3RLS Whirlpool Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Pump but not spin-oil leaking-agitation noise
11 of 12 people
found this instruction helpful.
-
Alvaro from CLEMENTON, NJ
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set
Replaced AGITATOR DIRECTIONAL COGS (4) looking instruction video . Replaced CLUTCH LINING KIT following video of this site "WASHER REPAIR-REPLACING THE CLUTCH ASSEMBLY". Replaced SEAL, GEARCASE COVER and NEUTRAL DRIVE ASSEMBLY as follow: 1)CLUTCH Assembly and motor removed, took the GEARCASE on a bench vise to hold in place and the lo
... Read more
ng shaft up side. You can get help from other person to hold secured in place instead a vise.2)Following a youtube video I tested gearcase with a reversible drill using DIRECT DRIVE MOTOR COUPLING PART next To transmission side instead of electrical motor. Drill turning counter clockwise drive the long shaft oscillating (it agitate via agitator cogs). Drill turning clockwise run the exterior sleeved part around shaft (upper side of metal gear inside gearcase and fixed on top to clutch to get washer spin). My experience was didn't rotate so we had to take apart gearcase cover.3)Unscrewed and removed gearcase cover. Cover was sticked by old seal gasket so a screwdriver helped me to remove it.4)Cleaned joint removing old gasket.5)Repeating drill test I realized big nylon gear did'nt rotated and removed uppercut clip with pin pliers with care for not lose the pin. Removed the next washer, the plastic gear and found a plastic part with a tooth broken. This part is with NEUTRAL DRAIN ASSEMBLY so replaced assembly following part instructions. I recommend take pictures in order to reassemling and use ALLEN WRENCH 5/32'' inches.6)Fill up to half of gearcase with 16 ounces (about 1/2 of case) of gear oil supplied by PARTSELECT or automotive gear oil SAE 85w90 or SAE 90.7)Replaced SEAL, GEARCASE COVER. HARD TO REMOVED AND REPLACE! Take care not break!. I had to use a piece of metal tube and a vise.8)Applied automotrice black seal gasket silicone around the cover joint and case.9) Replaced the cover and reversal instruction video.THANKS to this site I get excellent service and Enjoyed with my toy.
Read less
Was this helpful?
Thank you for voting!
Washer's Agitator wasn't working
13 of 19 people
found this instruction helpful.
-
David from Barrington, RI
- Really Easy
- Less than 15 mins
-
Socket set
Basic replacement so easy my nine yr old daughter did the needed repair we watched the video on your web site Way to go Alexis . Ten minutes later all done ! Probably saved a few hundred dollars or more, no service calls or no need to replaced our beloved washer (Cira 1994) they really don't make them like this anymore, will use your co
... Read more
mpany again if needed Thanks !!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
would not move clothes
16 of 28 people
found this instruction helpful.
-
phillip from worcester, MA
- Easy
- 15 - 30 mins
-
Socket set
Took the cup for the clothes softner out, just pulls out, took plastic seal out, just pulls out, took the socket set,with an exstention, unscrewed the bolt & pulled out the agitator. easy. Reverse the process in putting the agitator back. P.S. Right hand thread.
.
.
Was this helpful?
Thank you for voting!
Washer was leaking underneath machine
10 of 10 people
found this instruction helpful.
-
RAY from DEER PARK, TX
- Easy
- 30 - 60 mins
While taking apart my washing machine to clean the plastic basket I discovered the 3 main seals down the agitator were completely disintegrated and water was leaking onto the motor and onto the floor. The seals are a tight fit but slide into place easily with lubrication. When putting everything back together a bit of lubrication will be
... Read more
necessary as well. The leak is gone and my nearly 30 year old washer is working as well as the day it came off of the assembly line.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Water level switch broke off in the knob.
11 of 13 people
found this instruction helpful.
