EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3RLS Whirlpool Washer - Instructions

All Instructions for the 3RLS
91 - 105 of 1772

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
water leaking from pump
15 of 19 people found this instruction helpful.
  • michael from westmoreland city, PA
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Removed the clips. Pulled out the old pump. After trying to get the new pump on the shaft of the motor, I realized that some corrosion had built up on the motor shaft. I got a small tack hammer and very lightly tapped the shaft to remove the corrosion. The pump then slid on the shaft with no problem. Replaced clips. Job complete.
Th e corrosion on the shaft cracked the plastic piece where the shaft connects and this is what caused the problem in the first place.
Was this helpful?
Thank you for voting!
The washing machine know brokw
20 of 34 people found this instruction helpful.
  • gloria from dupont, WA
  • Really Easy
  • Less than 15 mins
While my friends were visiting, they broke the knob off my washer. Now I am no good at repairs of any type, so my initial reaction was to get a new washer. Instead I went on the website and found a new knob. The website made it easy to match model numbers and get the exact knob. I got it in the mail ASAP and I just pushed it on. This may not sound like an impressive repair story but trust me, it was a lot for me. I saved myself $400.
Was this helpful?
Thank you for voting!
Washer would not Agitate or spin out. Also noticed an oil leak.
14 of 16 people found this instruction helpful.
  • Jonathan from BRANDON, VT
  • Really Easy
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set
I followed instructions provided from Parts Select for removing and replacing the coupler assembly, and also instructions for changing the clutch assembly. I also took it's transmission apart (socket set and flat screwdriver required), drained the old oil, cleaned it, added new 90W gear oil. The instructions covered the swapping of parts very well. Cleaning up the oil spill took as long as changing the parts.
Was this helpful?
Thank you for voting!
pump leaking, agitator not turning
14 of 17 people found this instruction helpful.
  • Becky from Oskaloosa, IA
  • Really Easy
  • 15 - 30 mins
  • Pliers, Socket set
First I went to this site and read what everyone had to say on leaking pumps. After finding the model number, I looked at the parts list, and found what parts I thought I would need. First I shut off the water and unpluged the washer Replacing the water pump was very easy after reading what other people had done. I pulled the washer out from the wall about 18 inches and tilted back on a 45 degree angle. The pump was now in plain sight and helt in with two slide clamps. Using a pair of plyers I remover both clamps from both hoses on the pump. By pushing to the outside of the pump I was able to remove both of the slide clamps. This allows the pump to be lifted out and off the motor shaft. As my washer had just started leaking " about one week" the pump slid off the shaft easy. There was no rust on shaft. Pump shaft has a slot in it so the pump can only go on one way. By reversing the way I removed the pump I was able to slide the new pump back onto the shaft and slide the slip clamps back over the pump. Replacing both hoses and both clamps. Now pump was in place. I pulled the washer away from the wall and slid back into place. That took care of the pump. For the top side I removed the top part of the agitator by pulling up and removing the part that holds the softner. Under this was a piece of plastic that I was able to lift out. Under that was a 12MM bolt with a rubber washer. Using a scoket set I removed the bolt and washer. Lifting up on the agitator it came right out. Pulling on each end of the agitator I was able to pull it apart. Inside was a large plastic washer and agitator directional cogs all in one piece. This piece just lifts up and off. I replaced the old piece with the new on and slid the two agitator back togeather. Setting the agitator back into the washer and put the 12mm bold and rubber washer back on. Then I put the plastic back on and set the top softer cup back in place. Snapping in the bleach dispenser was very easy, just shap into place. Pluging the washer back in, and turning back on the water I ran the washer with no clothes in it so I could check for leaks and make sure everthing was working. Repairing both parts took about 30 minutes and now the washer is like new.
Was this helpful?
Thank you for voting!
Leaking water on floor under front center.
14 of 17 people found this instruction helpful.
  • Christopher from Leadville, CO
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Disconnet the washer from supply lines. pull washer out, tip on side. Remove water hoses from pump, have to squeeze hose clamps with pliers and slide them down the hose. Then remove the hoses from the pump. Then locate spring retainers that hold pump to drive motor, place flat blade screw driver under each clip and pry clip loose, then remove pump.
Install new pump on shaft, making sure that alignment dowels line up with holes on pump. Hold pump in place and using finger push retainer clips over lip of pump, install hoses on pump, install hose clamps. Hook washer up to supply lines, drain lines, plug in and you'r done.
Was this helpful?
Thank you for voting!
would not spin properly even with new coupling
16 of 24 people found this instruction helpful.
  • david from o, AL
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
Removed capscrew in end of agitator shaft took cover off machine-[ unscrewed two screws holding down control panel, hinged back, pryed retaining clips out, rocked back machine cover.]
Removed motor mounting clips and pump hoses, swinging motor and pump out of the way. Removed 3 capscrews holding transmission, pulled transmission towa rds me removing agitator shaft, disassembled clutch assembly - removing one cirlip then another, installed new clucth parts in same order
Was this helpful?
Thank you for voting!
Washer vibrates excessively on spin cycle
13 of 15 people found this instruction helpful.
  • Glenn from PROVO, UT
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
I followed the online instructions to remove the shell and attempted to remove the drum, but not having the special wrench to remove the special nut, tried using a screwdriver and hammer, which failed to loosen the nut. I then started examining the the undercarriage and saw that I could replace the springs without removing the tub and di d that. In the course of replacing the springs I discovered I could also access the wear pads by lifting the drum off of the undercarriage and placing a block to hold it above the pads. I was able to pop the old pads out by tapping underneath them with a hammer. The new pads were then installed and the weight of the drum popped them in. It was necessary to lift the drum assembly three times for each of the three pads.
Was this helpful?
Thank you for voting!
Agitator moves freely in both directions
14 of 18 people found this instruction helpful.
  • James from NAPERVILLE, AL
  • Really Easy
  • Less than 15 mins
  • Wrench set
First I removed the softener bin by pulling it up and off, then I removed the plastic seal by pulling it up and out, then I removed the 1/2 inch bolt with a ratchet and extension, then I removed the upper and lower agitator assembly from the machine and seperated the two by putting my feet on the lower agitator to hold it to the floor and pulling the upper agitator fast and firmly.
Sitting on top of the lower agitator I found the dog ear assembly. I pulled the dog ear assembly off and removed the yellow cap and existing dog ears.
Assembly was reverse.
Was this helpful?
Thank you for voting!
water leaking during run cycle
13 of 15 people found this instruction helpful.
  • michael from weymouth, MA
  • Really Easy
  • 15 - 30 mins
  • Pliers
flip machine back remove two spring clamps and hoses remove two spring clamps and water pump save $500.+on a new washer
Was this helpful?
Thank you for voting!
Wash machine, wouldn't spin dry the close. The pump still worked to drain the water.
17 of 27 people found this instruction helpful.
  • Matthew from Albany, MN
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers
Unplug power from wall.
Disconnected water lines
Tip Unit on it's side. (Recommend turning so motor is to the top side)
Disconnect Electrical connector and Hoses from the pump and motor.
Disconnect metal straps used to retain the motor to the transmission. (screwdriver to pry)
Remove old coupling pieces from trans mission/motor(used a long screw driver, rock back and forth)
used air compressor to clean up electric motor
replace new coupling on motor and transmisison (may need hammer to tap into place)
set rubber bushing on transmission side (transmission shaft should be facing up at this point)
replace electric motor into place, making sure to line up bushing and motor mounts.
replace metal strap connectors between transmission / motor (this can be tricky, as the one in the back is hard to get at.)
replace electrical connectors and hoses
connect washing machine power and water and test
Was this helpful?
Thank you for voting!
washer would no longer fill to proper height--just low
13 of 16 people found this instruction helpful.
  • keith from Bellaire, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers
removed top controls panel (not obvious),then released old switch by rotating 90 degrees (after disconnecting wires and pressure sensor tubing), then reinstalled new switch (new switch has only 3 positions, not 5 as old switch had) and reinstalled everything else.

