EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3VED Whirlpool Refrigerator - Instructions

All Instructions for the 3VED
16 - 30 of 1368

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The Bearing Cup Assembly was broken and ice would jamb against it during the ice making cycle.
110 of 140 people found this instruction helpful.
  • David from Chester, CA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
I removed the ice maker from the refrigerator, by removing one screw on the underside bracket and loosening the two screws at the top side, then lifting the ice maker off the loosened screws. I then unplugged the electrical harness that supplies power from the refrigerator to the ice maker. I then disassembled the ice maker by removing the front cover which is snapped in place, then removing two recessed screws at the front. I removed the broken part, I then reassembled the ice maker with the new part. I replaced the two recessed screws at the front and snapped on the cover. Then I reinstalled the ice maker in the refrigator by plugging in the harness, slipping the ice maker over the loosened screws in the refrigerator and replacing the screw that was removed from the underside bracket. Tightening all the screws completed the project.
Was this helpful?
Thank you for voting!
Refrigerator was not cooling properly.
73 of 76 people found this instruction helpful.
  • Eddie from Gretna, LA
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
I removed both plastic knobs from assembly faceplate. Then I loosened the screws holding thermostat housing to upper cabinet of fridge. Following this step, I loosened the screws of the thermostat to remove it. Next was the removal of the plate and vent pieces holding the thermostat wire sleeve in place. After removal of thermostat from s leeve; all steps were reversed and unit was up and running normal (cooling) with no problems. "Ahh, it's nice to have cool again "
Was this helpful?
Thank you for voting!
Broken Criper drawer
105 of 175 people found this instruction helpful.
  • Victor from Morgan Hill, CA
  • Really Easy
  • Less than 15 mins
First I opened the fridge and removed the broken drawer. I then removed the new drawer from its shipping container and placed it on the tracks in the fridge. I then closed the fridge. Perfect!
Was this helpful?
Thank you for voting!
No ice in ice trey
79 of 104 people found this instruction helpful.
  • Wayne from Leesburg, FL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
The easiest thing to do was pull the ice make off. After taking the 3 screws out of the wall of the freezer, take a screwdriver (flathead) and push on the tab for the electrical plug and wiggle the cord out. Then you can take 3 screws out for the main cover and another 2 screws on the next cover. There's the part, pop it out and replace h olding pins and start the process of putting back together the opposite way you took it apart.
Was this helpful?
Thank you for voting!
Plastic Auger on the Ice Maker broke.
70 of 78 people found this instruction helpful.
  • Wallace from Weslaco, TX
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Was very confused when the part sent out looked nothing like the one it would replace. There was a note in the package saying that this would replace it but I was doubtful. Suggest that it be made very clear that this is an upgraded part to replace a bad design.Had not problem once i checked the website and found this to be correct replac ement part. I didn't have any problem with the order of the crusher blades as once I removed the shaft nut I slid all of the parts in order onto the awl. Then it was a simple matter of sliding them off of the awl onto the auger shaft. The new metal auger works much better than the plastic one it replaces.
Was this helpful?
Thank you for voting!
Water would not dispense.
76 of 100 people found this instruction helpful.
  • Timothy from Junction City, OR
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Unplug the refrigerator. Snap off the ring surrounding the dispenser from the bottom. There are two slots on the bottom. This is the toughest part of the repair because my refigerator is older and the part stuck. Then unscrew the two hex screws and unsnap the parts, then reassemble with the new parts. Snap the ring back on and you're all set. Pretty easy.
Was this helpful?
Thank you for voting!
The studs to hold the shelf were broken
67 of 73 people found this instruction helpful.
  • Pavel from Norwalk, CT
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers
The hardest part was to figure out how to remove the old studs and put in new ones. I figured out finally that they should be twisted out and in., Simple online or printed insruction would be very helpful. Unfortunatelly the manual does not contain any repair information.
I fixed it with little trouble.
Was this helpful?
Thank you for voting!
Drawer Broke
66 of 71 people found this instruction helpful.
  • Brian from Fort Collins, CO
  • Really Easy
  • Less than 15 mins
I first opened a beer to gain some liquid courage. The crowd (dog and 2yr old) were anxiously watching while I first grabbed hold of the refrigerator door. The door swung open with a mighty roar exposing the huge gaping whole where the previous crisper pan once shelved itself in glory. I took aim, and slid that new crisper pan in like it was meant to be. The crowd went nuts...but probably because the tv commercial was over and Sesame Street was back on. Thanks partselect!
Was this helpful?
Thank you for voting!