-
Larry from Hyden, KY
- Really Easy
- 30 - 60 mins
-
Screw drivers
Unplugged the washer from the power. Turned off the hot and cold water. Took two screws off the back and raised up the upper cover. Took the power cables and water tube loose from the water level switch. Removed the switch. Put the new switch in. Removed two metal clips at the top of the washer and leaned the washer body forward. Replaced
... Read more
the tube with a new one. Put the washer body back in place and put the clips back in. Attached the tube to the new switch along with the power cables. Let the top cover back down and put in the two screws. Slid the new knob in place. Plugged up the washer to the power. Turned the hot and cold water back on. And commenced washing laundry.
Read less
Was this helpful?
Thank you for voting!
Washer was leaking.. determined it was center gasket
10 of 10 people
found this instruction helpful.
-
Diane from BALTIMORE, MD
- Very Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Completely dismantled washer per video , replaced gasket and spanner nut, then re-assembled washer. I’m a 58 year old female. It was tough. Main issue was that video was for dif. Model washer. Had to figure out some things myself.
Other Parts Used:
Was this helpful?
Thank you for voting!
drive shaft leaking
10 of 10 people
found this instruction helpful.
-
Al from OCEAN, NJ
- A Bit Difficult
- 1- 2 hours
-
Screw drivers, Socket set
Washer was leaking -- in part from hoses that had loosened over time due to unbalanced loads and age, and partly from a worn pump -- and not agitating/spinning properly. Fixed hoses, replaced pump and clutch. Unfortunately, when I pulled apart direct drive to replace clutch, the drive shaft started leaking because old seals worn and comp
... Read more
romised on disassembly. Have to give credit where due -- YouTube invaluable here -- pulled and disassembled drive shaft, removed old seals, replaced and reassembled. Time consuming, but if you keep track of where things go, not too bad. 3 things I wish I knew in advance: (1) for an old washer you definitely need a spanner nut wrench (like 15-25 bucks online) to remove the spanner nut so you can pull the basket and get to the seals -- no wrench/pliers/vise substitute will do the trick; (2) the shaft seals have metal washers inside the rubber/plastic -- when you're removing the old seals, you might need to chisel (hammer and small flat head screwdriver) the old seals out instead of just pulling out the corroded rubber which will leave the old metal behind; (3) if your time is valuable, try to diagnose all the likely sources of your problem and buy the parts to repair at once rather than doing piecemeal like me. Took me 2 weeks and two complete tear downs to finish a repair that should have taken me an afternoon. I love my local Appliance Parts guy -- he's knowledgeable and usu. has what I need or can get it fast and I like supporting local brick and mortar -- but if time is important to you, taking advantage of online companies that allow you to return what you don't use may save you time.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The wash cycle did not start.
10 of 11 people
found this instruction helpful.
-
Dwane from Cincinnati, OH
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
First I removed the plastic panels on each side the control panel. Each side was secured by a phillips screw. Once the screws were removed the side panels were easily removed. I tilted the panel back to the rear of the washing machine to expose the lid switch. I first took a picture with my camera phone to ensure installing the switch
... Read more
correctly. I removed a small screw that secured a green ground wire. The lid switch was removed by lifting the plastic catch with a flathead (or slot) screwdriver and uplugging the switch. Reverse the steps and install the new switch. Secure and tighten the green ground wire. The lid must be lifted to properly seat the lid's guide arm into the lid switch. Replace the side panels and tighten the phillip screws. Test the wash cycle using a low water level. It took me 5 minutes to install this part. I am a attorney not a mechanic.
Read less
Was this helpful?
Thank you for voting!
Washer would not wash,spin or drain.
11 of 14 people
found this instruction helpful.