A 'gotcha' is the plastic 'strap' on the back that anchors swit ch compartment to the back steel sheet. It is EASY to dislodge that plastic strap from the bakc panel and it drops down inside the panel--maybe to the floor, maybe not--requiring difficult retrieval. Suggest TAPING the plastic strap in place on the back steel sheet so it will not fall out.
Was this helpful?
Thank you for voting!
Will Not Spin
13 of 16 people found this instruction helpful.
  • Daniel from Temple, TX
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
This is a relatively new washer and failed early. My previous whirlpool washer lasted 20 years without any repairs. 1. First inquired about the spin problem in partselect. Machine will not sping unless manualy forced then it will take off but weak. 2. Partselect suggested a clutch problem. Ordered the part that came fast. When I tr ied removing the shaft hub with a hammer and chisel it will not get loose so I opted ordering the special wrench to loosen the tub hub. 3. I put the machine on its back and loosened the pump retaining clips. Do not remove the hoses from the pump. Move the pump away from the motor shaft. Remove the motor electrical connector and set aside. 4. Remove the three bolts holding the gearbox-motor assemply and pull it out of the tub. 5. Put the assembly on a towelwith shaft up and remove the separator washer from the old clutch that is sitting on the gearbox. Then remove the c-retaining clip from the shaft. 6. Pry out the wire retaining clip from the clutch and pull the old clutch out of the shaft. 7. The clutch kit I ordered came with a plastic brake to clutch cam so I replaced it too, just remove the retainig clip from the brake that is at the bottom of the tub and replaced the part. 8. Installed the new clutch and the retaining clips in reverse order. Replace all parts that came with the kit. The new clutch spring was already in place. 9. Put the assembly back into the tub and re-install all the other items in the same order. It spins good now! 10. While replacing parts, methodically clean all the lint from the motor and from under the machine. The gearbox showed signs of leaking oil so its a question of cost. I left it there until it fails then I'll buy a new machine.
Was this helpful?
Thank you for voting!
Washer model didn't come with softener dispenser
12 of 15 people found this instruction helpful.
  • Liz from Winchester, KS
  • Really Easy
  • Less than 15 mins
Just bought my washer and dryer from Home Depot, but bought an Admiral model that didn't come with a fabric softener dispenser. Ordered the part from PartSelect and after rocket fast shipping installed it in seconds. The installation required no tools as the dispenser just snapped right in. My clothes are now soft and free of static clin g. Thank you PartSelect!!
Was this helpful?
Thank you for voting!
Scratches in Surface
83 of 228 people found this instruction helpful.
  • Michelle from Richardson, TX
  • Really Easy
  • Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
Would not agitate on the top portion of agitator
11 of 12 people found this instruction helpful.
  • LYNN from Midlothian, VA
  • Easy
  • 15 - 30 mins
  • Socket set
Removed the softner dispenser and lifted up the plastic piece under that. Used a 9/16th socket with a long extension and unscrewed the center bolt.
Lifted the entire agitator parts off and out.
Next had to get husband to separate the top from the bottom, it was really hard for me. I am a woman but not weak!!
Replace the wa sher and the other 2 parts, and put it back together and it all took about 15 to 20 minutes.

Easy repair, even for a woman!!!
Was this helpful?
Thank you for voting!
All Instructions for the 3RLS
91 - 105 of 1772