Plastic broken around ice maker shaft
61 of 70 people found this instruction helpful.
  • Gary from Denham Springs, LA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I removed the 4 screws from the inside front of the container that held the ice maker shaft in place. This allowed me to remove the old broken container from the front assembly. It was just a matter of attaching the new container to the front assembly and sliding the new container back into the freezer. I am back in business and I coul dn't believe how easy it was to make this repair. Shipping was very speedy and communication was fast. I will use PartSelect.com again and refer family and friends for a good deal.
Was this helpful?
Thank you for voting!
Broken light switch
82 of 134 people found this instruction helpful.
  • Randy from Hays, KS
  • Really Easy
  • 15 - 30 mins
  • Socket set
Took all the screws out of the plastic shroud that encloses the switch .There only four that I needed to remove, were the two in front where the switches that go,they go in horizontally and two in the back with large washers on them that hold the back to the top of the box that go in vertically.The switch was a snap ( make that two snaps ) the wiring is almost self explanatory. then it gos back to the way you took it off. OH! and don't forget to turn the light bulb all the way back in to the socket , so the light will work after you take the time to install it yourself.I had the water supply line from under the box to the water dispenser in the door and the total bill on that was one hundred thirty seven and a hand full of change.Don't be afraid to do it yourself the savings is enough on one one item to make several months payments on a new one Randy the "Handy Man'
Was this helpful?
Thank you for voting!
Light Would Not Go On In The Refrigerator
62 of 82 people found this instruction helpful.
  • DANIEL from MINNEAPOLIS, MN
  • Easy
  • Less than 15 mins
  • Screw drivers
First I removed the old lightbulb from the socket and replaced it with a new one to confirm that the bulb was not the problem. I then pryed the socket out with a flat-head screwdriver. I could tell that the socket was anchored in its hole with clips so it was relatively easy to pry it out. Once the socket was out, I disconnected the le ad wires and ordered a replacement socket kit from Partselect. When the new one arrived, I reconnected the lead wires to it, snapped it back into its hole, screwed in a new lightbulb, and presto!! The light was back on with no further problem. Thank you, Partselect!! A $15.00 part saved me what probably would have been at least a $100. service call and heaven knows what the technician would have told me I needed!!!
Was this helpful?
Thank you for voting!
plastic Ice bin auger broke and needed to be replaced
56 of 67 people found this instruction helpful.
  • Suzanne from Colorado Springs, CO
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
The repair was actually easy; however I have an ice dispencer/crusher attached and the which the diagram supplied with the part did not include. I had to make several calls before I was e-mailed the diagram.
Suggestions: note that the screw at the end of the auger goes in the reverse direction (this took me about 20 minutes to fi gure out even though it was shown in the diagram). Also, be sure to keep the ice crusher parts in order and be sure the white plastic tab on the crusher fits into a depression in the housing. I did not notice this and had to take it all apart and redo the install. It works great!!!
Was this helpful?
Thank you for voting!
broken shelves
60 of 88 people found this instruction helpful.
  • Maria from Albuquerque, NM
  • Really Easy
  • Less than 15 mins
replaced with new shelves
Was this helpful?
Thank you for voting!
Ice dispenser would not operate
46 of 49 people found this instruction helpful.
  • John from Poway, CA
  • Easy
  • Less than 15 mins
  • Screw drivers
The control bracket is made of plastic and holds two microswitches that activate the ice dispenser and the water dispenser. The plastic clips that held the switches on the control bracket broke so that the switches no longer operated when the ice dispenser lever was operated.

Two screws held the external dispenser bezel, and t wo screws held the control bracket in place. The wiring and switches were transferred to the new bracket and the new bracket screwed into place. Then the bezel was replaced.

Total repair time was less than 5 minutes. The control bracket was $16.50 with shipping and arrived two days after I placed the order.

The PartSelect website had a clear diagram of the control bracket so I was comfortable with the order.
Was this helpful?
Thank you for voting!
Door was making a clunking noise
46 of 49 people found this instruction helpful.
  • Erik from Yorba Linda, CA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
The door is very easy to remove. There is one nut for the cap on the top of the soor hinge. Once the cap is removed, you need to remove the 3 nuts holding the hinge in place. Simply lift the door off the lower hinge and rest it on the dining room table. I set towels down to protect the stainless finish. The closing cam will be visible on the bottom of the door. I choose to replace the lower cam and the upper cam at the same time. I did not know what the problem cam was. The door works good as new. I put a small amount of vaseline where the two cams rub to provide a lubricant.
Was this helpful?
Thank you for voting!
All Instructions for the 3VED
16 - 30 of 1368