-
Michael from Covington, LA
- Really Easy
- Less than 15 mins
-
Screw drivers
I thought that the lid switch was the problem why the washer would not perform the drain or spin cycle. I broke the lid switch by moving the wires around. I rigged it so my daughter could use it by screwing a screw in the switch til the new one came in. After a few days, the machine stopped working again as stated above with the motor. I
... Read more
purchased a new Whir-pool washer for her and later found a white wire that connects to the electric motor was burnt around the connector in that only one tiny wire was still attached. I reconnected the wire in the connector and the washer started working again.
Read less
Was this helpful?
Thank you for voting!
washing machine not draining
10 of 11 people
found this instruction helpful.
-
michael from princeton, TX
- Easy
- 15 - 30 mins
-
Pliers
Tilt machine on its side,snap off the two retaining straps and remove the pump and sanded the shaft on the electric drive motor to remove rust ,Install new pump and retaining straps and unit now running great.
Was this helpful?
Thank you for voting!
Replaced ring that broke and washer that was bent on the edge.
22 of 47 people
found this instruction helpful.
-
Kim from West Liberty, OH
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
Took the agitator out and gearbox off unhook wires from motor and take off water pump, replaced the parts and put back together. Pretty easy to fix. However, I still haven't got my problem fixed. Originally the washer wouldn't spin after the rinse. I put on a new coupler and it worked for a few loads, then something smelled hot and starte
... Read more
d stinkin the house up so I opened the washer lid and smoke rolled out. Turned it off. Took the moter off and checked it and it would barely turn at all. Replaced the motor with a new one. Still wouldn't spin. Put on a new clutch assembly. Still wouldn't spin. Bought a new capacitor thinking that would do it. Still don't SPIN!!! (The ring and washer I replaced was just a casualty, not any of the problem).
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
tub oscillation
12 of 17 people
found this instruction helpful.
-
leonard from phil campbell, AL
- Really Easy
- 15 - 30 mins
-
Pliers
placed washer on side and installed new pads
and returned washer upright
and returned washer upright
Was this helpful?
Thank you for voting!
spin cycle was not working / poor
11 of 14 people
found this instruction helpful.
-
Craig from Plano, TX
- Easy
- 30 - 60 mins
-
Pliers, Socket set
Unplugged the appliance. turned off inlet water and removed hoses. popped the cap off hiding the bolt that keeps the agitator in place and pulled the agitator off. tipped the washer on its front . disconnected the Wire harness. removed the 3 bolts that hold the pump, motor,clutch, (drive assembly in other words). pulled the Drive ass
... Read more
embly out of its resting spot removed the bad clutch and replaced it with the new one. then reassembled in reverse order.
Read less
Was this helpful?
Thank you for voting!
Making Alot Of Nosie While Washing
12 of 18 people
found this instruction helpful.
-
CHRISTI from NEWPORT NEWS, VA
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
First I removed the fabric softner dispenser. Then I removed cap took screw out removed agitator asseembly put new one in then I put screws back in.
Was this helpful?
Thank you for voting!
Tub banged against the front of case during spin
9 of 9 people
found this instruction helpful.
-
Peter from Boca Raton, FL
- A Bit Difficult
- Less than 15 mins
-
Screw drivers
3 online people recommended tilting the machine on the side and replacing the 3 suspension springs. Someone else recommended changing the tub pads. That is the wrong approach. It is actually easier to remove the case than turn the machine on the side. Once you do it once or twice it takes less than 2 minutes and it doesn't distort the
... Read more
suspension. You don't even have to disconnect the hoses. When I originally examined the machine lying on it's side I saw that the tub balance spring was still attached to the tub but the other end had detached. I looked for the place to reattach it. I found a place on the glide plate. Unfortunately this was the wrong place and the machine continued to bang away. When I realized that the spring had to be attached to the lower frame rather than the glide plate (one week of looking). I even wrote to the Repair guru. Once I found my mistake the repair took 5 minutes and no tools other than the phillips screwdriver to take out the 2 screws for the case. I replaced the tub balancing spring for good measure. The machine works great.
Read less
Was this helpful?
Thank you for voting!