spacers (remember order of blades and spacers). Remove broken floating baffle. Replace baffle and reverse removal procedures.
and dump all of the ice. Remove the four
screws holding the front ice container cover. Remove the control arm screw and bracket from the bottom of the ice container, remove crusher housing (screws and retainer clip). Remove nylon
bearing nut on front of auger shaft (left ha ... Read more nded threads). Remove crusher blades and spacers (remember order of blades and spacers). Remove broken floating baffle. Replace baffle and reverse removal procedures.
Read less
Was this helpful?
Thank you for voting!
Ice door holder arm broken
20 of 26 people
found this instruction helpful.
-
Joseph S from Las Vegas, NV
- Easy
- 15 - 30 mins
-
Nutdriver
The hardest part was getting the front cover plate off. I used two kitchen knifes one in each slot on the bottom of the plate and pried it off and unplug it. I removed one screw to release arm. I then used long nose pliers to remove the pin on door arm assemble. Then unplug door heater. New door has no heater. The heater had cooked the pl
... Read more
astic arm, which caused the arm to fail. Then reassemble in reverse order.
Read less
Was this helpful?
Thank you for voting!
drawer broke from kids overloading it.
20 of 27 people
found this instruction helpful.
-
jonathan from sugar hill, GA
- Really Easy
- Less than 15 mins
Pulled out the old drawer and put in the new.
Was this helpful?
Thank you for voting!
Unable to set the cold-control to a sufficiently cold setting.
36 of 75 people
found this instruction helpful.
-
Leo from Lewisport, KY
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Linkage on the cold-control mechanism in the air diffuser assembly was broken. It was necessary to access the diffuser assembly from both the refrigerator and freezer sides of the unit.
Re-connected the linkage between the diffuser and cold-control assembly; remounted the two combined assemblies . . . refrigerator working nicely now ... Read more .
Re-connected the linkage between the diffuser and cold-control assembly; remounted the two combined assemblies . . . refrigerator working nicely now ... Read more .
Read less
Was this helpful?
Thank you for voting!
Ice maker wouldn't deliver ice.
19 of 25 people
found this instruction helpful.
-
Berton from Albuquerque, NM
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Removed face plate, disconnected wires, removed and replaced micro switch and control bracket.
Other Parts Used:
Was this helpful?
Thank you for voting!
Broken Drawers
21 of 31 people
found this instruction helpful.
-
Fiona from Newman, CA
- Really Easy
- Less than 15 mins
I replaced the Crisper Pan with no problem. The snack Crisper Drawer doesn't come with the white trim, so you have to take it off the broken drawer and put it on the new one. I think removing the trim & putting it on the new drawer was the most difficult part since it is such a snug fit! Still, it only too a couple of minutes. Now I am wo
... Read more
ndering why I waited so long to order new drawers!! Thanks Parts Select!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The Ice Maker Deflector Broke and Needed Replacing
17 of 19 people
found this instruction helpful.
-
Tony from Victorville, CA
- Easy
- 15 - 30 mins
-
Screw drivers
I first removed the ice bin from freezer. There were four nut screws on back of ice bin cover that I removed with a screw driver, giving me access to the deflector. The deflector has two prongs that attach it securely to the ice bin, I used a phylips head screw driver to release the prongs from the deflector. I installed the new deflector
... Read more
by placing it through the bottom portion of deflector area, using the phyllips screw driver I engaged the prongs of the deflector into slots on ice bin. There was a hook on the back side of the deflector that went over a metal rod that controls the ice cube release. Then replace front cover of ice bin with the four nut screws and returned it to the ice maker location.
Read less
Was this helpful?
Thank you for voting!
nozzle on water dispenser broke off.
16 of 17 people
found this instruction helpful.
-
Tom from Roseville, CA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
First, turn of the water supply. Then remove the snap on grill from the bottom front of the refrigerator. Disconnect the black hose from the white hose and drain the hoses into a suitable recepticle. Then remove the 1/4" screw that holds the nozzle in place. Cut the hose off just behind the nozzle bracket and tape the end of the new h
... Read more
ose to the now exposed end of the existing hose. From the bottom of the door you can now gently pull out the old hose while pulling in the new one. Re-attach the new hose to the existing white hose and replace the 1/4' screw to the new nozzle bracket. I reccoment using 1" wide tape and only going around the tubes once. Too much tape and you won't be able to feed it through the small hole at the bottom of the door. Have someone feed the hose from the top as you gently pull from the bottom.
Read less
Was this helpful?
Thank you for voting!